Package: Installation-reports
Boot method: DVD
Image version: debian-4.0r3-i386-DVD-1.iso
Date: Mon Jul 7, 2008 7:05 pm
Machine: hp server tc2120 (470061-156)
Processor: Intel Pentium 4 2.80 GHz Integrated 512-KB Level 2 cache Memory:
4x256(512) MB PC2100 DDR SDRAM DIMM running at 266MHz, with Advanced ECC
capabilities
Other Hardware Details:
NC7760 PCI Gigabit NIC 10/100/1000 (Broadcom NetXtreme BCM5702)
Adaptec 2110S Raid controller
HP Single Channel SCSI Adapter
3x36.4 GB SCSI Disks (Raid-5 volume created)
Hp Surestore DAT 40
HP DVD Writer 630
ATI RAGE XL Video with 8MB SDRAM Video Memory
ACPI V1.0b Compliant
PCI 2.2 Compliant
PXE Support
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot: [O]
Detect network card: [O]
Configure network: [O]
Detect CD: [O]
Load installer modules: [O]
Detect hard drives: [O]
Partition hard drives: [O]
Install base system: [O]
Clock/timezone setup: [O]
User/password setup: [O]
Install tasks: [O]
Install boot loader: [O]
Overall install: [O]
Comments/Problems:
Installation process is completed successfully. Then, during post-installation
boot process the following messages appear at screen:
iop0: PCI I2O controller at FC000000 size=1048576
iop0: installed at IRQ 193
i2o: iop0: Activating I2O controller….
i2o: iop0: This may take a few minutes if there are many device
iop0: HRT has 1 entries of 16 bytes each
Adapter 00000012: TID 0000[HPC*]: PCI 1: Bus 1 Device 22 Function 0
i2o: op0: Controller added
Loading Adaptec I2O RAID: Version 2.4 Build 5ago
Detecting Adaptec I2O RAID controllers…..
PCI: Unable to reserve mem region #1:[EMAIL PROTECTED] for device 0000:00:06.0
dpti: adpt_config_hba: pci request region failed
Could not init an I2O RAID device
Will not try to detect others
I2O Block Device OSM v1.325
block-osm registered device at mayor 80
hdc: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver revision: 3.20
i2o/had i2o/hda1 i2o/hda2
block-osm device added (TID: 207) i2o/had
Done.
Begin: Mounting root file system… …
Begin: Running /scripts/local-top
Done.
Begin: Waiting for root file system… …
Boot process stops here. Then, the system takes some minutes and an initramfs
prompt appears at screen.
Using Debian Sarge 3.1r5 or 3.1r8 versions (kernel 2.6.8.4-i386), the
installation process is completed without any error and the post-installation
boot process is completed successfully.
Output of lspci –nn using Sarge version.
0000:00:00.0 0600: 1166:0017 (rev 32)
0000:00:00.1 0600: 1166:0017
0000:00:03.0 0200: 14e4:16a6 (rev 02)
0000:00:04.0 0100: 9005:0080 (rev 02)
0000:00:06.0 0e00: 1044:a501 (rev 01)
0000:00:06.1 0604: 1044:a500 (rev 01)
0000:00:07.0 0200: 10b7:9200 (rev 78)
0000:00:09.0 0300: 1002:4752 (rev 27)
0000:00:0f.0 0601: 1166:0203 (rev a0)
0000:00:0f.1 0101: 1166:0213 (rev a0)
0000:00:0f.2 0c03: 1166:0221 (rev 05)
0000:00:0f.3 0600: 1166:0227
Output of lspci –vnn using Sarge version.
0000:00:00.0 0600: 1166:0017 (rev 32)
Flags: fast devsel
0000:00:00.1 0600: 1166:0017
Flags: fast devsel
0000:00:03.0 0200: 14e4:16a6 (rev 02)
Subsystem: 0e11:00bb
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 169
Memory at fb000000 (64-bit, non-prefetchable) [size=64K]
Expansion ROM at febf0000 [disabled] [size=64K]
Capabilities: [40] PCI-X non-bridge device.
Capabilities: [48] Power Management version 2
Capabilities: [50] Vital Product Data
Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/3
Enable-
0000:00:04.0 0100: 9005:0080 (rev 02)
Subsystem: 0e11:e2a0
Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 177
BIST result: 00
I/O ports at d800 [disabled] [size=256]
Memory at fa800000 (64-bit, non-prefetchable) [size=4K]
Expansion ROM at febc0000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
0000:00:06.0 0e00: 1044:a501 (rev 01) (prog-if 01)
Subsystem: 1044:c066
Flags: bus master, 66MHz, slow devsel, latency 32, IRQ 185
BIST result: 00
Memory at fc000000 (32-bit, prefetchable) [size=32M]
Capabilities: [80] Power Management version 2
0000:00:06.1 0604: 1044:a500 (rev 01)
Flags: bus master, 66MHz, slow devsel, latency 32
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
Capabilities: [68] Power Management version 2
0000:00:07.0 0200: 10b7:9200 (rev 78)
Subsystem: 10b7:1000
Flags: bus master, medium devsel, latency 32, IRQ 193
I/O ports at b800 [size=128]
Memory at fa000000 (32-bit, non-prefetchable) [size=128]
Capabilities: [dc] Power Management version 2
0000:00:09.0 0300: 1002:4752 (rev 27)
Subsystem: 0e11:001e
Flags: bus master, stepping, medium devsel, latency 32, IRQ 201
Memory at f9000000 (32-bit, non-prefetchable) [size=16M]
I/O ports at b400 [size=256]
Memory at f8800000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at fbec0000 [disabled] [size=128K]
Capabilities: [5c] Power Management version 2
0000:00:0f.0 0601: 1166:0203 (rev a0)
Subsystem: 1166:0201
Flags: bus master, medium devsel, latency 32
0000:00:0f.1 0101: 1166:0213 (rev a0) (prog-if 8a [Master SecP PriP])
Subsystem: 1166:0212
Flags: bus master, medium devsel, latency 64
I/O ports at <ignored>
I/O ports at <ignored>
I/O ports at <ignored>
I/O ports at <ignored>
I/O ports at 9800 [size=16]
0000:00:0f.2 0c03: 1166:0221 (rev 05) (prog-if 10)
Subsystem: 1166:0220
Flags: bus master, medium devsel, latency 32, IRQ 10
Memory at f8000000 (32-bit, non-prefetchable) [size=4K]
0000:00:0f.3 0600: 1166:0227
Subsystem: 1166:0230
Flags: bus master, medium devsel, latency 0
Boot messages referring to dpt_i2o are quiet different, but I can’t see them
completely.
Angel
________________________________
Enviado desde Correo Yahoo!
La bandeja de entrada más inteligente.
______________________________________________
Enviado desde Correo Yahoo! La bandeja de entrada más inteligente.
