VPFE_STD_AUTO means driver is using the sense capabilities of TVP5146 to detect the standard. If this is failing, check if the video source is connected to either the S-Video or Composite video input.
________________________________ From: Pepe Sanchez [mailto:[EMAIL PROTECTED] Sent: Thursday, March 27, 2008 5:43 AM To: Jammy Dane Cc: huahua5; Karicheri, Muralidharan; Diego Dompe; [EMAIL PROTECTED] Subject: Re: RE: PAL and NTSC problem on dm355 Any advance about this thread? I've tried to change height parameter from 480 (NTSC) to 576 (PAL) in main.c but it doesn't work. I think the problem is in this part of capture.c: /* Auto detect PAL or NTSC using the capture driver as sanity check */ std = VPFE_STD_AUTO; if(ioctl(fd, VIDIOC_S_STD, &std) == -1) { ERR("VIDIOC_S_STD (auto) failed on %s (%s)\n", V4L2_DEVICE, strerror(errno)); return FAILURE; } I don't know where check if VPFE_STD_AUTO is work in proper way. Regards. 2008/3/27, Jammy Dane <[EMAIL PROTECTED]>: 1 to huahua5: Can you give me the detail of "modify the framebuffer driver to support run-time switch between NTSC and PAL."? 2 to all i have tried to modify the bootargs following by what Karicheri said but it did not work? what's wrong? ----- Original Message ----- From: huahua5 <mailto:[EMAIL PROTECTED]> To: Karicheri, Muralidharan <mailto:[EMAIL PROTECTED]> ; Karicheri, Muralidharan <mailto:[EMAIL PROTECTED]> ; Jammy Dane <mailto:[EMAIL PROTECTED]> ; Diego Dompe <mailto:[EMAIL PROTECTED]> Cc: [EMAIL PROTECTED] Sent: Thursday, March 27, 2008 10:17 AM Subject: Re: RE: PAL and NTSC problem on dm355 you can resolve this problem as followed: 1,DM355 board has a switch used for PAL & NTSC option.u-boot will check the switch and transfer it to framebuffer driver.it is ugly. 2,modify the framebuffer driver to support run-time switch between NTSC and PAL. I have try 2,but when I switch from NTSC to PAL,it will make the dsplinkk module oops.switch from PAL to NTSC is ok.anyone has comments? in a word, the display mode depend on the camera mode,and only the display mode can be changed by software,the camera mode is decided by your hardware. ________________________________ huahua5 2008-03-27 ________________________________ 发件人： Karicheri, Muralidharan 发送时间： 2008-03-27 03:27:23 收件人： Karicheri, Muralidharan; Jammy Dane; Diego Dompe 抄送： [email protected] 主题： RE: PAL and NTSC problem on dm355 I missed one information. Did you set the bootargs correctly ? The jumper setting is read by the bootloader and is updated in the videostd environment variable. Now for the driver to use this variable, bootargs need to have the following settings. video=dm355fb:output=\$(videostd) Now based on Jumper settings, following will be passed to kernel (and to driver) video=dm355fb:output=pal or video=dm355fb:output=ntsc depending on the jumper settings ________________________________ From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Karicheri, Muralidharan Sent: Wednesday, March 26, 2008 12:56 PM To: Jammy Dane; Diego Dompe Cc: [email protected] Subject: RE: PAL and NTSC problem on dm355 It means, the linux driver is detecting it as PAL, but application is trying to select a NTSC camera. Check the demo code to see why it is selecting a NTSC camera and fix it. ________________________________ From: Jammy Dane [mailto:[EMAIL PROTECTED] Sent: Wednesday, March 26, 2008 12:02 PM To: Diego Dompe; Karicheri, Muralidharan Cc: [email protected] Subject: Re: PAL and NTSC problem on dm355 Hi, what problem i mentioned is that when i connect the pal camera to the evm and run the encode or encodedecode demo supplied by the DVSDK, it said: PAL camera connect but NTSC camera selected. it did not work though i have set the J1 to select the pal camera. what 's wrong with it ? can you say more? Regards Jammy ----- Original Message ----- From: Karicheri, Muralidharan <mailto:[EMAIL PROTECTED]> To: Diego Dompe <mailto:[EMAIL PROTECTED]> ; Jammy Dane <mailto:[EMAIL PROTECTED]> Cc: [email protected] Sent: Wednesday, March 26, 2008 9:24 PM Subject: RE: PAL and NTSC problem on dm355 Hi, TVP5146 has autodetect feature. To turn it on, you need to invoke a S_STD ioctl to the V4L2 capture driver (choose TVP5146 as the capture driver in bootargs) which will detect PAL standard if you feed a PAL source output to the composite/S-video input of the tvp. Hope this helps. Murali From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Diego Dompe Sent: Wednesday, March 26, 2008 8:36 AM To: Jammy Dane Cc: [email protected] Subject: Re: PAL and NTSC problem on dm355 Hi, The framebuffer driver should support PAL output (but I don't have hardware to verify it). Could you elaborate on the problem you have? Do you mean programming the video capture driver to capture on PAL? The video capture driver works over raw YUV data received on digital format from the video codec used on the DM355 EVM (TVP5146), so its the TVP how is responsible to encode from PAL signal, so is probably a matter of performing an ioctl over the video driver to ask the driver to signal the CODEC the PAL format over the i2c. Let me know if this is what you are looking for, I'm not at my desktop right now so I can't grep on the files. Diego Dompe RidgeRun Engineering On Mar 26, 2008, at 6:12 AM, Jammy Dane wrote: Hi,all I am developing the dm355 evm, and as u knows, the dm355 evm does not support pal camera, how should we do for supporting the pal standard. can u give me some advice? thanks Jammy Dane _______________________________________________ Davinci-linux-open-source mailing list [email protected] http://linux.davincidsp.com/mailman/listinfo/davinci-linux-open-source _______________________________________________ Davinci-linux-open-source mailing list [email protected] http://linux.davincidsp.com/mailman/listinfo/davinci-linux-open-source
_______________________________________________ Davinci-linux-open-source mailing list [email protected] http://linux.davincidsp.com/mailman/listinfo/davinci-linux-open-source
