On Thu, 18 Apr 2002 18:42:48 -0400 Sharon <[EMAIL PROTECTED]>(by way of Sharon <[EMAIL PROTECTED]>) wrote:
> I've been running the SMP kernel (2.3.18-6.1mdksmp) for a few days without > incident. But today, during boot, the boot stopped at the point shown in the > dmesg snippet below. It stops dead, no errors etc, just stops. Once I let it > set for about 10 minutes, but it never did proceed. > > The regular kernel just breezes on by the bad port errors and boots. The > only changes I made last night was to delete kaffe and install blackdown, but > I seriously doubt that my java choice caused this. :) > > Being generally clueless about this stuff, I don't know where to look to > start troubleshooting and am open to suggestions. I would also appreciate it > if someone could tell me what these errors mean. > > BTW, this happens whether kudzu/harddrake is on or off. > > sharon > > > [snipped from the regular kernel generated dmesg] > RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize > Uniform Multi-Platform E-IDE driver Revision: 6.31 > ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx > --------------->>THE SMP KERNEL STOPS DEAD RIGHT HERE<<---------- > IN from bad port cfc at c00a7500 > IN from bad port cfc at c00a7500 > IN from bad port cfc at c00a7500 > IN from bad port cfc at c00a7500 > IN from bad port cfc at c00a7500 > IN from bad port cfc at c00a7500 > IN from bad port cfc at c00a7500 > IN from bad port cfc at c00a7500 > IN from bad port cfc at c00a7500 > IN from bad port cfc at c00a7500 > IN from bad port cfc at c00a7500 > IN from bad port cfc at c00a7500 > IN from bad port cfc at c00a7500 > IN from bad port cfc at c00a7500 > IN from bad port cfc at c00a7500 > IN from bad port cfc at c00a7500 > IN from bad port cfc at c00a7500 > IN from bad port cfc at c00a7500 > IN from bad port cfc at c00a7500 > IN from bad port cfc at c00a7500 > IN from bad port cfc at c00a7500 > IN from bad port cfc at c00a7500 > IN from bad port cfc at c00a7500 > IN from bad port cfc at c00a7500 > IN from bad port cfc at c00a7500 > IN from bad port cfc at c00a7500 > IN from bad port cfc at c00a7500 > IN from bad port cfc at c00a7500 > IN from bad port cfc at c00a7500 > IN from bad port cfc at c00a7500 > IN from bad port cfc at c00a7500 > IN from bad port cfc at c00a7500 > IN from bad port c000 at c00a7614 > IN from bad port c100 at c00a7614 > IN from bad port c200 at c00a7614 > IN from bad port c300 at c00a7614 > IN from bad port c400 at c00a7614 > IN from bad port c500 at c00a7614 > IN from bad port c600 at c00a7614 > IN from bad port c700 at c00a7614 > IN from bad port c800 at c00a7614 > IN from bad port c900 at c00a7614 > IN from bad port ca00 at c00a7614 > IN from bad port cb00 at c00a7614 > IN from bad port cc00 at c00a7614 > IN from bad port cd00 at c00a7614 > IN from bad port ce00 at c00a7614 > IN from bad port cf00 at c00a7614 > pmac_ide: enabling IDE bus ID 2 > pmac_ide: enabling IDE bus ID 0 > pmac_ide: enabling IDE bus ID 1 > hda: QUANTUM FIREBALLP LM30.0, ATA DISK drive > hdb: IBM-DTLA-305010, ATA DISK drive > hdc: HITACHI DVD-ROM GD-7000, ATAPI CD/DVD-ROM drive > ide0 at 0xdd28b000-0xdd28b007,0xdd28b160 on irq 19 > ide1 at 0xdd28f000-0xdd28f007,0xdd28f160 on irq 20 > hda: Enabling Ultra DMA 4 > ide_pmac: Set UDMA timing for mode 4, reg: 0x0c50038c > hda: 58633344 sectors (30020 MB) w/1900KiB Cache, CHS=58168/16/63, UDMA(66) > hdb: Enabling Ultra DMA 4 > ide_pmac: Set UDMA timing for mode 4, reg: 0x0c50038c > hdb: 19746720 sectors (10110 MB) w/380KiB Cache, CHS=19590/16/63, UDMA(66) > hdc: Enabling MultiWord DMA 2 > ide_pmac: MDMA, cycleTime: 120, accessTime: 90, recTime: 30 > ide_pmac: Set MDMA timing for mode 2, reg: 0x00011d26 > hdc: ATAPI 40X DVD-ROM drive, 512kB Cache, (U)DMA > Uniform CD-ROM driver Revision: 3.12 > Partition check: > /dev/ide/host0/bus0/target0/lun0: [mac] p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 > /dev/ide/host0/bus0/target1/lun0: [mac] p1 p2 p3 p4 p5 > SCSI subsystem driver Revision: 1.00 > [snip] > Looks like it's dying loading SCSI. Do you have SCSI devices, or perhaps ide-scsi on the CD? Stew Benedict
