Rig Pro about $160 per unit for a seal kit, new rod, double it. Do it yourself, $20 http://www.southernspars.com/
Harry Sent from my iPhone 8 beta > On Dec 31, 2016, at 15:14, David via CnC-List <cnc-list@cnc-list.com> wrote: > > No a place in Woburn, MA. > > David F. Risch > (401) 419-4650 (cell) > > > From: CnC-List <cnc-list-boun...@cnc-list.com> on behalf of Michael Cotton > via CnC-List <cnc-list@cnc-list.com> > Sent: Friday, December 30, 2016 3:39 PM > To: cnc-list@cnc-list.com > Cc: Michael Cotton > Subject: Re: Stus-List Fwd: Navtec 10 Series 7 > > Was that Tri-Power in Warwick? > > > On Friday, December 30, 2016 12:49 PM, David via CnC-List > <cnc-list@cnc-list.com> wrote: > > > I took mine to a truck repair shop after I paid a "Navtec Approved" repair > shop $500 only have it fail again in 14 months...no warranty so I was stuck > with another large bill. Didnt trust the repair so before going offshore > brought it to the truck shop to inspect and test. What cost $500 would have > cost $100 there. > > David F. Risch > (401) 419-4650 (cell) > > > From: CnC-List <cnc-list-boun...@cnc-list.com> on behalf of Dave Godwin via > CnC-List <cnc-list@cnc-list.com> > Sent: Friday, December 30, 2016 11:25 AM > To: cnc-list@cnc-list.com > Cc: Dave Godwin > Subject: Re: Stus-List Fwd: Navtec 10 Series 7 > > My original Navtec is in the shop right now. The highest price estimated was > $500 but both my rigger and the hydraulic guy said that would be worst case > scenario. For cost comparison purposes I asked if getting a new adjuster made > sense and the rigger said repair was the way to go. Which was my choice. The > rigger did recommend Sailtec as really good units. > > Best, > Dave Godwin > 1982 C&C 37 - Ronin > Reedville - Chesapeake Bay > Ronin’s Overdue Refit > >> On Dec 30, 2016, at 10:08 AM, Charlie Nelson via CnC-List >> <cnc-list@cnc-list.com> wrote: >> >> Replacing the seals is ~ $300 and any decent hydraulic shop can do it. If >> the piston sleeve is scored (unlikely), its junk. Otherwise, a seal >> replacement makes it perform like new. >> >> Charlie Nelson >> Water Phantom >> 1995 C&C 36 XL/kcb >> >> cenel...@aol.com >> >> >> -----Original Message----- >> From: Dave via CnC-List <cnc-list@cnc-list.com> >> To: John McKay <jmckay...@yahoo.ca> >> Cc: Dave <syerd...@gmail.com>; cnc-list <cnc-list@cnc-list.com> >> Sent: Fri, Dec 30, 2016 10:02 am >> Subject: Stus-List Fwd: Navtec 10 Series 7 >> >> John, have taken the liberty of forwarding this to the Cnc list. >> >> Subject: Re: Navtec 10 Series 7 >> >> John, >> >> When you say failed, I assume that you mean the seals now don't. >> If so, Plenty of industrial hydraulics places in the GTA - would expect they >> could fix? >> >> FYI - windstar (33-2) has no hydraulic adjuster, and if I understand >> correctly the baby stay is intended used to control mast bend, similar to >> backstab adjuster. Perhaps the adjuster was an 'owner-upgrade'? Did the PO >> happen to include the original part? (Look for a 1/2" stainless rod around >> 12" and toggles etc...) >> >> Good luck, dave. >> >> >> Sent from my iPhone >> >> On Dec 30, 2016, at 9:35 AM, John McKay <jmckay...@yahoo.ca> wrote: >> >> >> >> The Navtec backstay adjuster failed on Enterprise this summer. >> >> I know South Shore can repair it but it is a fairly expensive repair and >> searching on the net, most say a repair does not last that long. >> >> Has anyone replaced their adjuster? >> >> With what? >> >> Approximate cost? >> >> Or if repaired, where? >> >> Guys around my yacht club says it is an easy fix, but they are mechanically >> inclined! >> >> Thanks and Happy New Years >> >> John on Enterprise >> Komoka >> >> >> >> >> _______________________________________________ >> >> This list is supported by the generous donations of our members. If you wish >> to make a contribution to offset our costs, please go to: >> https://www.paypal.me/stumurray >> >> All Contributions are greatly appreciated! >> _______________________________________________ >> >> This list is supported by the generous donations of our members. If you wish >> to make a contribution to offset our costs, please go to: >> https://www.paypal.me/stumurray >> >> All Contributions are greatly appreciated! > > > _______________________________________________ > > This list is supported by the generous donations of our members. If you wish > to make a contribution to offset our costs, please go to: > https://www.paypal.me/stumurray > > All Contributions are greatly appreciated! > > > _______________________________________________ > > This list is supported by the generous donations of our members. If you wish > to make a contribution to offset our costs, please go to: > https://www.paypal.me/stumurray > > All Contributions are greatly appreciated!
_______________________________________________ This list is supported by the generous donations of our members. If you wish to make a contribution to offset our costs, please go to: https://www.paypal.me/stumurray All Contributions are greatly appreciated!
