USB does not appear to work with the EPOC D6VA motherboard under Mandrake 9.0
Beta 4 using the SMP kernel. The USB chipset is detected correctly and the
usb-uhci module seems to be happy with it, however devices attached to the
USB port are not detected (there appears to be a timeout occuring).
The usb-ohci module does not work with this chipset (unsupported). The usb
module works but has the same problems.
I've been testing using the USB hub built into my monitor (Iiyama
VisionMaster Pro453). The hub is detected correctly on another PC under
Windows-98 (my Linux machine is not dual-boot - never been contaminated by
MS).
Attached are output from "dmesg", "lspci -vv" and "lspcidrake -v".
Note that a similar problem existed under 8.2.
agpgart : VIA Technologies|VT82C691 [Apollo PRO] [BRIDGE_HOST] (vendor:1106
device:0691)
unknown : VIA Technologies|VT82C598 [Apollo MVP3 AGP] [BRIDGE_PCI]
(vendor:1106 device:8598)
unknown : VIA Technologies|VT82C596 ISA [Apollo PRO] [BRIDGE_ISA] (vendor:1106
device:0596 subv:1106 subd:0000)
unknown : VIA Technologies|VT82C586 IDE [Apollo] [STORAGE_IDE] (vendor:1106
device:0571)
usb-uhci : VIA Technologies|VT82C586B USB [SERIAL_USB] (vendor:1106 device:3038
subv:0925 subd:1234)
unknown : VIA Technologies Inc|Power Management Controller [BRIDGE_OTHER]
(vendor:1106 device:3050)
snd-emu10k1 : Creative Labs|SB Live! (audio) [MULTIMEDIA_AUDIO] (vendor:1102
device:0002 subv:1102 subd:8061)
emu10k1-gp : Creative Labs|SB Live! (joystick) [INPUT_OTHER] (vendor:1102
device:7002 subv:1102 subd:0020)
8139too : D-Link Inc|DFE 538 TX [NETWORK_ETHERNET] (vendor:1186 device:1300)
hptraid : Triones|HPT366 [STORAGE_OTHER] (vendor:1103 device:0004 subv:1103
subd:0001)
Card:ATI Radeon : ATI|Radeon QD [DISPLAY_VGA] (vendor:1002 device:5144 subv:1002
subd:001a)
unknown : Virtual|Hub [] (vendor:0000 device:0000)
00:00.0 Host bridge: VIA Technologies, Inc. VT82C693A/694x [Apollo PRO133x] (rev c4)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort+ >SERR- <PERR-
Latency: 8
Region 0: Memory at d8000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2,x4
Command: RQ=0 SBA+ AGP+ 64bit- FW- Rate=x1
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598/694x [Apollo MVP3/Pro133x AGP]
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort+ >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00009000-00009fff
Memory behind bridge: dc000000-ddffffff
Prefetchable memory behind bridge: d0000000-d7ffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.0 ISA bridge: VIA Technologies, Inc. VT82C596 ISA [Mobile South] (rev 23)
Subsystem: VIA Technologies, Inc. VT82C596/A/B PCI to ISA Bridge
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+
SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
00:07.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 10) (prog-if 8a
[Master SecP PriP])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at a000 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.2 USB Controller: VIA Technologies, Inc. USB (rev 11) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 19
Region 4: I/O ports at a400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.3 Bridge: VIA Technologies, Inc. VT82C596 Power Management (rev 30)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
00:08.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev 07)
Subsystem: Creative Labs SBLive! Player 5.1
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 5000ns max)
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at a800 [size=32]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:08.1 Input device controller: Creative Labs SB Live! MIDI/Game Port (rev 07)
Subsystem: Creative Labs Gameport Joystick
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 32
Region 0: I/O ports at ac00 [size=8]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:09.0 Ethernet controller: D-Link System Inc RTL8139 Ethernet (rev 10)
Subsystem: D-Link System Inc RTL8139 Ethernet
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 32 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at b000 [size=256]
Region 1: Memory at df000000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0b.0 Unknown mass storage controller: Triones Technologies, Inc. HPT366 / HPT370
(rev 04)
Subsystem: Triones Technologies, Inc.: Unknown device 0001
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 120 (2000ns min, 2000ns max), cache line size 08
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at b400 [size=8]
Region 1: I/O ports at b800 [size=4]
Region 2: I/O ports at bc00 [size=8]
Region 3: I/O ports at c000 [size=4]
Region 4: I/O ports at c400 [size=256]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 VGA compatible controller: ATI Technologies Inc Radeon QD (prog-if 00 [VGA])
Subsystem: ATI Technologies Inc Radeon 7000/Radeon
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+
SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 32 (2000ns min), cache line size 08
Interrupt: pin A routed to IRQ 16
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at 9000 [size=256]
Region 2: Memory at dd000000 (32-bit, non-prefetchable) [size=512K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [58] AGP version 2.0
Status: RQ=47 SBA+ 64bit- FW- Rate=x1,x2,x4
Command: RQ=31 SBA+ AGP+ 64bit- FW- Rate=x1
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Linux version 2.4.19-5mdksmp ([EMAIL PROTECTED]) (gcc version 3.2 (Mandrake
Linux 9.0 3.2-1mdk)) #1 SMP Fri Aug 23 20:03:04 CEST 2002
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000002fff0000 (usable)
BIOS-e820: 000000002fff0000 - 000000002fff3000 (ACPI NVS)
BIOS-e820: 000000002fff3000 - 0000000030000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
767MB LOWMEM available.
found SMP MP-table at 000f5a40
hm, page 000f5000 reserved twice.
hm, page 000f6000 reserved twice.
hm, page 000f1000 reserved twice.
hm, page 000f2000 reserved twice.
Advanced speculative caching feature not present
On node 0 totalpages: 196592
zone(0): 4096 pages.
zone(1): 192496 pages.
zone(2): 0 pages.
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: OEM00000 Product ID: PROD00000000 APIC at: 0xFEE00000
Processor #0 Pentium(tm) Pro APIC version 17
Processor #1 Pentium(tm) Pro APIC version 17
I/O APIC #2 Version 17 at 0xFEC00000.
Processors: 2
Kernel command line: root=/dev/hda12 devfs=mount hdc=ide-scsi
ide_setup: hdc=ide-scsi
Initializing CPU#0
Detected 1002.286 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 1998.84 BogoMIPS
Memory: 775008k/786368k available (1258k kernel code, 10972k reserved, 463k data, 140k
init, 0k highmem)
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode cache hash table entries: 65536 (order: 7, 524288 bytes)
Mount-cache hash table entries: 16384 (order: 5, 131072 bytes)
Buffer-cache hash table entries: 65536 (order: 6, 262144 bytes)
Page-cache hash table entries: 262144 (order: 8, 1048576 bytes)
CPU: Before vendor init, caps: 0387fbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After vendor init, caps: 0387fbff 00000000 00000000 00000000
CPU serial number disabled.
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch ([EMAIL PROTECTED])
mtrr: detected mtrr type: Intel
CPU: Before vendor init, caps: 0383fbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After vendor init, caps: 0383fbff 00000000 00000000 00000000
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
CPU0: Intel Pentium III (Coppermine) stepping 0a
per-CPU timeslice cutoff: 731.04 usecs.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Booting processor 1/1 eip 2000
Initializing CPU#1
masked ExtINT on CPU#1
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 1998.84 BogoMIPS
CPU: Before vendor init, caps: 0387fbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After vendor init, caps: 0387fbff 00000000 00000000 00000000
CPU serial number disabled.
Intel machine check reporting enabled on CPU#1.
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
CPU1: Intel Pentium III (Coppermine) stepping 0a
Total of 2 processors activated (3997.69 BogoMIPS).
ENABLING IO-APIC IRQs
Setting 2 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 2 ... ok.
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-5, 2-10, 2-11, 2-18, 2-20, 2-21, 2-22, 2-23 not connected.
..TIMER: vector=0x31 pin1=2 pin2=0
number of MP IRQ sources: 19.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
.... register #01: 00170011
....... : max redirection entries: 0017
....... : PRQ implemented: 0
....... : IO APIC version: 0011
.... register #02: 00000000
....... : arbitration: 00
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 003 03 0 0 0 0 0 1 1 39
02 003 03 0 0 0 0 0 1 1 31
03 003 03 0 0 0 0 0 1 1 41
04 003 03 0 0 0 0 0 1 1 49
05 000 00 1 0 0 0 0 0 0 00
06 003 03 0 0 0 0 0 1 1 51
07 003 03 0 0 0 0 0 1 1 59
08 003 03 0 0 0 0 0 1 1 61
09 003 03 0 0 0 0 0 1 1 69
0a 000 00 1 0 0 0 0 0 0 00
0b 000 00 1 0 0 0 0 0 0 00
0c 003 03 0 0 0 0 0 1 1 71
0d 003 03 0 0 0 0 0 1 1 79
0e 003 03 0 0 0 0 0 1 1 81
0f 003 03 0 0 0 0 0 1 1 89
10 003 03 1 1 0 1 0 1 1 91
11 003 03 1 1 0 1 0 1 1 99
12 000 00 1 0 0 0 0 0 0 00
13 003 03 1 1 0 1 0 1 1 A1
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 000 00 1 0 0 0 0 0 0 00
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ19 -> 0:19
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1002.1760 MHz.
..... host bus clock speed is 133.6233 MHz.
cpu: 0, clocks: 1336233, slice: 445411
CPU0<T0:1336224,T1:890800,D:13,S:445411,C:1336233>
cpu: 1, clocks: 1336233, slice: 445411
CPU1<T0:1336224,T1:445392,D:10,S:445411,C:1336233>
checking TSC synchronization across CPUs: passed.
Waiting on wait_init_idle (map = 0x2)
All processors have done init_idle
mtrr: your CPUs had inconsistent variable MTRR settings
mtrr: probably your BIOS does not setup all CPUs
PCI: PCI BIOS revision 2.10 entry at 0xfb350, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Using IRQ router VIA [1106/0596] at 00:07.0
PCI->APIC IRQ transform: (B0,I7,P3) -> 19
PCI->APIC IRQ transform: (B0,I8,P0) -> 16
PCI->APIC IRQ transform: (B0,I9,P0) -> 17
PCI->APIC IRQ transform: (B0,I11,P0) -> 16
PCI->APIC IRQ transform: (B1,I0,P0) -> 16
Activating ISA DMA hang workarounds.
PCI: Via IRQ fixup for 00:07.2, from 5 to 3
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16)
apm: disabled - APM is not SMP safe.
Starting kswapd
VFS: Diskquotas version dquot_6.5.0 initialized
devfs: v1.12a (20020514) Richard Gooch ([EMAIL PROTECTED])
devfs: boot_options: 0x1
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ
SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller on PCI bus 00 dev 39
VP_IDE: chipset revision 16
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt82c596b (rev 23) IDE UDMA66 controller on pci00:07.1
ide0: BM-DMA at 0xa000-0xa007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xa008-0xa00f, BIOS settings: hdc:DMA, hdd:pio
HPT370A: IDE controller on PCI bus 00 dev 58
HPT370A: chipset revision 4
HPT370A: not 100% native mode: will probe irqs later
HPT370: using 33MHz PCI clock
ide2: BM-DMA at 0xc400-0xc407, BIOS settings: hde:DMA, hdf:pio
ide3: BM-DMA at 0xc408-0xc40f, BIOS settings: hdg:DMA, hdh:pio
hda: IC35L040AVER07-0, ATA DISK drive
hdc: RICOH DVD/CDRW MP9120, ATAPI CD/DVD-ROM drive
hde: IC35L040AVER07-0, ATA DISK drive
hdg: IC35L040AVER07-0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
ide2 at 0xb400-0xb407,0xb802 on irq 16
ide3 at 0xbc00-0xbc07,0xc002 on irq 16
hda: 80418240 sectors (41174 MB) w/1916KiB Cache, CHS=5005/255/63, UDMA(66)
hde: 80418240 sectors (41174 MB) w/1916KiB Cache, CHS=79780/16/63, UDMA(44)
hdg: 80418240 sectors (41174 MB) w/1916KiB Cache, CHS=79780/16/63, UDMA(44)
Partition check:
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3 p4 < p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 >
/dev/ide/host2/bus0/target0/lun0: p1 p2
/dev/ide/host2/bus1/target0/lun0: p1 p2
RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
[events: 0000006a]
[events: 0000006a]
md: autorun ...
md: considering ide/host2/bus1/target0/lun0/part2 ...
md: adding ide/host2/bus1/target0/lun0/part2 ...
md: adding ide/host2/bus0/target0/lun0/part2 ...
md: created md0
md: bind<ide/host2/bus0/target0/lun0/part2,1>
md: bind<ide/host2/bus1/target0/lun0/part2,2>
md: running: <ide/host2/bus1/target0/lun0/part2><ide/host2/bus0/target0/lun0/part2>
md: ide/host2/bus1/target0/lun0/part2's event counter: 0000006a
md: ide/host2/bus0/target0/lun0/part2's event counter: 0000006a
kmod: failed to exec /sbin/modprobe -s -k md-personality-2, errno = 2
md: personality 2 is not loaded!
md :do_md_run() returned -22
md: md0 stopped.
md: unbind<ide/host2/bus1/target0/lun0/part2,1>
md: export_rdev(ide/host2/bus1/target0/lun0/part2)
md: unbind<ide/host2/bus0/target0/lun0/part2,0>
md: export_rdev(ide/host2/bus0/target0/lun0/part2)
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 145k freed
VFS: Mounted root (ext2 filesystem).
Mounted devfs on /dev
reiserfs: checking transaction log (device 03:0c) ...
Using r5 hash to sort names
ReiserFS version 3.6.25
Mounted devfs on /dev
Freeing unused kernel memory: 140k freed
Real Time Clock Driver v1.10e
Adding Swap: 1052248k swap-space (priority -1)
Adding Swap: 1048784k swap-space (priority -2)
Adding Swap: 1048784k swap-space (priority -3)
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: RICOH Model: DVD/CDRW MP9120 Rev: 1.20
Type: CD-ROM ANSI SCSI revision: 02
[events: 0000006a]
[events: 0000006a]
md: autorun ...
md: considering ide/host2/bus0/target0/lun0/part2 ...
md: adding ide/host2/bus0/target0/lun0/part2 ...
md: adding ide/host2/bus1/target0/lun0/part2 ...
md: created md0
md: bind<ide/host2/bus1/target0/lun0/part2,1>
md: bind<ide/host2/bus0/target0/lun0/part2,2>
md: running: <ide/host2/bus0/target0/lun0/part2><ide/host2/bus1/target0/lun0/part2>
md: ide/host2/bus0/target0/lun0/part2's event counter: 0000006a
md: ide/host2/bus1/target0/lun0/part2's event counter: 0000006a
md: raid0 personality registered as nr 2
md0: max total readahead window set to 512k
md0: 2 data-disks, max readahead per data-disk: 256k
raid0: looking at ide/host2/bus0/target0/lun0/part2
raid0: comparing ide/host2/bus0/target0/lun0/part2(39160192) with
ide/host2/bus0/target0/lun0/part2(39160192)
raid0: END
raid0: ==> UNIQUE
raid0: 1 zones
raid0: looking at ide/host2/bus1/target0/lun0/part2
raid0: comparing ide/host2/bus1/target0/lun0/part2(39160192) with
ide/host2/bus0/target0/lun0/part2(39160192)
raid0: EQUAL
raid0: FINAL 1 zones
raid0: zone 0
raid0: checking ide/host2/bus0/target0/lun0/part2 ... contained as device 0
(39160192) is smallest!.
raid0: checking ide/host2/bus1/target0/lun0/part2 ... contained as device 1
raid0: zone->nb_dev: 2, size: 78320384
raid0: current zone offset: 39160192
raid0: done.
raid0 : md_size is 78320384 blocks.
raid0 : conf->smallest->size is 78320384 blocks.
raid0 : nb_zone is 1.
raid0 : Allocating 8 bytes for hash.
md: updating md0 RAID superblock on device
md: ide/host2/bus0/target0/lun0/part2 [events: 0000006b]<6>(write)
ide/host2/bus0/target0/lun0/part2's sb offset: 39160192
md: ide/host2/bus1/target0/lun0/part2 [events: 0000006b]<6>(write)
ide/host2/bus1/target0/lun0/part2's sb offset: 39160192
md: ... autorun DONE.
hdc: DMA disabled
8139too Fast Ethernet driver 0.9.25
eth0: D-Link DFE-538TX (RealTek RTL8139) at 0xf0aa5000, 00:50:ba:4e:18:53, IRQ 17
eth0: Identified 8139 chip type 'RTL-8139C'
eth0: Setting 100mbps full-duplex based on auto-negotiated partner ability 45e1.
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 20:35:20 Aug 23 2002
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: USB UHCI at I/O 0xa400, IRQ 19
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usbdevfs: remount parameter error
mice: PS/2 mouse device common for all mice
hub.c: USB new device connect on bus1/2, assigned device number 2
usb_control/bulk_msg: timeout
usb.c: USB device not accepting new address=2 (error=-110)
hub.c: USB new device connect on bus1/2, assigned device number 3
usb_control/bulk_msg: timeout
usb.c: USB device not accepting new address=3 (error=-110)
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 690M
agpgart: Detected Via Apollo Pro chipset
agpgart: AGP aperture is 64M @ 0xd8000000
[drm] AGP 0.99 on VIA Apollo Pro @ 0xd8000000 64MB
[drm] Initialized radeon 1.2.0 20011231 on minor 0
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
parport0: irq 7 detected
lp0: using parport0 (polling).
Creative EMU10K1 PCI Audio Driver, version 0.19, 20:33:18 Aug 23 2002
emu10k1: EMU10K1 rev 7 model 0x8061 found, IO at 0xa800-0xa81f, IRQ 16
ac97_codec: AC97 Audio codec, id: 0x8384:0x7608 (SigmaTel STAC9708)
emu10k1: SBLive! 5.1 card detected
inserting floppy driver for 2.4.19-5mdksmp
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 2, lun 0
sr0: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.12
