Package: installation-reports Version: N/A; reported 2003-12-19 Severity: normal
INSTALL REPORT Debian-installer-version: Downloaded on 2003-12-18 http://people.debian.org/~manty/testing/netinst/i386/daily/sarge-i386-netinst.iso Date on web page says 17-Dec-2003 07:34. uname -a: Linux shaavik3 2.6.0 #1 Thu Dec 18 08:21:27 EST 2003 i686 GNU/Linux Date: 2003-12-19 Machine: Gateway E-6100 Processor: Intel(R) Pentium(R) 4 CPU 3.00GHz Memory: 512 meg Output of lspci: 00:00.0 Host bridge: Intel Corp. 82875P Memory Controller Hub (rev 02) 00:01.0 PCI bridge: Intel Corp. 82875P Processor to AGP Controller (rev 02) 00:03.0 PCI bridge: Intel Corp. 82875P Processor to PCI to CSA Bridge (rev 02) 00:1d.0 USB Controller: Intel Corp. 82801EB USB (rev 02) 00:1d.1 USB Controller: Intel Corp. 82801EB USB (rev 02) 00:1d.2 USB Controller: Intel Corp. 82801EB USB (rev 02) 00:1d.3 USB Controller: Intel Corp. 82801EB USB (rev 02) 00:1d.7 USB Controller: Intel Corp. 82801EB USB2 (rev 02) 00:1e.0 PCI bridge: Intel Corp. 82801BA/CA/DB/EB PCI Bridge (rev c2) 00:1f.0 ISA bridge: Intel Corp. 82801EB LPC Interface Controller (rev 02) 00:1f.1 IDE interface: Intel Corp. 82801EB Ultra ATA Storage Controller (rev 02) 00:1f.2 IDE interface: Intel Corp. 82801EB Ultra ATA Storage Controller (rev 02) 00:1f.3 SMBus: Intel Corp. 82801EB SMBus Controller (rev 02) 01:00.0 VGA compatible controller: nVidia Corporation NV34 [GeForce FX 5200] (rev a1) 02:01.0 Ethernet controller: Intel Corp.: Unknown device 1019 03:03.0 Multimedia audio controller: Ensoniq 5880 AudioPCI (rev 04) Base System Installation Checklist: Initial boot worked: [O] Configure network HW: [E] Config network: [ ] Detect CD: [ ] Load installer modules: [ ] Detect hard drives: [ ] Partition hard drives: [ ] Create file systems: [ ] Mount partitions: [ ] Install base system: [ ] Install boot loader: [ ] Reboot: [ ] [O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it Comments/Problems: The system lockup hard when it loads the ide-detect module. I am able to boot it using Knoppix and I was able to install stable on it using a disk from http://nihonlinux.jp/release_en.html. If I remember right, it uses the piix driver (for the ICH5 support.) Here is a chunk of the dmesg output from 2.6.0: Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ICH5: IDE controller at PCI slot 0000:00:1f.1 PCI: Enabling device 0000:00:1f.1 (0005 -> 0007) ICH5: chipset revision 2 ICH5: not 100% native mode: will probe irqs later ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:pio, hdb:pio ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio hdc: HL-DT-ST DVDRAM GSA-4040B, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 hdc: ATAPI 32X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.12 libata version 0.81 loaded. ata_piix version 0.95 PCI: Setting latency timer of device 0000:00:1f.2 to 64 ata1: SATA max UDMA/133 cmd 0xEC00 ctl 0xE802 bmdma 0xDC00 irq 18 ata2: SATA max UDMA/133 cmd 0xE400 ctl 0xE002 bmdma 0xDC08 irq 18 ata1: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4003 85:7c69 86:3f01 87:4003 88:207f ata1: dev 0 ATA, max UDMA/133, 320173056 sectors (lba48) ata1: dev 0 configured for UDMA/133 scsi0 : ata_piix ata2: SATA port has no device. disabling. ata2: thread exiting scsi1 : ata_piix Vendor: ATA Model: Maxtor 6Y160M0 Rev: 0.81 Type: Direct-Access ANSI SCSI revision: 05 SCSI device sda: 320173056 512-byte hdwr sectors (163929 MB) SCSI device sda: drive cache: write through sda: sda1 sda2 sda3 sda4 Attached scsi disk sda at scsi0, channel 0, id 0, lun 0 Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0 -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
