Package: installation-reports Debian-installer-version: 2004-03-14 http://http.us.debian.org/debian/dists/testing/main/installer-i386/current/images/floppy/boot.img
uname -a: Linux milo 2.6.3-1-686-smp #2 SMP Tue Feb 24 20:29:08 EST 20 Date: 2004-03-18 20:15 Method: Boot from floppy Network install from ftp.us.debian.org Machine: IBM xSeries 235 Processor: Dual PIII 2.4 Xeon Processors Memory: 2048 MB Root Device: scsi0 : IBM PCI ServeRAID 7.00.00 Build 475 <ServeRAID 5i> /dev/sda Root Size/partition table: /dev/sda1 8642 8885 1952244 82 Linux swap /dev/sda2 * 1 61 488029+ 83 Linux /dev/sda3 62 488 3416427 83 Linux /dev/sda4 489 8641 65232153 83 Linux /dev/sda4 65230132 293372 64936760 1% / /dev/sda2 457341 17232 415708 4% /boot /dev/sda3 3416272 36492 3379780 2% /var/log tmpfs 1036616 0 1036616 0% /dev/shm Output of lspci: 00:00.0 Host bridge: ServerWorks CMIC-LE (rev 13) 00:00.1 Host bridge: ServerWorks CMIC-LE 00:00.2 Host bridge: ServerWorks: Unknown device 0000 00:09.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev 27) 00:0f.0 Host bridge: ServerWorks CSB5 South Bridge (rev 93) 00:0f.1 IDE interface: ServerWorks CSB5 IDE Controller (rev 93) 00:0f.2 USB Controller: ServerWorks OSB4/CSB5 OHCI USB Controller (rev 05) 00:0f.3 ISA bridge: ServerWorks GCLE Host Bridge 00:10.0 Host bridge: ServerWorks: Unknown device 0101 (rev 03) 00:10.2 Host bridge: ServerWorks: Unknown device 0101 (rev 03) 00:11.0 Host bridge: ServerWorks: Unknown device 0101 (rev 03) 00:11.2 Host bridge: ServerWorks: Unknown device 0101 (rev 03) 02:08.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5703 Gigabit Ethernet (rev 02) 05:03.0 RAID bus controller: IBM ServeRAID Controller Base System Installation Checklist: Initial boot worked: [O] Configure network HW: [O] Config network: [O] Detect CD: [ ] Load installer modules: [O] Detect hard drives: [O] Partition hard drives: [O] Create file systems: [O] Mount partitions: [O] Install base system: [O] Install boot loader: [O] Reboot: [O] [O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it Comments/Problems: I did the install off of just boot.img and root.img - there were no problems with the scsi or the NIC (eth0: Tigon3 [partno(BCM95703A30) rev 1002 PHY(5703)] (PCIX:100MHz:64-bit) 10/100/1000BaseT Ethernet 00:02:55:07:17:41). I've done the install twice (just for fun) and tried to accept all the defaults (except for loading additional drivers, and setting up the partition table), just to see what happened. The original boot to: vmlinuz-2.4.25-1-386 Was fine. I also grabbed: vmlinuz-2.6.3-1-686-smp and had no problems booting. Now I'm running off of: vmlinuz-2.4.25-1-686-smp Thanks! -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
