Hi,
Thank you Swami for your help.
I now have a 3com dongle (3CRUSB10075) working on the DVEVM, but I had to use a
USB1.1 hub to get it working and I can only get 11Mbit connection.
I have updated the kit/software to 1.20, and I have tried the following drivers:
1. ZD1211LnxDrv_2_15_0_0 without the patch
(http://linux.omap.com/pipermail/davinci-linux-open-source/2007-February/002478.html)
2. ZD1211LnxDrv_2_15_0_0 with the patch
3. ZD1211LnxDrv_2_22_0_0
All three fail without the USB1.1 hub.
Is there any way I can get the dongle to work in High Speed (USB 2.0) ?
Or how can I set the USB host to USB1.1 mode so I don't have to use a hub?
I am attaching outputs from the above three cases, and a fourth:
4. ZD1211LnxDrv_2_15_0_0 with the patch and USB 1.1 hub (working)
Regards,
Fredrik Redgård
From: Subbrathnam, Swaminathan [mailto:[EMAIL PROTECTED]
Sent: den 3 mars 2008 14:50
To: Fredrik Redgård; [email protected]
Subject: RE: USB WIFI
Fredrik,
You would have to apply the latest patches on the MVL401 base kernel to get the
USB functionality to support USB WiFi dongle.
Many customers have used the Zydas 1211b based WiFi dongle with DaVinci USB.
regards
swami
________________________________
From: [EMAIL PROTECTED] on behalf of Fredrik Redgård
Sent: Mon 3/3/2008 7:09 PM
To: davinci linux open source ([email protected])
Subject: USB WIFI
Hello,
I want to use WiFi with the DVEVM6446 kit, preferably using a USB WIFI Dongle.
Has anyone successfully used wifi with this evaluation kit?
I have found a lot of messages from people who have had problems with USB and
wifi with davinci, but I haven't seen any solutions.
Looking at the version of montavista linux that comes with the kit
(2.6.10_mvl401), it doesn't seem to have support for wireless networking?
Regards,
Fredrik Redgård
_______________________________________________
Davinci-linux-open-source mailing list
[email protected]
http://linux.davincidsp.com/mailman/listinfo/davinci-linux-open-source
[EMAIL PROTECTED]:/nfs# insmod zd1211b_22.ko
_____ ____ _ ____
|__ / _| _ \ / \ / ___|
/ / | | | | | |/ _ \ \___ \
/ /| |_| | |_| / ___ \ ___) |
/____\__, |____/_/ \_\____/
|___/
ZD1211B - version 2.22.0.0-development
usbcore: registered new driver zd1211b
[EMAIL PROTECTED]:/nfs# usb 1-1: new high speed USB device using musb_hdrc and
address 2
vendor_id = 0ace
product_id = 1215
USB 2.0 Host
Release Ver = 4810
EEPORM Ver = 4810
##### Warning! ####
usb_control_msg doesn't send all data out
You need to decrease the message amount in each send
##### Warning! ####
usb_control_msg doesn't send all data out
You need to decrease the message amount in each send
Finsih download Firmware. Ready to reboot
usb 1-1: khubd timed out on ep0out
usb_set_configuration() failed
zd1211b: probe of 1-1:1.0 failed with error -5
[EMAIL PROTECTED]:/nfs# insmod zd1211b_orig.ko
_____ ____ _ ____
|__ / _| _ \ / \ / ___|
/ / | | | | | |/ _ \ \___ \
/ /| |_| | |_| / ___ \ ___) |
/____\__, |____/_/ \_\____/
|___/
ZD1211B - version 2.15.0.0
usbcore: registered new driver zd1211b
[EMAIL PROTECTED]:/nfs# usb 1-1: new high speed USB device using musb_hdrc and
address 4
vendor_id = 0ace
product_id = 1215
USB 2.0 Host
Release Ver = 4810
EEPORM Ver = 4810
##### Warning! ####
usb_control_msg doesn't send all data out
You need to decrease the message amount in each send
##### Warning! ####
usb_control_msg doesn't send all data out
You need to decrease the message amount in each send
Finsih download Firmware. Ready to reboot
[EMAIL PROTECTED]:/nfs# insmod zd1211b_patch.ko
_____ ____ _ ____
|__ / _| _ \ / \ / ___|
/ / | | | | | |/ _ \ \___ \
/ /| |_| | |_| / ___ \ ___) |
/____\__, |____/_/ \_\____/
|___/
ZD1211B - version 2.15.0.0
usbcore: registered new driver zd1211b
[EMAIL PROTECTED]:/nfs# usb 1-1: new high speed USB device using musb_hdrc and
address 5
vendor_id = 0ace
product_id = 1215
USB 2.0 Host
Release Ver = 4810
EEPORM Ver = 4810
Finsih download Firmware. Ready to reboot
zd1211_USB_PACKAGE_READ_REGISTER: warning, restarting INT EP
zd1211_USB_PACKAGE_READ_REGISTER: warning, restarting INT EP
zd1211_readl retry OK
zd1211_USB_PACKAGE_READ_REGISTER: warning, restarting INT EP
zd1211_readl retry OK
zd1211_USB_PACKAGE_READ_REGISTER: warning, restarting INT EP
zd1211_readl retry OK
PA type: 0
RFMD RF
zd1211_USB_PACKAGE_READ_REGISTER: warning, restarting INT EP
zd1211_readl retry OK
AllowedChannel = 000107ff
Region:0
zd1211_USB_PACKAGE_READ_REGISTER: warning, restarting INT EP
zd1211_readl retry OK
[EMAIL PROTECTED]:/nfs# insmod zd1211b_patch.ko
_____ ____ _ ____
|__ / _| _ \ / \ / ___|
/ / | | | | | |/ _ \ \___ \
/ /| |_| | |_| / ___ \ ___) |
/____\__, |____/_/ \_\____/
|___/
ZD1211B - version 2.15.0.0
usbcore: registered new driver zd1211b
[EMAIL PROTECTED]:/nfs# usb 1-1: new full speed USB device using musb_hdrc and
address 5
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
usb 1-1.2: new full speed USB device using musb_hdrc and address 6
usb 1-1.2: not running at top speed; connect to a high speed hub
vendor_id = 0ace
product_id = 1215
USB 1.1 Host
Release Ver = 4810
EEPORM Ver = 4810
Finsih download Firmware. Ready to reboot
PA type: 0
PHYNEWLayout = 1
Airoha AL2230S_RF
AllowedChannel = 000107ff
Region:16
_______________________________________________
Davinci-linux-open-source mailing list
[email protected]
http://linux.davincidsp.com/mailman/listinfo/davinci-linux-open-source
