Hi, Please see below.
Jason Wang BeiJing Technology Development Center Advanced Micro Devices (AMD) ________________________________ From: [email protected] [mailto:[email protected]] On Behalf Of Dan Lykowski Sent: Saturday, January 17, 2009 2:59 PM To: [email protected]; Peter Stuge Subject: Re: [coreboot] FILO and SATA on 690/600 Peter, I will test it when I get in to work on Monday. I was able to get a HDD to be detected. My SATA flash is still being stubborn. Here is my log: (Without Peters Patch) boot eax = 0x2badb002 boot ebx = 0xf3400 boot arg = 0xf3400 Current location: 0x100000-0x49e117 Relocating to 0x37c61000-0x37fff117... ok 00:13.0 4387:1002.0 OHCI controller 00:13.1 4388:1002.1 OHCI controller 00:13.2 4389:1002.2 OHCI controller 00:13.3 438a:1002.3 OHCI controller 00:13.4 438b:1002.4 OHCI controller 00:13.5 4386:1002.5 EHCI controller Not supported. ERROR: No such CMOS option (boot_devices) Press <Enter> for default menu.lst (hda1:/boot/filo/menu.lst), or <Esc> for prompt... menu: hda1:/boot/filo/menu.lst dev=hda1, path=/boot/filo/default Scanning for: SATA ... found PCI IDE controller 1002:4380 prog_if=0x8f primary channel: native PCI mode cmd_base=0x3020 ctrl_base=0x3060 init_controller: drive 0 Waiting for ide0 to become ready for reset... ok Resetting ide0... ok Testing for hda ProbIDE: status=0x58, err=0x0 Testing for hda ProbIDE: status=0x51, err=0x4 MASTER CHECK: master no /* slave */ -- drive is 0 NO MASTER -- check slave! Testing for hda ProbLBA mode, sectors=156301488 Init device params... ok hda: LBA 80GB: WDC WD800JD-22JNA0 SLAVE ONLY CHECK: slave yes Partition 1 start 64260 length 16787925 Unknown filesystem type. [Jason, Wang] if seems that filo can not detect the the filesystem type. Did hda1 is an ext2 or ext3 filesystem Change the filo config.h MENULST_FILE to the correct path of your linux boot path. And try again dev=hda1, path=/boot/filo/menu.lst already open Could not open menu.lst file 'hda1:/boot/filo/menu.lst'. Entering command line. [Jason, Wang] please make sure that the /boot/filo/menu.lst exist Thanks, Dan Lykowski --- On Sat, 1/17/09, Peter Stuge <[email protected]> wrote: From: Peter Stuge <[email protected]> Subject: Re: [coreboot] FILO and SATA on 690/600 To: [email protected] Date: Saturday, January 17, 2009, 1:09 AM -----Inline Attachment Follows----- Dan Lykowski wrote: > Has anyone been able to boot a SATA drive using FILO on a 690/600 > platform? > I keep getting IDE timeouts on detection. I would be interested in debug output from filo-0.5, e.g. r52, with http://stuge.se/filo.r52.ide_ext2_pio4_debug6.patch applied and both DEBUG_PCI = 1 and DEBUG_IDE = 1 in Config. Please also set USE_GRUB = 0 to make the interface easier to work with. //Peter -- coreboot mailing list: [email protected] http://www.coreboot.org/mailman/listinfo/coreboot
-- coreboot mailing list: [email protected] http://www.coreboot.org/mailman/listinfo/coreboot
