Add platform devices for use by isp116x-hcd driver for EtherNAT and NetUSBee
USB functions.
Register definitions thanks to David Galvez <[email protected]>

Signed-off-by: Michael Schmitz <[email protected]>
---
 arch/m68k/atari/config.c |  131 ++++++++++++++++++++++++++++++++++++++++++++--
 1 files changed, 126 insertions(+), 5 deletions(-)

diff --git a/arch/m68k/atari/config.c b/arch/m68k/atari/config.c
index 19114f5..0137fa5 100644
--- a/arch/m68k/atari/config.c
+++ b/arch/m68k/atari/config.c
@@ -32,6 +32,7 @@
 #include <linux/delay.h>
 #include <linux/ioport.h>
 #include <linux/platform_device.h>
+#include <linux/usb/isp116x.h>
 #include <linux/vt_kern.h>
 #include <linux/module.h>
 
@@ -685,8 +686,70 @@ static struct platform_device smc91x_device = {
        .resource       = smc91x_resources,
 };
 
+/*
+ * ISP 1160 - using the isp116x-hcd module
+ */
+
+#define ATARI_USB_PHYS_ADDR    0x80000012
+#define ATARI_USB_IRQ          139
+
+static struct resource isp1160_resources[] = {
+       [0] = {
+               .name   = "isp1160-data",
+               .start  = ATARI_USB_PHYS_ADDR,
+               .end    = ATARI_USB_PHYS_ADDR + 0x1,
+               .flags  = IORESOURCE_MEM,
+       },
+       [1] = {
+               .name   = "isp1160-regs",
+               .start  = ATARI_USB_PHYS_ADDR + 0x4,
+               .end    = ATARI_USB_PHYS_ADDR + 0x5,
+               .flags  = IORESOURCE_MEM,
+       },
+       [2] = {
+               .name   = "isp1160-irq",
+               .start  = ATARI_USB_IRQ,
+               .end    = ATARI_USB_IRQ,
+               .flags  = IORESOURCE_IRQ,
+       },
+};
+
+static void isp1160_delay(struct device *dev, int delay)
+{
+       ndelay(delay);
+}
+
+/* (DataBusWidth16|AnalogOCEnable|DREQOutputPolarity|DownstreamPort15KRSel ) */
+static struct isp116x_platform_data isp1160_platform_data = {
+       /* Enable internal resistors on downstream ports */
+       .sel15Kres              = 1,
+       /* On-chip overcurrent protection */
+       .oc_enable              = 1,
+       /* INT output polarity */
+       .int_act_high           = 1,
+       /* INT edge or level triggered */
+       .int_edge_triggered     = 0,
+
+       /* WAKEUP pin connected - NOT SUPPORTED  */
+       /* .remote_wakeup_connected = 0, */
+       /* Wakeup by devices on usb bus enabled */
+       .remote_wakeup_enable   = 0,
+       .delay                  = isp1160_delay,
+};
+
+static struct platform_device isp1160_device = {
+       .name           = "isp116x-hcd",
+       .id             = 0,
+       .num_resources  = ARRAY_SIZE(isp1160_resources),
+       .resource       = isp1160_resources,
+       .dev                    = {
+               .platform_data  = &isp1160_platform_data,
+       },
+};
+
 static struct platform_device *atari_ethernat_devices[] __initdata = {
-       &smc91x_device
+       &smc91x_device,
+       &isp1160_device
 };
 
 #define ATARI_ETHERNEC_PHYS_ADDR       0xfffa0000
@@ -715,8 +778,66 @@ static struct platform_device rtl8019_device = {
        .resource       = rtl8019_resources,
 };
 
-static struct platform_device *atari_ethernec_devices[] __initdata = {
-       &rtl8019_device
+/*
+ * NetUSBee: ISP1160 USB host adapter via ROM-port adapter
+ */
+
+#define ATARI_NETUSBEE_PHYS_ADDR       0xfffa8000
+#define ATARI_NETUSBEE_BASE            0x340
+#define ATARI_NETUSBEE_IRQ             IRQ_MFP_TIMER2
+
+static struct resource netusbee_resources[] = {
+       [0] = {
+               .name   = "isp1160-data",
+               .start  = ATARI_NETUSBEE_BASE,
+               .end    = ATARI_NETUSBEE_BASE + 0x1,
+               .flags  = IORESOURCE_MEM,
+       },
+       [1] = {
+               .name   = "isp1160-regs",
+               .start  = ATARI_NETUSBEE_BASE + 0x20,
+               .end    = ATARI_NETUSBEE_BASE + 0x21,
+               .flags  = IORESOURCE_MEM,
+       },
+       [2] = {
+               .name   = "isp1160-irq",
+               .start  = ATARI_NETUSBEE_IRQ,
+               .end    = ATARI_NETUSBEE_IRQ,
+               .flags  = IORESOURCE_IRQ,
+       },
+};
+
+/* (DataBusWidth16|AnalogOCEnable|DREQOutputPolarity|DownstreamPort15KRSel ) */
+static struct isp116x_platform_data netusbee_platform_data = {
+       /* Enable internal resistors on downstream ports */
+       .sel15Kres              = 1,
+       /* On-chip overcurrent protection */
+       .oc_enable              = 1,
+       /* INT output polarity */
+       .int_act_high           = 1,
+       /* INT edge or level triggered */
+       .int_edge_triggered     = 0,
+
+       /* WAKEUP pin connected - NOT SUPPORTED  */
+       /* .remote_wakeup_connected = 0, */
+       /* Wakeup by devices on usb bus enabled */
+       .remote_wakeup_enable   = 0,
+       .delay                  = isp1160_delay,
+};
+
+static struct platform_device netusbee_device = {
+       .name           = "isp116x-hcd",
+       .id             = 1,
+       .num_resources  = ARRAY_SIZE(netusbee_resources),
+       .resource       = netusbee_resources,
+       .dev                    = {
+               .platform_data  = &netusbee_platform_data,
+       },
+};
+
+static struct platform_device *atari_netusbee_devices[] __initdata = {
+       &rtl8019_device,
+       &netusbee_device
 };
 
 int __init atari_platform_init(void)
@@ -744,8 +865,8 @@ int __init atari_platform_init(void)
                unsigned char *enec_virt;
                enec_virt = (unsigned char 
*)ioremap((ATARI_ETHERNEC_PHYS_ADDR), 0xf);
                if (hwreg_present(enec_virt)) {
-                       error = platform_add_devices(atari_ethernec_devices,
-                                               
ARRAY_SIZE(atari_ethernec_devices));
+                       error = platform_add_devices(atari_netusbee_devices,
+                                               
ARRAY_SIZE(atari_netusbee_devices));
                        if (error && !rv)
                                rv = error;
                }
-- 
1.7.0.4


-- 
To UNSUBSCRIBE, email to [email protected]
with a subject of "unsubscribe". Trouble? Contact [email protected]
Archive: 
http://lists.debian.org/[email protected]

Reply via email to