Your message dated Sat, 18 Jul 2009 00:41:43 +0200
with message-id <[email protected]>
and subject line Re: Bug#427072: Acknowledgement (BUG: unable to handle kernel
NULL pointer dereference at virtual address 0000001c)
has caused the Debian Bug report #427072,
regarding BUG: unable to handle kernel NULL pointer dereference at virtual
address 0000001c
to be marked as done.
This means that you claim that the problem has been dealt with.
If this is not the case it is now your responsibility to reopen the
Bug report if necessary, and/or fix the problem forthwith.
(NB: If you are a system administrator and have no idea what this
message is talking about, this may indicate a serious mail system
misconfiguration somewhere. Please contact [email protected]
immediately.)
--
427072: http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=427072
Debian Bug Tracking System
Contact [email protected] with problems
--- Begin Message ---
Package: linux-image-2.6.21-1-686
Version: 2.6.21-4
Severity: normal
When I do "statserial /dev/ttyUSB2" this happens (I think the included
Kernel log provides enough data).
/dev/ttyUSB2 is on a Huawei E618 PCMCIA UMTS/GPRS card.
Here is what ATI says about the card:
Manufacturer: HUAWEI TECHNOLOGIES CO., LTD.
Model: 183
Revision: I:12.11.01B
I ommited the IMEI.
-- Package-specific info:
** Version: Linux version 2.6.21-1-686 (Debian 2.6.21-4) ([email protected])
(gcc version 4.1.3 20070518 (prerelease) (Debian 4.1.2-8)) #1 SMP Sat May 26
16:14:59 UTC 2007
** Not tainted
** Kernel log:
pccard: CardBus card inserted into slot 0
pccard: CardBus card inserted into slot 1
[1487] nozomi_card_init(): Init, cards_found: 1
[1373] nozomi_get_card_type(): Card type is: 2048
PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNKC] -> GSI 11 (level, low) ->
IRQ 11
Nozomi driver nozomi_tty<6>[836] nozomi_read_config_table(): Version of card: 3
Initializing Nozomi driver 2.1 (build date: Jun 1 2007 19:26:41)
[828] nozomi_read_config_table(): Initialization OK!
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
PCI: Enabling device 0000:06:00.0 (0000 -> 0002)
ACPI: PCI Interrupt 0000:06:00.0[A] -> Link [LNKC] -> GSI 11 (level, low) ->
IRQ 11
PCI: Setting latency timer of device 0000:06:00.0 to 64
ohci_hcd 0000:06:00.0: OHCI Host Controller
ohci_hcd 0000:06:00.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:06:00.0: irq 11, io mem 0x1c000000
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
PCI: Enabling device 0000:06:00.1 (0000 -> 0002)
ACPI: PCI Interrupt 0000:06:00.1[B] -> Link [LNKC] -> GSI 11 (level, low) ->
IRQ 11
PCI: Setting latency timer of device 0000:06:00.1 to 64
ohci_hcd 0000:06:00.1: OHCI Host Controller
ohci_hcd 0000:06:00.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:06:00.1: irq 11, io mem 0x1c001000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 1 port detected
usb 2-1: new full speed USB device using ohci_hcd and address 2
usb 2-1: configuration #1 chosen from 1 choice
usbcore: registered new interface driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core
drivers/usb/serial/usb-serial.c: USB Serial support registered for pl2303
pl2303 2-1:1.0: pl2303 converter detected
usb 2-1: pl2303 converter now attached to ttyUSB0
pl2303 2-1:1.1: pl2303 converter detected
usb 2-1: pl2303 converter now attached to ttyUSB1
pl2303 2-1:1.2: pl2303 converter detected
usb 2-1: pl2303 converter now attached to ttyUSB2
usbcore: registered new interface driver pl2303
drivers/usb/serial/pl2303.c: Prolific PL2303 USB to serial adaptor driver
drivers/usb/serial/usb-serial.c: USB Serial support registered for GSM modem
(1-port)
usbcore: registered new interface driver option
drivers/usb/serial/option.c: USB Driver for GSM modems: v0.7.1
EXT3 FS on hda1, internal journal
loop: loaded (max 8 devices)
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: [email protected]
eth0: link up, 10Mbps, half-duplex, lpa 0x0000
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
eth0: no IPv6 routers present
BUG: unable to handle kernel NULL pointer dereference at virtual address
0000001c
printing eip:
c8991984
*pde = 00000000
Oops: 0002 [#1]
SMP
Modules linked in: ext2 ipv6 dm_crypt dm_snapshot dm_mirror dm_mod loop option
pl2303 usbserial ohci_hcd nozomi pcmcia firmware_class psmouse serio_raw rtc
i2c_piix4 yenta_socket rsrc_nonstatic pcspkr pcmcia_core i2c_core shpchp
pci_hotplug intel_agp agpgart sd_mod evdev ext3 jbd mbcache usb_storage
ide_disk 8139too generic 8139cp mii uhci_hcd usbcore piix ide_core ata_generic
libata scsi_mod thermal processor fan
CPU: 0
EIP: 0060:[<c8991984>] Not tainted VLI
EFLAGS: 00210246 (2.6.21-1-686 #1)
EIP is at pl2303_open+0x896/0x8f5 [pl2303]
eax: 00000000 ebx: 00000000 ecx: 00200246 edx: c7257000
esi: c13fc960 edi: c1395600 ebp: c773bda0 esp: c503be38
ds: 007b es: 007b fs: 00d8 gs: 0033 ss: 0068
Process statserial (pid: 2233, ti=c503a000 task=c7a0d070 task.ti=c503a000)
Stack: 00000040 00000009 00000000 00000000 00000000 00000064 00000003 00200286
00000000 c50cd000 c13e8800 00200286 c020f7a1 00000000 c0210406 c0165c68
00000901 00000000 c503bec8 c1395600 c13fc960 c50cd000 ffffffed c89c1f6d
Call Trace:
[<c020f7a1>] tty_ldisc_enable+0x27/0x29
[<c0210406>] init_dev+0x399/0x4a9
[<c0165c68>] get_unused_fd+0x4a/0xaa
[<c89c1f6d>] serial_open+0xcb/0x11c [usbserial]
[<c0212add>] tty_open+0x16c/0x2c3
[<c01697b8>] chrdev_open+0x120/0x13b
[<c0169698>] chrdev_open+0x0/0x13b
[<c0165d8b>] __dentry_open+0xc3/0x17a
[<c0165ebc>] nameidata_to_filp+0x24/0x33
[<c0165efd>] do_filp_open+0x32/0x39
[<c0165c68>] get_unused_fd+0x4a/0xaa
[<c0165f46>] do_sys_open+0x42/0xc3
[<c0166000>] sys_open+0x1c/0x1e
[<c0103d8c>] syscall_call+0x7/0xb
[<c0290000>] __find_acq_core+0x2ce/0x30e
=======================
Code: 6e 83 3d c0 4b 99 c8 00 74 1c c7 44 24 08 54 23 99 c8 c7 44 24 04 70 23
99 c8 c7 04 24 97 28 99 c8 e8 16 0c 79 f7 8b 47 24 8b 16 <89> 50 1c 8b 47 24 ba
d0 00 00 00 e8 20 72 ea ff 89 c3 31 c0 85
EIP: [<c8991984>] pl2303_open+0x896/0x8f5 [pl2303] SS:ESP 0068:c503be38
** Loaded modules:
Module Size Used by
ext2 60168 1
ipv6 236320 12
dm_crypt 12808 0
dm_snapshot 16420 0
dm_mirror 20116 0
dm_mod 52556 3 dm_crypt,dm_snapshot,dm_mirror
loop 15880 0
option 9440 0
pl2303 19396 1
usbserial 31528 4 option,pl2303
ohci_hcd 19684 0
nozomi 18608 0
pcmcia 35276 0
firmware_class 9408 1 pcmcia
psmouse 34952 0
serio_raw 6564 0
rtc 12760 0
i2c_piix4 8556 0
yenta_socket 24876 4
rsrc_nonstatic 11968 1 yenta_socket
pcspkr 3136 0
pcmcia_core 36884 3 pcmcia,yenta_socket,rsrc_nonstatic
i2c_core 20480 1 i2c_piix4
shpchp 30996 0
pci_hotplug 29088 1 shpchp
intel_agp 23004 1
agpgart 32168 1 intel_agp
sd_mod 19904 2
evdev 9216 0
ext3 120904 1
jbd 55208 1 ext3
mbcache 8164 2 ext2,ext3
usb_storage 76384 1
ide_disk 15648 2
8139too 25536 0
generic 4804 0 [permanent]
8139cp 22336 0
mii 5280 2 8139too,8139cp
uhci_hcd 22608 0
usbcore 123304 7
option,pl2303,usbserial,ohci_hcd,usb_storage,uhci_hcd
piix 9508 0 [permanent]
ide_core 115016 4 usb_storage,ide_disk,generic,piix
ata_generic 8100 0
libata 109172 1 ata_generic
scsi_mod 133740 3 sd_mod,usb_storage,libata
thermal 14120 0
processor 30888 1 thermal
fan 4868 0
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX Host
bridge [8086:7190] (rev 03)
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:8024]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 64
Region 0: Memory at e4000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 1.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans-
64bit- FW- AGP3- Rate=x1,x2
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW-
Rate=<none>
00:01.0 PCI bridge [0604]: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX AGP
bridge [8086:7191] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B+
00:04.0 ISA bridge [0601]: Intel Corporation 82371AB/EB/MB PIIX4 ISA
[8086:7110] (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:04.1 IDE interface [0101]: Intel Corporation 82371AB/EB/MB PIIX4 IDE
[8086:7111] (rev 01) (prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable)
[disabled] [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable)
[disabled] [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable)
[disabled] [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable)
[disabled] [size=1]
Region 4: I/O ports at d800 [size=16]
00:04.2 USB Controller [0c03]: Intel Corporation 82371AB/EB/MB PIIX4 USB
[8086:7112] (rev 01) (prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin D routed to IRQ 7
Region 4: I/O ports at d400 [size=32]
00:04.3 Bridge [0680]: Intel Corporation 82371AB/EB/MB PIIX4 ACPI [8086:7113]
(rev 02)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
00:0a.0 CardBus bridge [0607]: Ricoh Co Ltd RL5c475 [1180:0475] (rev 81)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 20020000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
Memory window 0: 10000000-13fff000 (prefetchable)
Memory window 1: 14000000-17fff000
I/O window 0: 00001000-000010ff
I/O window 1: 00001400-000014ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+
16-bit legacy interface ports at 0001
00:0c.0 VGA compatible controller [0300]: Number 9 Computer Company Revolution
4 [105d:5348] (rev 02) (prog-if 00 [VGA])
Subsystem: Number 9 Computer Company Unknown device [105d:0017]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e2000000 (32-bit, prefetchable) [size=32M]
Region 1: Memory at e0000000 (32-bit, prefetchable) [size=32M]
Region 2: Memory at df000000 (32-bit, non-prefetchable) [size=4K]
Region 4: Memory at de800000 (32-bit, non-prefetchable) [size=64K]
Region 5: I/O ports at d000 [size=256]
[virtual] Expansion ROM at 20000000 [disabled] [size=64K]
Capabilities: [80] AGP version 1.0
Status: RQ=16 Iso- ArqSz=0 Cal=0 SBA- ITACoh- GART64- HTrans-
64bit- FW- AGP3- Rate=x1,x2
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW-
Rate=<none>
Capabilities: [90] Power Management version 1
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0d.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ [10ec:8139] (rev 10)
Subsystem: OVISLINK Corp. LFE-8139ATX [149c:139a]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 7
Region 0: I/O ports at b800 [size=256]
Region 1: Memory at de000000 (32-bit, non-prefetchable) [size=256]
[virtual] Expansion ROM at 20010000 [disabled] [size=64K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0e.0 CardBus bridge [0607]: Ricoh Co Ltd RL5c475 [1180:0475] (rev 81)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 20021000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=06, subordinate=09, sec-latency=176
Memory window 0: 18000000-1bfff000 (prefetchable)
Memory window 1: 1c000000-1ffff000
I/O window 0: 00001800-000018ff
I/O window 1: 00001c00-00001cff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+
16-bit legacy interface ports at 0001
02:00.0 Network controller [0280]: Option N.V. Qualcomm MSM6275 UMTS chip
[1931:000c]
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 14000000 (32-bit, non-prefetchable) [size=2K]
06:00.0 USB Controller [0c03]: NEC Corporation USB [1033:0035] (rev 43)
(prog-if 10 [OHCI])
Subsystem: PSITech Unknown device [12d1:0035]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (250ns min, 10500ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 1c000000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
06:00.1 USB Controller [0c03]: NEC Corporation USB [1033:0035] (rev 43)
(prog-if 10 [OHCI])
Subsystem: PSITech Unknown device [12d1:0035]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (250ns min, 10500ns max)
Interrupt: pin B routed to IRQ 11
Region 0: Memory at 1c001000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
-- System Information:
Debian Release: lenny/sid
APT prefers unstable
APT policy: (500, 'unstable'), (500, 'testing'), (500, 'stable'), (1,
'experimental')
Architecture: i386 (i686)
Kernel: Linux 2.6.21-1-686 (SMP w/1 CPU core)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=locale: Cannot set
LC_CTYPE to default locale: No such file or directory
locale: Cannot set LC_MESSAGES to default locale: No such file or directory
locale: Cannot set LC_ALL to default locale: No such file or directory
ANSI_X3.4-1968)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.21-1-686 depends on:
ii initramfs-tools [linux-initr 0.88 tools for generating an initramfs
ii module-init-tools 3.3-pre11-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.21-1-686 recommends:
ii libc6-i686 2.5-9+b1 GNU C Library: Shared libraries [i
-- debconf information:
perl: warning: Setting locale failed.
perl: warning: Please check that your locale settings:
LANGUAGE = (unset),
LC_ALL = (unset),
LANG = "en_US.UTF-8"
are supported and installed on your system.
perl: warning: Falling back to the standard locale ("C").
locale: Cannot set LC_CTYPE to default locale: No such file or directory
locale: Cannot set LC_MESSAGES to default locale: No such file or directory
locale: Cannot set LC_ALL to default locale: No such file or directory
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.21-1-686/postinst/kimage-is-a-directory:
linux-image-2.6.21-1-686/prerm/removing-running-kernel-2.6.21-1-686: true
linux-image-2.6.21-1-686/preinst/lilo-initrd-2.6.21-1-686: true
linux-image-2.6.21-1-686/preinst/elilo-initrd-2.6.21-1-686: true
linux-image-2.6.21-1-686/postinst/depmod-error-2.6.21-1-686: false
linux-image-2.6.21-1-686/postinst/old-initrd-link-2.6.21-1-686: true
linux-image-2.6.21-1-686/preinst/lilo-has-ramdisk:
linux-image-2.6.21-1-686/preinst/abort-overwrite-2.6.21-1-686:
linux-image-2.6.21-1-686/postinst/bootloader-error-2.6.21-1-686:
linux-image-2.6.21-1-686/preinst/bootloader-initrd-2.6.21-1-686: true
linux-image-2.6.21-1-686/postinst/old-dir-initrd-link-2.6.21-1-686: true
linux-image-2.6.21-1-686/postinst/bootloader-test-error-2.6.21-1-686:
* linux-image-2.6.21-1-686/preinst/already-running-this-2.6.21-1-686:
linux-image-2.6.21-1-686/prerm/would-invalidate-boot-loader-2.6.21-1-686: true
linux-image-2.6.21-1-686/preinst/abort-install-2.6.21-1-686:
linux-image-2.6.21-1-686/postinst/depmod-error-initrd-2.6.21-1-686: false
linux-image-2.6.21-1-686/postinst/old-system-map-link-2.6.21-1-686: true
linux-image-2.6.21-1-686/preinst/failed-to-move-modules-2.6.21-1-686:
linux-image-2.6.21-1-686/preinst/initrd-2.6.21-1-686:
linux-image-2.6.21-1-686/postinst/create-kimage-link-2.6.21-1-686: true
linux-image-2.6.21-1-686/preinst/overwriting-modules-2.6.21-1-686: true
--- End Message ---
--- Begin Message ---
On Fri, Nov 07, 2008 at 09:25:09PM +0100, Moritz Muehlenhoff wrote:
> On Sat, Jun 02, 2007 at 09:04:02AM +0200, Miernik wrote:
> > I just downgraded the kernel to
> > linux-image-2.6.18-4-686 version 2.6.18.dfsg.1-12etch2
> > and the bug doesn't occur. So it must have been introduced somewhere
> > between 2.6.18.dfsg.1-12etch2 and 2.6.21-4. With 2.6.21-4 it is
> > reproducible every time. And not only 'statserial' triggers it, but also
> > for example running 'picocom' on /dev/ttyUSB2.
>
> Does this issue still occur with current kernels like the Lenny
> kernel?
No further feedback, closing the bug.
If anyone reencounters the problem, please reopen this bug.
Cheers,
Moritz
--- End Message ---
