El 04/12/11 18:34, Martin Jansa escribió:
On Sun, Nov 27, 2011 at 11:13:56PM +0100, ø wrote:
mmc1: new high speed SDHC card at address b368
mmcblk0: mmc1:b368 USD 3.74 GiB
mmcblk0: unknown partition table
Waiting 5sec before mounting root device...
VFS: Cannot open root device "mmcblk0p1" or unknown-block(179,1)
Please append a correct "root=" boot option; here are the available
partitions:
1f00 2048 mtdblock0 (driver?)
1f01 256 mtdblock1 (driver?)
1f02 256 mtdblock2 (driver?)
1f03 8192 mtdblock3 (driver?)
1f04 640 mtdblock4 (driver?)
1f05 256 mtdblock5 (driver?)
1f06 252544 mtdblock6 (driver?)
b300 3939112 mmcblk0 driver: mmcblk
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown
block(179,1)
Is this with 2.6.39 and shr-core? and do you have msdos partition table
or gpt? But both are supported by 2.6.39 config and IIRC were also
enabled in 2.6.37.
I'm so sorry for not answering before. I missed your mail. Only
yesterday I noticed it.
I wasn't install shr-core, but unstable (I was confused). I'm not sure,
but I think I tried with msdos partition table (I'm not very skilled
with that).
On my append-GTA02 I have:
rootdelay=5 rootfstype=ext2 loglevel=8 quiet splash
qi built by SHR has already rootwait included in default params (instead
of rootdelay=1), what you have to do with some uSD cards is to slow down
glamo_mci clock.
ie glamo_mci.sd_max_clk=1000000
in append-GTA02, see last comment from GNUtoo
http://trac.shr-project.org/trac/ticket/1275
but the clock is different for different cards ie my card works fine
with default clock and with glamo_mci.sd_max_clk=1000000 doesn't work at
all.
Woohoo! Yesterday I could boot! 1000000 didn't work for me, but I
googled different values and I found that
glamo_mci.sd_max_clk=12500000 glamo_mci.sd_drive=0
in the appendGTA02 line works.
Thank you so much, I recovered my daily phone.
Now, I have some different problems, with shr-core, but I will try
first, and then ask in other mail.
--
++`
.@@@@@@
:' .@@@@@@@@@#`
`@@@@@#++##@@@@@@@@@@@@@@@@`
:@@@@@@@@@@@@@@@@@@@@@@@@@@@@;
'@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
'@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@' ;
:@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ +
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@` :'
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@,@`
+`@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@:
..@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@+
'+@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
# @@@@@@@@@@@@@@@@@@@@@@@ @@@@@@@@@
+ +@@@# #@@@@@@@@@@@@@@@ . #@@@@@@
. ,@@@ @@@@@@@@@ :@@@@@,
# +@@. .@@@@@@@ `@@@@@`
`` `@@@ `@@ `@@ . .
@@@. .@; #@ @@
@@@ +@. #@ `@@
@@@` @@ :@; @@@
@@@+ @. @` @@@;
@':@ +: @ .@@@@
@` @; `@ @ ;@@@@
@ :@ `@ @` .@@@@
@ .@, @+ @' `@@@#
.@ #@ @, ;@ +@@.
'@@ , #+ '@, @`@
_______________________________________________
Openmoko community mailing list
[email protected]
http://lists.openmoko.org/mailman/listinfo/community
