Your message dated Sun, 9 Dec 2007 15:57:44 +0100
with message-id <[EMAIL PROTECTED]>
and subject line Bug#454618: [sparc] netra x1 - flapping interfaces / not
installable
has caused the attached Bug report to be marked as done.
This means that you claim that the problem has been dealt with.
If this is not the case it is now your responsibility to reopen the
Bug report if necessary, and/or fix the problem forthwith.
(NB: If you are a system administrator and have no idea what I am
talking about this indicates a serious mail system misconfiguration
somewhere. Please contact me immediately.)
Debian bug tracking system administrator
(administrator, Debian Bugs database)
--- Begin Message ---
Package: debian-installer
Version: snapshot-20071127
Hi,
i just tried installing Debian/Etch on an Sun Netra X1 and it failed. I
retried with a current snapshot from here:
http://people.debian.org/~stappers/d-i/images/20071127-12:10/netboot/boot.img
and it fails the same way. When gettint to the network configuration
both ethernets immediatly start flapping and DHCP does not succeed.
Dec 6 17:24:17.459 MEZ: %LINK-3-UPDOWN: Interface FastEthernet0/3,
changed state to down
Dec 6 17:24:21.060 MEZ: %LINK-3-UPDOWN: Interface FastEthernet0/3,
changed state to up
Dec 6 17:24:23.460 MEZ: %LINK-3-UPDOWN: Interface FastEthernet0/3,
changed state to down
Dec 6 17:24:27.060 MEZ: %LINK-3-UPDOWN: Interface FastEthernet0/3,
changed state to up
Dec 6 17:24:29.460 MEZ: %LINK-3-UPDOWN: Interface FastEthernet0/3,
changed state to down
Dec 6 17:24:33.060 MEZ: %LINK-3-UPDOWN: Interface FastEthernet0/3,
changed state to up
Dec 6 17:24:35.460 MEZ: %LINK-3-UPDOWN: Interface FastEthernet0/3,
changed state to down
Dec 6 17:24:41.260 MEZ: %LINK-3-UPDOWN: Interface FastEthernet0/3,
changed state to up
This seems to be caused by the driver unable to assign a MAC Address:
eth0 Link encap:Ethernet HWaddr 00:00:00:00:00:00
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:9
eth1 Link encap:Ethernet HWaddr 00:00:00:00:00:00
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:10 Base address:0x100
This is the very same problem as #360699 reported which was closed.
Unloading dmfe.ko and loading tulip.ko (and removing dmfe.ko to
dismiss further loading) helps ...
00:05.0 Ethernet controller: Davicom Semiconductor, Inc. 21x4x DEC-Tulip
compatible 10/100 Ethernet (rev 31)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort+ <MAbort- >SERR+ <PERR+
Latency: 0 (5000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at 1fe02010100 [size=256]
Region 1: Memory at 1ff00002000 (32-bit, non-prefetchable) [size=8K]
Expansion ROM at 1ff00080000 [disabled] [size=256K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=220mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0c.0 Ethernet controller: Davicom Semiconductor, Inc. 21x4x DEC-Tulip
compatible 10/100 Ethernet (rev 31)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort+ <MAbort- >SERR+ <PERR+
Latency: 0 (5000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 9
Region 0: I/O ports at 1fe02010000 [size=256]
Region 1: [virtual] Memory at 1ff00000000 (32-bit, non-prefetchable)
[size=8K]
Expansion ROM at 1ff00040000 [disabled] [size=256K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=220mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
At least the kernel does not Oops when unloading the dmfe driver as the
Etch installer kernel did for me...
Flo
--
Florian Lohoff [EMAIL PROTECTED] +49-171-2280134
Those who would give up a little freedom to get a little
security shall soon have neither - Benjamin Franklin
signature.asc
Description: Digital signature
--- End Message ---
--- Begin Message ---
On Thursday 06 December 2007, Florian Lohoff wrote:
> Unloading dmfe.ko and loading tulip.ko (and removing dmfe.ko to
> dismiss further loading) helps ...
Closing this report as the installer already offers a workaround for this
and the basic problem is an upstream kernel issue which is outside the
scope of the D-I team.
As mentioned in an earlier reply, by far the most effective way to get this
resolved structurally would be to contact the kernel developers directly.
Cheers,
FJP
--- End Message ---
