I changed the colour scheme and was now able to see the addresses I type
into the to field of netscape.
Greg
Greg Sarsons wrote:
>
> Well I burned the beta iso's and this is how it turned out on a Abit
> kt7-raid mb with 256m and an IBM udma100 DeskStar 30g drive. Using Asus
> 7100 GeForce2 MX 32m vid card. SCSI card aha-1505.
>
> The install acted much like 7.2. I did notice on the partitioning that
> not all the directories were listed on the drop down menu. Seems to me
> that in 7.2 I could pick /boot.
>
> This install was done using expert .......
>
> Previously with 7.2 the scsi card worked on problem during the install
> setting it with aha=0x140,9,7,1. I did the same and it said it was
> located. However, when I booted up it was not present. See demg.txt
> ... said I had a conflict but this was not so before.
>
> When I run DrakConf and then exit the loose the screen and am left with
> a nice mouse pointer. Must do ctrl-alt-backspace. Same for both root
> and user.
>
> Tried deleting a user but errored with a ptmp error.
>
> Sawfish or is it Sawmill, can't remembe what the new name is, was
> installed but fails to run. It seems to start loading but then just
> sits there.
>
> Gnome does run.
>
> My RTL-8139 card works fine and nothing had to be changed.
>
> Not a big fan a watching only 3 images during the install. Made the
> install seem longer than watching each individual file go by.
>
> Noticed as well that the recpients line in netscape email is always
> blank ... can't type anything.
>
> Greg
>
> ------------------------------------------------------------------------
> Linux version 2.4.2-3mdk ([EMAIL PROTECTED]) (gcc version egcs-2.91.66
>19990314/Linux (egcs-1.1.2 release)) #1 Tue Feb 27 02:14:17 CET 2001
> BIOS-provided physical RAM map:
> BIOS-e820: 000000000009fc00 @ 0000000000000000 (usable)
> BIOS-e820: 0000000000000400 @ 000000000009fc00 (reserved)
> BIOS-e820: 0000000000010000 @ 00000000000f0000 (reserved)
> BIOS-e820: 0000000000010000 @ 00000000ffff0000 (reserved)
> BIOS-e820: 000000000fef0000 @ 0000000000100000 (usable)
> BIOS-e820: 000000000000d000 @ 000000000fff3000 (ACPI data)
> BIOS-e820: 0000000000003000 @ 000000000fff0000 (ACPI NVS)
> On node 0 totalpages: 65520
> zone(0): 4096 pages.
> zone(1): 61424 pages.
> zone(2): 0 pages.
> Kernel command line: root=/dev/hde7 vga=788
> Initializing CPU#0
> Detected 800.032 MHz processor.
> Console: colour dummy device 80x25
> Calibrating delay loop... 1595.80 BogoMIPS
> Memory: 253992k/262080k available (956k kernel code, 7700k reserved, 387k data, 224k
>init, 0k highmem)
> Dentry-cache hash table entries: 32768 (order: 6, 262144 bytes)
> Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes)
> Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
> Inode-cache hash table entries: 16384 (order: 5, 131072 bytes)
> VFS: Diskquotas version dquot_6.5.0 initialized
> CPU: Before vendor init, caps: 0183f9ff c1c7f9ff 00000000, vendor = 2
> CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
> CPU: L2 Cache: 256K (64 bytes/line)
> CPU: After vendor init, caps: 0183f9ff c1c7f9ff 00000000 00000000
> CPU: After generic, caps: 0183f9ff c1c7f9ff 00000000 00000000
> CPU: Common caps: 0183f9ff c1c7f9ff 00000000 00000000
> CPU: AMD Athlon(tm) Processor stepping 02
> Enabling fast FPU save and restore... done.
> Checking 'hlt' instruction... OK.
> POSIX conformance testing by UNIFIX
> mtrr: v1.37 (20001109) Richard Gooch ([EMAIL PROTECTED])
> mtrr: detected mtrr type: Intel
> PCI: PCI BIOS revision 2.10 entry at 0xfb430, last bus=1
> PCI: Using configuration type 1
> PCI: Probing PCI hardware
> Unknown bridge resource 0: assuming transparent
> PCI: Using IRQ router VIA [1106/0686] at 00:07.0
> isapnp: Scanning for PnP cards...
> isapnp: Card 'Adaptec AVA-1505A'
> isapnp: 1 Plug & Play card detected total
> Linux NET4.0 for Linux 2.4
> Based upon Swansea University Computer Society NET3.039
> Initializing RT netlink socket
> apm: BIOS version 1.2 Flags 0x07 (Driver version 1.14)
> Starting kswapd v1.8
> vesafb: framebuffer at 0xd8000000, mapped to 0xd0800000, size 32768k
> vesafb: mode is 800x600x16, linelength=1600, pages=3
> vesafb: protected mode interface info at c000:0ed1
> vesafb: scrolling: redraw
> vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
> Console: switching to colour frame buffer device 100x37
> fb0: VESA VGA frame buffer device
> pty: 256 Unix98 ptys configured
> block: queued sectors max/low 168712kB/56237kB, 512 slots per queue
> RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
> Uniform Multi-Platform E-IDE driver Revision: 6.31
> ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> VP_IDE: IDE controller on PCI bus 00 dev 39
> VP_IDE: chipset revision 16
> VP_IDE: not 100% native mode: will probe irqs later
> ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> VP_IDE: VIA vt82c686a (rev 22) IDE UDMA66 controller on pci00:07.1
> ide0: BM-DMA at 0xc000-0xc007, BIOS settings: hda:pio, hdb:pio
> ide1: BM-DMA at 0xc008-0xc00f, BIOS settings: hdc:pio, hdd:pio
> HPT370: IDE controller on PCI bus 00 dev 98
> PCI: Found IRQ 11 for device 00:13.0
> HPT370: chipset revision 3
> HPT370: not 100% native mode: will probe irqs later
> ide2: BM-DMA at 0xe400-0xe407, BIOS settings: hde:DMA, hdf:pio
> ide3: BM-DMA at 0xe408-0xe40f, BIOS settings: hdg:pio, hdh:pio
> hdc: CD-ROM 52X/AKH, ATAPI CD/DVD-ROM drive
> hdd: MATSHITA CD-RW CW-7585, ATAPI CD/DVD-ROM drive
> hde: IBM-DTLA-307030, ATA DISK drive
> ide1 at 0x170-0x177,0x376 on irq 15
> ide2 at 0xd400-0xd407,0xd802 on irq 11
> hde: 60036480 sectors (30739 MB) w/1916KiB Cache, CHS=59560/16/63, UDMA(100)
> hdc: ATAPI 52X CD-ROM drive, 192kB Cache, UDMA(33)
> Uniform CD-ROM driver Revision: 3.12
> hdd: ATAPI 32X CD-ROM CD-R/RW drive, 2048kB Cache, DMA
> Partition check:
> hde: [PTBL] [3737/255/63] hde1 hde2 < hde5 hde6 hde7 hde8 hde9 hde10 >
> RAMDISK: ext2 filesystem found at block 0
> RAMDISK: Loading 1500 blocks [1 disk] into ram disk...
>|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/done.
> Freeing initrd memory: 1500k freed
> Serial driver version 5.02 (2000-08-09) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ
>SERIAL_PCI ISAPNP enabled
> ttyS00 at 0x03f8 (irq = 4) is a 16550A
> ttyS01 at 0x02f8 (irq = 3) is a 16550A
> md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
> md.c: sizeof(mdp_super_t) = 4096
> autodetecting RAID arrays
> autorun ...
> ... autorun DONE.
> NET4: Linux TCP/IP 1.0 for NET4.0
> IP Protocols: ICMP, UDP, TCP, IGMP
> IP: routing cache hash table of 2048 buckets, 16Kbytes
> TCP: Hash tables configured (established 16384 bind 16384)
> Linux IP multicast router 0.06 plus PIM-SM
> IP-Config: No network devices available.
> NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
> VFS: Mounted root (ext2 filesystem).
> VFS: Mounted root (ext2 filesystem) readonly.
> change_root: old root has d_count=3
> Trying to unmount old root ... okay
> Freeing unused kernel memory: 224k freed
> Adding Swap: 257000k swap-space (priority -1)
> SCSI subsystem driver Revision: 1.00
> aha152x: BIOS test: passed, detected 1 controller(s)
> aha152x: resetting bus...
> aha152x0: vital data: rev=3, io=0x140 (0x140/0x140), irq=9, scsiid=7,
>reconnect=enabled, parity=enabled, synchronous=disabled, delay=1000, extended
>translation=disabled
> aha152x0: trying software interrupt, lost.
> aha152x0: IRQ 9 possibly wrong. Please verify.
> SCSI subsystem driver Revision: 1.00
> scsi0 : SCSI host adapter emulation for IDE ATAPI devices
> PCI: Found IRQ 10 for device 00:0d.0
> PCI: The same IRQ used for device 00:0f.0
> usb.c: registered new driver usbdevfs
> usb.c: registered new driver hub
> usb-uhci.c: $Revision: 1.251 $ time 02:23:32 Feb 27 2001
> usb-uhci.c: High bandwidth mode enabled
> PCI: Found IRQ 11 for device 00:07.2
> PCI: The same IRQ used for device 00:07.3
> usb-uhci.c: USB UHCI at I/O 0xc400, IRQ 11
> usb-uhci.c: Detected 2 ports
> usb.c: new USB bus registered, assigned bus number 1
> hub.c: USB hub found
> hub.c: 2 ports detected
> PCI: Found IRQ 11 for device 00:07.3
> PCI: The same IRQ used for device 00:07.2
> usb-uhci.c: USB UHCI at I/O 0xc800, IRQ 11
> usb-uhci.c: Detected 2 ports
> usb.c: new USB bus registered, assigned bus number 2
> hub.c: USB hub found
> hub.c: 2 ports detected
> 8139too Fast Ethernet driver 0.9.15 loaded
> PCI: Found IRQ 10 for device 00:0f.0
> PCI: The same IRQ used for device 00:0d.0
> eth0: RealTek RTL8139 Fast Ethernet at 0xd289c000, 00:48:54:8c:45:36, IRQ 10
> eth0: Identified 8139 chip type 'RTL-8139C'
> eth0: Setting 100mbps full-duplex based on auto-negotiated partner ability 41e1.
> Winbond Super-IO detection, now testing ports 3F0,370,250,4E,2E ...
> SMSC Super-IO detection, now testing Ports 2F0, 370 ...
> parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP]
> parport0: cpp_daisy: aa5500ff(98)
> parport0: assign_addrs: aa5500ff(98)
> parport0: Printer, Samsung ML-6040
> parport_pc: Via 686A parallel port: io=0x378, irq=7
> lp0: using parport0 (interrupt-driven).
> lp0: console ready
