There is a Lanner FW-7573 platform based on the Intel Rangeley Atom C2000
series processor.
To work with the Serial port in this platform, the NUVOTON NCT6776F chip is
connected via the LPC bus to the processor.
I just can’t get Serial port working for debuging. I take as a basis intel
littleplains board. I tried to add NCT6776F support following the example of
other boards - without success. There is no output to the console, and in
Linux, the superiotool program does not see the NCT6776F.
On the official version of the BIOS I loaded linux OS and took a dump.
(superiotool r => Found Nuvoton NCT6776F/D (C) (id=0xc333) at 0x4e) )
How to add NUVOTON NCT6776F support with serial port logic enabled ???
in devicetree.cb I add:
device pci 1f.0 on # LPC bridge
chip superio/nuvoton/nct6776
device pnp 4e.0 off end # Floppy
device pnp 4e.1 off end #
Parallel port
device pnp 4e.2 on # COM1
io 0x60 = 0x3f8
irq 0x70 = 4
end
device pnp 4e.3 off end # COM2,
IR
device pnp 4e.5 off end #
Keyboard
device pnp 4e.6 off end # CIR
device pnp 4e.7 off end # GPIO6
device pnp 4e.107 off end # GPIO7
device pnp 4e.207 off end # GPIO8
device pnp 4e.307 off end # GPIO9
device pnp 4e.8 off end # WDT
device pnp 4e.108 off end # GPIO0
device pnp 4e.208 off end # GPIOA
device pnp 4e.308 off end #
GPIOBASE
device pnp 4e.109 off end # GPIO1
device pnp 4e.209 off end # GPIO2
device pnp 4e.309 off end # GPIO3
device pnp 4e.409 off end # GPIO4
device pnp 4e.509 off end # GPIO5
device pnp 4e.609 off end # GPIO6
device pnp 4e.709 off end # GPIO7
device pnp 4e.a on end # ACPI
device pnp 4e.b off end # HWM,
front pannel LED
device pnp 4e.d off end # VID
device pnp 4e.e off end # CIR
WAKE-UP
device pnp 4e.f off end # GPIO
device pnp 4e.14 off end # SVID
device pnp 4e.16 off end # Deep
sleep
device pnp 4e.17 off end # GPIOA
end
end # LPC bridge
In superio.asl i add:
#undef SUPERIO_DEV
#undef SUPERIO_PNP_BASE
#define SUPERIO_DEV SIO0
#define SUPERIO_PNP_BASE 0x4e
#define NCT6776_SHOW_PP
#define NCT6776_SHOW_SP1
#define NCT6776_SHOW_KBC
#define NCT6776_SHOW_HWM
#define NCT6776_SHOW_GPIO
#include <superio/nuvoton/nct6776/acpi/superio.asl>
in romstage.c add function mainboard_config_superio:
void mainboard_config_superio(void)
{
/* Enable UART */
nuvoton_pnp_enter_conf_state(GLOBAL_DEV);
/* Select SIO pin states. */ As in Dump........
pnp_write_config(GLOBAL_DEV, 0x13, 0xff);
pnp_write_config(GLOBAL_DEV, 0x14, 0xff);
pnp_write_config(GLOBAL_DEV, 0x1b, 0x53);
pnp_write_config(GLOBAL_DEV, 0x1c, 0x80);
pnp_write_config(GLOBAL_DEV, 0x24, 0x24);
pnp_write_config(GLOBAL_DEV, 0x27, 0xc0);
pnp_write_config(GLOBAL_DEV, 0x2b, 0x03);
pnp_write_config(GLOBAL_DEV, 0x2a, 0x00);
pnp_write_config(GLOBAL_DEV, 0x2c, 0x80);
/* Power RAM in S3. */
//pnp_set_logical_device(ACPI_DEV);
//pnp_write_config(ACPI_DEV, 0xe4, 0x10);
pnp_set_logical_device(SERIAL_DEV);
nuvoton_pnp_exit_conf_state(GLOBAL_DEV);
nuvoton_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
}
_______________________________________________
coreboot mailing list -- [email protected]
To unsubscribe send an email to [email protected]
