Hi,
Patch applied.
It got further, but failed in the end.
mela...@jessy /usr/local/src/concordance/concordance $ sudo ./concordance
/tmp/LatestFirmware.EZUp
Concordance 0.21+CVS
Copyright 2007 Kevin Timmerman and Phil Dibowitz
This software is distributed under the GPLv3.
Requesting Identity: 100% done
NOTE: A firmware upgrade, will erase your remote's config and you will need
to update it. You may want to make a backup with -c or otherwise just use
the website.
Press <enter> to continue.
Invalidating Flash: done
Erasing Flash: 100% done
Writing firmware: 100% done
Resetting Remote: Failed to upload firmware: Unknown error
Segmentation fault
Remote now says 'safe mode' on the screen.
concordance can't find it :(
I tried from this post:
http://www.mail-archive.com/concordance-devel@lists.sourceforge.net/msg00085.html
mela...@jessy /usr/local/src/concordance/concordance $ sudo ./concordance -v
--direct -F /tmp/LatestFirmware.EZUp
Concordance 0.21+CVS
Copyright 2007 Kevin Timmerman and Phil Dibowitz
This software is distributed under the GPLv3.
ERROR: Couldn't initializing libconcord: Error connecting or finding the
remote
A bit of googling, and I followed the steps below:
1. Ensure the Remote is in "Safe Mode Requested" by taking out the
batteries, and disconnecting the remote from the USB cable.
2. Hold down the Off button and plug the remote into the USB.
3. Continue holding down the Off button for another 10 seconds. The remote
should then display the words "Safe Mode Requested".
4. With the unit in "Safe Mode Requested", re-install the firmware by
clicking Support on your home page.
Ok, here I ran the command sudo ./concordance -v --direct -F
/tmp/LatestFirmware.EZUp again, but got the same results, concordance can't
find the remote.
Any ideas how I can revive the remote (without windows) - don't have windows
here, but my wife can bring her windowz based laptop from work, so not all
is lost :)
from dmesg I have:
[100859.950698] usb 1-2: USB disconnect, address 4
[201408.196020] usb 2-1: new full speed USB device using uhci_hcd and
address 2
[201408.320461] usb 2-1: device descriptor read/64, error -71
[201408.548527] usb 2-1: device descriptor read/64, error -71
[201408.764043] usb 2-1: new full speed USB device using uhci_hcd and
address 3
[201408.888532] usb 2-1: device descriptor read/64, error -71
[201409.116019] usb 2-1: device descriptor read/64, error -71
[201409.332019] usb 2-1: new full speed USB device using uhci_hcd and
address 4
[201409.744518] usb 2-1: device not accepting address 4, error -71
[201409.856544] usb 2-1: new full speed USB device using uhci_hcd and
address 5
[201410.268533] usb 2-1: device not accepting address 5, error -71
[201410.268558] hub 2-0:1.0: unable to enumerate USB device on port 1
[201412.600026] usb 2-1: new full speed USB device using uhci_hcd and
address 6
[201412.784171] usb 2-1: configuration #1 chosen from 1 choice
[202016.488060] usb 2-1: USB disconnect, address 6
[202039.677679] usb 2-1: new full speed USB device using uhci_hcd and
address 7
[202039.859150] usb 2-1: configuration #1 chosen from 1 choice
[202041.960209] concordance[2906]: segfault at 8 ip 00007fbf9c2402d8 sp
00007fffa46661b0 error 4 in libconcord.so.1.0.0[7fbf9c236000+10000]
[202176.200057] usb 2-1: USB disconnect, address 7
[202228.996019] usb 2-1: new full speed USB device using uhci_hcd and
address 8
[202229.116027] usb 2-1: device descriptor read/64, error -71
[202229.344020] usb 2-1: device descriptor read/64, error -71
[202229.560027] usb 2-1: new full speed USB device using uhci_hcd and
address 9
[202229.680531] usb 2-1: device descriptor read/64, error -71
[202229.904021] usb 2-1: device descriptor read/64, error -71
[202230.120017] usb 2-1: new full speed USB device using uhci_hcd and
address 10
[202230.528017] usb 2-1: device not accepting address 10, error -71
[202230.640021] usb 2-1: new full speed USB device using uhci_hcd and
address 11
[202231.048523] usb 2-1: device not accepting address 11, error -71
[202231.048548] hub 2-0:1.0: unable to enumerate USB device on port 1
[202232.984183] usb 2-1: new full speed USB device using uhci_hcd and
address 12
[202233.166695] usb 2-1: configuration #1 chosen from 1 choice
-Lucas
On Fri, Aug 14, 2009 at 3:57 AM, Phil Dibowitz <p...@ipom.com> wrote:
> Lucas van Staden wrote:
> > Hi,
> >
> > Just checking if you got the original mail, with the firmware.
> > It was blocked by the list system, due to size.
> >
> > If not, I uploaded the latest firmware file to my server:
> >
> > http://www.dedmeet.com/files/LatestFirmware.EZUp
>
> Nope, the first email didn't come through. Thanks for the file.
>
> The attached patch should fix it.
>
> --
> Phil Dibowitz p...@ipom.com
> Open Source software and tech docs Insanity Palace of Metallica
> http://www.phildev.net/ http://www.ipom.com/
>
> "Never write it in C if you can do it in 'awk';
> Never do it in 'awk' if 'sed' can handle it;
> Never use 'sed' when 'tr' can do the job;
> Never invoke 'tr' when 'cat' is sufficient;
> Avoid using 'cat' whenever possible" -- Taylor's Laws of Programming
>
>
>
> ------------------------------------------------------------------------------
> Let Crystal Reports handle the reporting - Free Crystal Reports 2008 30-Day
> trial. Simplify your report design, integration and deployment - and focus
> on
> what you do best, core application coding. Discover what's new with
> Crystal Reports now. http://p.sf.net/sfu/bobj-july
> _______________________________________________
> concordance-devel mailing list
> concordance-devel@lists.sourceforge.net
> https://lists.sourceforge.net/lists/listinfo/concordance-devel
>
>
------------------------------------------------------------------------------
Let Crystal Reports handle the reporting - Free Crystal Reports 2008 30-Day
trial. Simplify your report design, integration and deployment - and focus on
what you do best, core application coding. Discover what's new with
Crystal Reports now. http://p.sf.net/sfu/bobj-july
_______________________________________________
concordance-devel mailing list
concordance-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/concordance-devel
