http://qa.mandrakesoft.com/show_bug.cgi?id=509
------- Additional Comments From [EMAIL PROTECTED] 2003-20-09 08:12 -------
Just did a new install of 9.2RC2 onto a HP Pavilion 503a with Intel 845G/GL chipset ..
I also
have this problem (plus non-working ethernet)..
Output of lspcidrake is below:
agpgart : Intel Corporation|82845 845 Chipset Host Bridge (MCH) [BRIDGE_HOST]
(vendor:8086 device:2560 subv:109f subd:3189)
Card:Intel 845 : Intel Corporation|82845 CGC [Chipset Graphics Controller]
[DISPLAY_VGA]
(vendor:8086 device:2562 subv:109f subd:3189)
usb-uhci : Intel Corporation|82801DB USB Controller [SERIAL_USB] (vendor:8086
device:24c2 subv:109f subd:3189)
usb-uhci : Intel Corporation|82801DB USB Controller [SERIAL_USB] (vendor:8086
device:24c4 subv:109f subd:3189)
usb-uhci : Intel Corporation|82801DB USB Controller [SERIAL_USB] (vendor:8086
device:24c7 subv:109f subd:3189)
ehci-hcd : Intel Corporation|82801DB USB Enhanced Controller [SERIAL_USB]
(vendor:8086 device:24cd subv:109f subd:3189)
i810_rng : Intel Corporation|82820 815e (Camino 2) Chipset PCI [BRIDGE_PCI]
(vendor:8086 device:244e)
i810-tco : Intel Corporation|82801DB 845G/GL Chipset ISA Bridge (ICH4)
[BRIDGE_ISA]
(vendor:8086 device:24c0)
unknown : Intel Corporation|82801DB 845G/GL Chipset IDE Controller
[STORAGE_IDE]
(vendor:8086 device:24cb subv:109f subd:3189)
unknown : Intel Corporation|82801DB SMBus Controller [SERIAL_SMBUS]
(vendor:8086
device:24c3 subv:109f subd:3189)
snd-intel8x0 : Intel Corporation|ICH4 845G/GL Chipset AC'97 Audio Controller
[MULTIMEDIA_AUDIO] (vendor:8086 device:24c5 subv:109f subd:3189)
8139too : Realtek|RTL-8139 [NETWORK_ETHERNET] (vendor:10ec device:8139
subv:109f subd:3189)
Hsf:www.linmodems.org: Conexant|HSF 56k HSFi Modem [COMMUNICATION_OTHER]
(vendor:14f1 device:2f00 subv:155d subd:8d8b)
unknown : Linux 2.4.22-6mdk ehci_hcd|Intel Corp. 82801DB USB2 [Hub|Root Hub]
(vendor:0000 device:0000)
unknown : Unknown|USB UHCI Root Hub [Hub|Root Hub] (vendor:0000 device:0000)
unknown : Unknown|USB UHCI Root Hub [Hub|Root Hub] (vendor:0000 device:0000)
modules.conf lists snd-intel8x0, but module is not loaded. Manual loading results in
output
below:
Hint: insmod errors can be caused by incorrect module parameters, including invalid IO
or
IRQ parameters.
You may find more information in syslog or the output from dmesg
Output of dmesg follows:
Linux version 2.4.22-6mdk ([EMAIL PROTECTED]) (gcc version 3.3.1 (Mandrake
Linux 9.2 3.3.1-2mdk)) #1 Sun Sep 7 18:11:19 EDT 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000007cf0000 (usable)
BIOS-e820: 0000000007cf0000 - 0000000007cff000 (ACPI data)
BIOS-e820: 0000000007cff000 - 0000000007d00000 (ACPI NVS)
BIOS-e820: 0000000007d00000 - 0000000007e80000 (usable)
BIOS-e820: 0000000007e80000 - 0000000008000000 (reserved)
BIOS-e820: 00000000ff800000 - 00000000ffc00000 (reserved)
BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
126MB LOWMEM available.
ACPI: have wakeup address 0xc0001000
found SMP MP-table at 000f6690
hm, page 000f6000 reserved twice.
hm, page 000f7000 reserved twice.
hm, page 0009f000 reserved twice.
hm, page 000a0000 reserved twice.
On node 0 totalpages: 32384
zone(0): 4096 pages.
zone(1): 28288 pages.
zone(2): 0 pages.
ACPI: RSDP (v000 PTLTD ) @ 0x000f66d0
ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ 0x07cf8bf7
ACPI: FADT (v001 INTEL NBGV 0x06040000 PTL 0x00000003) @ 0x07cfef14
ACPI: MADT (v001 PTLTD APIC 0x06040000 LTP 0x00000000) @ 0x07cfef88
ACPI: BOOT (v001 PTLTD $SBFTBL$ 0x06040000 LTP 0x00000001) @ 0x07cfefd8
ACPI: DSDT (v001 INTEL Brkdle_G 0x06040000 MSFT 0x0100000d) @ 0x00000000
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 Pentium 4(tm) APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x00] polarity[0x1] trigger[0x1] lint[0x1])
Using ACPI for processor (LAPIC) configuration information
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: Product ID: APIC at: 0xFEE00000
I/O APIC #1 Version 32 at 0xFEC00000.
Enabling APIC mode: Flat. Using 1 I/O APICs
Processors: 1
Building zonelist for node : 0
Kernel command line: auto BOOT_IMAGE=linux ro root=301 devfs=mount acpi=ht
resume=/dev/hda5
Initializing CPU#0
Detected 1694.545 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 3381.65 BogoMIPS
Memory: 124172k/129536k available (1487k kernel code, 4912k reserved, -1936k data,
152k init, 0k highmem, 0k BadRAM)
Dentry cache hash table entries: 16384 (order: 5, 131072 bytes)
Inode cache hash table entries: 8192 (order: 4, 65536 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 32768 (order: 5, 131072 bytes)
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 128K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 3febfbff 00000000 00000000 00000000
CPU: Common caps: 3febfbff 00000000 00000000 00000000
CPU: Intel(R) Celeron(R) CPU 1.70GHz stepping 03
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
ENABLING IO-APIC IRQs
Setting 1 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 1 ... ok.
init IO_APIC IRQs
IO-APIC (apicid-pin) 1-3, 1-5, 1-9, 1-10, 1-11, 1-16, 1-17, 1-18, 1-19, 1-20, 1-21,
1-22, 1-23 not
connected.
..TIMER: vector=0x31 pin1=-1 pin2=0
...trying to set up timer (IRQ0) through the 8259A ...
..... (found pin 0) ...works.
number of MP IRQ sources: 19.
number of IO-APIC #1 registers: 24.
testing the IO APIC.......................
IO APIC #1......
.... register #00: 01000000
....... : physical APIC id: 01
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 00178020
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0020
.... register #02: 00000000
....... : arbitration: 00
.... register #03: 00000001
....... : Boot DT : 1
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 001 01 0 0 0 0 0 1 1 31
01 001 01 0 0 0 0 0 1 1 39
02 000 00 1 0 0 0 0 0 0 00
03 000 00 1 0 0 0 0 0 0 00
04 001 01 0 0 0 0 0 1 1 41
05 000 00 1 0 0 0 0 0 0 00
06 001 01 0 0 0 0 0 1 1 49
07 001 01 1 1 0 0 0 1 1 51
08 001 01 0 0 0 0 0 1 1 59
09 000 00 1 0 0 0 0 0 0 00
0a 000 00 1 0 0 0 0 0 0 00
0b 000 00 1 0 0 0 0 0 0 00
0c 001 01 0 0 0 0 0 1 1 61
0d 001 01 0 0 0 0 0 1 1 69
0e 001 01 0 0 0 0 0 1 1 71
0f 001 01 0 0 0 0 0 1 1 79
10 000 00 1 0 0 0 0 0 0 00
11 000 00 1 0 0 0 0 0 0 00
12 000 00 1 0 0 0 0 0 0 00
13 000 00 1 0 0 0 0 0 0 00
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 000 00 1 0 0 0 0 0 0 00
IRQ to pin mappings:
IRQ0 -> 0:0-> 0:0
IRQ1 -> 0:1
IRQ2 -> 0:2
IRQ4 -> 0:4
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1694.5936 MHz.
..... host bus clock speed is 99.6817 MHz.
cpu: 0, clocks: 996817, slice: 498408
CPU0<T0:996816,T1:498400,D:8,S:498408,C:996817>
mtrr: v1.40 (20010327) Richard Gooch ([EMAIL PROTECTED])
mtrr: detected mtrr type: Intel
ACPI: Subsystem revision 20030813
ACPI: Interpreter disabled.
PCI: PCI BIOS revision 2.10 entry at 0xfd99a, last bus=2
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: ACPI tables contain no PCI IRQ routing entries
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 00:1f.1
Transparent bridge - Intel Corp. 82801BA/CA/DB/EB PCI Bridge
PCI: Using IRQ router PIIX [8086/24c0] at 00:1f.0
PCI->APIC IRQ transform: (B0,I2,P0) -> 0
PCI->APIC IRQ transform: (B0,I29,P0) -> 0
PCI->APIC IRQ transform: (B0,I29,P1) -> 7
PCI->APIC IRQ transform: (B0,I29,P2) -> 7
PCI->APIC IRQ transform: (B0,I29,P3) -> 7
PCI->APIC IRQ transform: (B0,I31,P0) -> 1
PCI->APIC IRQ transform: (B0,I31,P1) -> 1
PCI->APIC IRQ transform: (B0,I31,P1) -> 1
PCI->APIC IRQ transform: (B2,I2,P0) -> 1
PCI->APIC IRQ transform: (B2,I11,P0) -> 7
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
Starting kswapd
kinoded started
VFS: Disk quotas vdquot_6.5.1
devfs: v1.12c (20020818) Richard Gooch ([EMAIL PROTECTED])
devfs: boot_options: 0x1
pty: 1024 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT
SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller at PCI slot 00:1f.1
PCI: Enabling device 00:1f.1 (0005 -> 0007)
ICH4: chipset revision 1
ICH4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x1860-0x1867, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x1868-0x186f, BIOS settings: hdc:DMA, hdd:pio
hda: ST320410A, ATA DISK drive
blk: queue c0180d20, I/O limit 4095Mb (mask 0xffffffff)
hdc: SAMSUNG CD-ROM SC-148C, ATAPI CD/DVD-ROM drive
hdc: Disabling (U)DMA for SAMSUNG CD-ROM SC-148C
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 39102336 sectors (20020 MB) w/2048KiB Cache, CHS=2586/240/63, UDMA(100)
Partition check:
/dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 p6 >
ide: late registration of driver.
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 8192 bind 16384)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Resume Machine: This is normal swap space
Swsusp 1.0.3: kswsuspd starting
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 299k freed
VFS: Mounted root (ext2 filesystem).
Mounted devfs on /dev
Journalled Block Device driver loaded
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Mounted devfs on /dev
Freeing unused kernel memory: 152k freed
Real Time Clock Driver v1.10e
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 18:27:09 Sep 7 2003
usb-uhci.c: High bandwidth mode enabled
PCI: No IRQ known for interrupt pin A of device 00:1d.0. Probably buggy MP table.
usb-uhci.c: found UHCI device with no IRQ assigned. check BIOS settings!
PCI: Setting latency timer of device 00:1d.1 to 64
usb-uhci.c: USB UHCI at I/O 0x1820, IRQ 7
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.2 to 64
usb-uhci.c: USB UHCI at I/O 0x1840, IRQ 7
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
PCI: Setting latency timer of device 00:1d.7 to 64
ehci_hcd 00:1d.7: Intel Corp. 82801DB USB2
ehci_hcd 00:1d.7: irq 7, pci mem c8867000
usb.c: new USB bus registered, assigned bus number 3
ehci_hcd 00:1d.7: enabled 64bit PCI DMA
PCI: 00:1d.7 PCI cache line size set incorrectly (0 bytes) by BIOS/FW.
PCI: 00:1d.7 PCI cache line size corrected to 32.
ehci_hcd 00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2003-Jun-19/2.4
hub.c: USB hub found
hub.c: 6 ports detected
usbdevfs: remount parameter error
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,1), internal journal
Adding Swap: 506480k swap-space (priority -1)
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,6), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
8139too Fast Ethernet driver 0.9.26
eth0: RealTek RTL8139 Fast Ethernet at 0xc885d000, 00:40:2b:2d:99:2e, IRQ 1
eth0: Identified 8139 chip type 'RTL-8139C'
inserting floppy driver for 2.4.22-6mdk
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
hdc: attached ide-cdrom driver.
hdc: ATAPI 48X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.12
Installing knfsd (copyright (C) 1996 [EMAIL PROTECTED]).
unable to grab IRQ 1
Intel ICH soundcard not found or device busy
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 93M
agpgart: Detected an Intel(R) 845G Chipset.
agpgart: Detected 892K stolen memory.
agpgart: AGP aperture is 128M @ 0xf0000000
memory : c6eee420
memory : c6eee460
memory : c6eee4a0
[drm] AGP 0.99 Aperture @ 0xf0000000 128MB
[drm] Initialized i830 1.3.2 20021108 on minor 0
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
lp0: using parport0 (polling).
mtrr: base(0xf0020000) is not aligned on a size(0x12c000) boundary
memory : c6eee620
memory : c6eee660
memory : c6eee6a0
memory : c6eee6e0
memory : c6eee720
PCI: No IRQ known for interrupt pin A of device 00:02.0. Probably buggy MP table.
SCSI subsystem driver Revision: 1.00
VFS: Can't find ext2 filesystem on dev fd(2,0).
MSDOS FS: IO charset iso8859-15
MSDOS FS: Using codepage 850
unable to grab IRQ 1
Intel ICH soundcard not found or device busy
unable to grab IRQ 1
Intel ICH soundcard not found or device busy
unable to grab IRQ 1
Intel ICH soundcard not found or device busy
unable to grab IRQ 1
Intel ICH soundcard not found or device busy
VFS: Can't find ext2 filesystem on dev fd(2,0).
MSDOS FS: IO charset iso8859-15
MSDOS FS: Using codepage 850
unable to grab IRQ 1
Intel ICH soundcard not found or device busy
--
Configure bugmail: http://qa.mandrakesoft.com/userprefs.cgi?tab=email
------- You are receiving this mail because: -------
You are on the CC list for the bug, or are watching someone who is.
------- Reminder: -------
assigned_to: [EMAIL PROTECTED]
status: NEW
creation_date:
description:
The intel motherboards with the ICH4 controller have severe problems with kernel
2.4.19.16mdk.
a) On boot up, the message
PCI: Device 00:1f.1 not available because of resource collisions
The relevant sections from dmesg are
....
The first reference to 00:1f.1
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=2
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Using IRQ router PIIX [8086/24c0] at 00:1f.0
PCI: Found IRQ 9 for device 00:1f.1
PCI: Sharing IRQ 9 with 00:1d.2
.....Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller on PCI bus 00 dev f9
PCI: Device 00:1f.1 not available because of resource collisions
ICH4: (ide_setup_pci_device:) Could not enable device.
hda: Maxtor 91531U3, ATA DISK drive
hdb: ST340016A, ATA DISK drive
hdc: HL-DT-ST CD-ROM GCR-8520B, ATAPI CD/DVD-ROM drive
hdd: HITACHI DVD-ROM GD-2000, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
lspci gives
...
00:1f.0 ISA bridge: Intel Corp.: Unknown device 24c0 (rev 01)
00:1f.1 IDE interface: Intel Corp. 82801DB ICH4 IDE (rev 01)
00:1f.3 SMBus: Intel Corp.: Unknown device 24c3 (rev 01)
...
b) trying to start up dma does not work.
hdparm /dev/hda
/dev/hda:
multcount = 16 (on)
IO_support = 0 (default 16-bit)
unmaskirq = 0 (off)
using_dma = 0 (off)
keepsettings = 0 (off)
readonly = 0 (off)
readahead = 8 (on)
geometry = 1868/255/63, sectors = 30015216, start = 0
]>hdparm -d1 /dev/hda
/dev/hda:
setting using_dma to 1 (on)
HDIO_SET_DMA failed: Operation not permitted
using_dma = 0 (off)
The disks are very slow.
c) Sound does not work. The standare oss drivers do not load at all. -- error
that the codec cannot be intialised. The alsa drivers load fine, but again
no sound. (again using the onboard sound ICH4 sound card)
