All, I have a Neo Freerunner GTA02V5 to which I apparently flashed Qi some weeks ago. I'm not sure which version of FSO is flashed to memory, but I think it is milestone 3. In installing Qi, I think I may have been trying to recover from modifications made to uboot for Debian and probably ran the devirginator process to flash uboot before I went ahead and flashed Qi. I no longer recall why I did either.
And now, I'm a little confused as to how to proceed as I can no longer flash with dfu-util. When I boot to Nor and plug in the USB cable, I get a series of errors on my host and cannot use dfu-util. The errors are these: [ 87.928631] usb 1-1: new full speed USB device using uhci_hcd and address 3 [ 88.540254] usb 1-1: unable to read config index 0 descriptor/ start: -71 [ 88.540437] usb 1-1: chopping to 0 config(s) [ 88.695904] usb 1-1: string descriptor 0 read error: -71 [ 88.698093] usb 1-1: string descriptor 0 read error: -71 [ 88.700419] usb 1-1: string descriptor 0 read error: -71 [ 88.734000] usb 1-1: no configuration chosen from 0 choices [ 88.736092] usb 1-1: USB disconnect, address 3 [ 89.084376] usb 1-1: new full speed USB device using uhci_hcd and address 4 [ 89.692859] usb 1-1: invalid descriptor for config index 1: type = 0x2, length = 0 [ 89.692909] usb 1-1: can't read configurations, error -22 [ 89.912237] usb 1-1: new full speed USB device using uhci_hcd and address 5 [ 90.420975] usb 1-1: invalid descriptor for config index 1: type = 0x2, length = 0 [ 90.421000] usb 1-1: can't read configurations, error -22 [ 90.641355] usb 1-1: new full speed USB device using uhci_hcd and address 6 [ 90.676829] usb 1-1: invalid descriptor for config index 1: type = 0x2, length = 0 [ 90.676850] usb 1-1: can't read configurations, error -22 [ 90.900242] usb 1-1: new full speed USB device using uhci_hcd and address 7 [ 90.939088] usb 1-1: invalid descriptor for config index 1: type = 0x2, length = 0 [ 90.939111] usb 1-1: can't read configurations, error -22 [ 90.940610] hub 1-0:1.0: unable to enumerate USB device on port 1 This occurs whether the Freerunner is attached to the host first or not. Note: when booted into installed image, USB networking is fine and the above errors do not occur. Is this a host side problem or Neo Freerunner problem? I notice in the Qi documentation that there is no dfu-util support. Would that effect dfu-util in Nor? When I do attempt to boot into Nand, I end up with a Nor boot menu that is the same as when I boot into Nor - apparently either why the AUX/Power button are selected I boot to Nor. Is that correct behavior with Qi? BTW - my Nor boot menu seems slightly different than what I see on the wiki - rather than a Reset option in the fifth position I have Reboot. Are there any log or configuration files I should post to help diagnosis? I would like to be able to upgrade the release in memory or for that matter Qi - which I think I'm now blocked from doing. Is there an alternative to the "devirginator" process to restore the Freerunner to "factory" state? Thanks, Chris _______________________________________________ Openmoko community mailing list [email protected] http://lists.openmoko.org/mailman/listinfo/community
