I've been running the SMP kernel (2.3.18-6.1mdksmp) for a few days without incident. But today, during boot, the boot stopped at the point shown in the dmesg snippet below. It stops dead, no errors etc, just stops. Once I let it set for about 10 minutes, but it never did proceed.
The regular kernel just breezes on by the bad port errors and boots. The only changes I made last night was to delete kaffe and install blackdown, but I seriously doubt that my java choice caused this. :) Being generally clueless about this stuff, I don't know where to look to start troubleshooting and am open to suggestions. I would also appreciate it if someone could tell me what these errors mean. BTW, this happens whether kudzu/harddrake is on or off. sharon [snipped from the regular kernel generated dmesg] RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize Uniform Multi-Platform E-IDE driver Revision: 6.31 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx --------------->>THE SMP KERNEL STOPS DEAD RIGHT HERE<<---------- IN from bad port cfc at c00a7500 IN from bad port cfc at c00a7500 IN from bad port cfc at c00a7500 IN from bad port cfc at c00a7500 IN from bad port cfc at c00a7500 IN from bad port cfc at c00a7500 IN from bad port cfc at c00a7500 IN from bad port cfc at c00a7500 IN from bad port cfc at c00a7500 IN from bad port cfc at c00a7500 IN from bad port cfc at c00a7500 IN from bad port cfc at c00a7500 IN from bad port cfc at c00a7500 IN from bad port cfc at c00a7500 IN from bad port cfc at c00a7500 IN from bad port cfc at c00a7500 IN from bad port cfc at c00a7500 IN from bad port cfc at c00a7500 IN from bad port cfc at c00a7500 IN from bad port cfc at c00a7500 IN from bad port cfc at c00a7500 IN from bad port cfc at c00a7500 IN from bad port cfc at c00a7500 IN from bad port cfc at c00a7500 IN from bad port cfc at c00a7500 IN from bad port cfc at c00a7500 IN from bad port cfc at c00a7500 IN from bad port cfc at c00a7500 IN from bad port cfc at c00a7500 IN from bad port cfc at c00a7500 IN from bad port cfc at c00a7500 IN from bad port cfc at c00a7500 IN from bad port c000 at c00a7614 IN from bad port c100 at c00a7614 IN from bad port c200 at c00a7614 IN from bad port c300 at c00a7614 IN from bad port c400 at c00a7614 IN from bad port c500 at c00a7614 IN from bad port c600 at c00a7614 IN from bad port c700 at c00a7614 IN from bad port c800 at c00a7614 IN from bad port c900 at c00a7614 IN from bad port ca00 at c00a7614 IN from bad port cb00 at c00a7614 IN from bad port cc00 at c00a7614 IN from bad port cd00 at c00a7614 IN from bad port ce00 at c00a7614 IN from bad port cf00 at c00a7614 pmac_ide: enabling IDE bus ID 2 pmac_ide: enabling IDE bus ID 0 pmac_ide: enabling IDE bus ID 1 hda: QUANTUM FIREBALLP LM30.0, ATA DISK drive hdb: IBM-DTLA-305010, ATA DISK drive hdc: HITACHI DVD-ROM GD-7000, ATAPI CD/DVD-ROM drive ide0 at 0xdd28b000-0xdd28b007,0xdd28b160 on irq 19 ide1 at 0xdd28f000-0xdd28f007,0xdd28f160 on irq 20 hda: Enabling Ultra DMA 4 ide_pmac: Set UDMA timing for mode 4, reg: 0x0c50038c hda: 58633344 sectors (30020 MB) w/1900KiB Cache, CHS=58168/16/63, UDMA(66) hdb: Enabling Ultra DMA 4 ide_pmac: Set UDMA timing for mode 4, reg: 0x0c50038c hdb: 19746720 sectors (10110 MB) w/380KiB Cache, CHS=19590/16/63, UDMA(66) hdc: Enabling MultiWord DMA 2 ide_pmac: MDMA, cycleTime: 120, accessTime: 90, recTime: 30 ide_pmac: Set MDMA timing for mode 2, reg: 0x00011d26 hdc: ATAPI 40X DVD-ROM drive, 512kB Cache, (U)DMA Uniform CD-ROM driver Revision: 3.12 Partition check: /dev/ide/host0/bus0/target0/lun0: [mac] p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 /dev/ide/host0/bus0/target1/lun0: [mac] p1 p2 p3 p4 p5 SCSI subsystem driver Revision: 1.00 [snip]
