Package: installation-reports INSTALL REPORT
Debian-installer-version: debian-31r2-i386-netinst.iso downloaded on 04. Sept 2006 via http://www.debian.org/CD/netinst/ (oh shit! I see today there is debian-31r3-i386-netinst.iso available) uname -a: Linux Hiltja 2.4.27-2-386 #1 Wed Aug 17 09:33:35 UTC 2005 i686 GNU/Linux Date: Mo 04. Sept 2006 11:00 Method: Boot from CD Machine: ASUS A3FP Processor: Intel Core Duo T2400 1,83GHz Memory: 1024 MB, DDR2 667 Root Device: IDE, Ultra ATA, 100 GB ------------------------------------------------ Root Size/partition table: Disk /dev/hda: 12161 cylinders, 255 heads, 63 sectors/track Units = cylinders of 8225280 bytes, blocks of 1024 bytes, counting from 0 Device Boot Start End #cyls #blocks Id System /dev/hda1 * 0+ 11822 11823- 94968216 83 Linux /dev/hda2 11823 12160 338 2714985 5 Extended /dev/hda3 0 - 0 0 0 Empty /dev/hda4 0 - 0 0 0 Empty /dev/hda5 11823+ 12160 338- 2714953+ 82 Linux swap / Solaris ------------------------------------------------ Output of lspci and lspci -n: -- lspci -- 0000:00:00.0 Host bridge: Intel Corp.: Unknown device 27a0 (rev 03) 0000:00:02.0 VGA compatible controller: Intel Corp.: Unknown device 27a2 (rev 03) 0000:00:02.1 Display controller: Intel Corp.: Unknown device 27a6 (rev 03) 0000:00:1b.0 0403: Intel Corp.: Unknown device 27d8 (rev 02) 0000:00:1c.0 PCI bridge: Intel Corp.: Unknown device 27d0 (rev 02) 0000:00:1c.1 PCI bridge: Intel Corp.: Unknown device 27d2 (rev 02) 0000:00:1d.0 USB Controller: Intel Corp.: Unknown device 27c8 (rev 02) 0000:00:1d.1 USB Controller: Intel Corp.: Unknown device 27c9 (rev 02) 0000:00:1d.2 USB Controller: Intel Corp.: Unknown device 27ca (rev 02) 0000:00:1d.3 USB Controller: Intel Corp.: Unknown device 27cb (rev 02) 0000:00:1d.7 USB Controller: Intel Corp.: Unknown device 27cc (rev 02) 0000:00:1e.0 PCI bridge: Intel Corp. 82801 PCI Bridge (rev e2) 0000:00:1f.0 ISA bridge: Intel Corp.: Unknown device 27b9 (rev 02) 0000:00:1f.1 IDE interface: Intel Corp.: Unknown device 27df (rev 02) 0000:02:00.0 Network controller: Intel Corp.: Unknown device 4222 (rev 02) 0000:03:01.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev b3) 0000:03:01.1 FireWire (IEEE 1394): Ricoh Co Ltd R5C552 IEEE 1394 Controller (rev 08) 0000:03:01.2 0805: Ricoh Co Ltd: Unknown device 0822 (rev 17) 0000:03:01.3 System peripheral: Ricoh Co Ltd: Unknown device 0592 (rev 08) 0000:03:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) -- lspci -n ---- 0000:00:00.0 0600: 8086:27a0 (rev 03) 0000:00:02.0 0300: 8086:27a2 (rev 03) 0000:00:02.1 0380: 8086:27a6 (rev 03) 0000:00:1b.0 0403: 8086:27d8 (rev 02) 0000:00:1c.0 0604: 8086:27d0 (rev 02) 0000:00:1c.1 0604: 8086:27d2 (rev 02) 0000:00:1d.0 0c03: 8086:27c8 (rev 02) 0000:00:1d.1 0c03: 8086:27c9 (rev 02) 0000:00:1d.2 0c03: 8086:27ca (rev 02) 0000:00:1d.3 0c03: 8086:27cb (rev 02) 0000:00:1d.7 0c03: 8086:27cc (rev 02) 0000:00:1e.0 0604: 8086:2448 (rev e2) 0000:00:1f.0 0601: 8086:27b9 (rev 02) 0000:00:1f.1 0101: 8086:27df (rev 02) 0000:02:00.0 0280: 8086:4222 (rev 02) 0000:03:01.0 0607: 1180:0476 (rev b3) 0000:03:01.1 0c00: 1180:0552 (rev 08) 0000:03:01.2 0805: 1180:0822 (rev 17) 0000:03:01.3 0880: 1180:0592 (rev 08) 0000:03:07.0 0200: 10ec:8139 (rev 10) ------------------------------------------------ Base System Installation Checklist: [O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it Initial boot worked: [O] Configure network HW: [O] Config network: [O] Detect CD: [O] Load installer modules: [O] Detect hard drives: [O] Partition hard drives: [O] Create file systems: [O] Mount partitions: [O] Install base system: [O] Install boot loader: [O] Reboot: [O] Comments/Problems: * base-install worked fine * base-config worked, but was unable to identify the graphics chip [intel 945GM] so I have to use vesa driver to get X running - thanx for the quick help from bugs.debian.org * didnt yet check all the builtin peripherals / devices of the notebook * why isnt fetchmail included in the default desktop-environment packages? * would be nice to have a "back to previous screen" function in base-config - I selected wrong item, intuitively tried to <ESCAPE> back - that of course didnt work but caused base-config to continue with next step and as beginner it was hard for me to find out the right config-tool afterwards. * in all HowTos RUNLEVEL 2 is said to be an environment without X. But in this installation it seems to be identical with RUNLEVEL 3 Dont like that cause I like the black&white 80x25 Linux - still exploring how to switch without reboot... * the greatest moment during installation was when I pressed ENTER to start partitioning: Kill WinXP - I want LINUX!! -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]