On Sat, Jun 04, 2005 at 09:32:30PM +0300, Lior Kaplan wrote: > Hi Daniel, > > I need more info about a bug you reported. See > http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=267484 > > This is the second time I'm trying to contact you.
Sorry for the delay, I have not had the modem hooked up. I hooked it up just now and tried again, and got the same problem. Here is the session (calling card pin changed to XXXXXXXXX): ----- efax: 35:39 opened /dev/ttyS3 efax: 35:40 using Xircom CreditCard Modem CM-56T (Revision 1.49T) in class 1 efax: 35:41 dialing T7202462399,,,,XXXXXXXXXX,,,2063394363 efax: 36:29 connected efax: 36:32 Error: timed out reading frame data efax: 36:32 Error: wrong response to receive-frame command efax: 36:35 Warning: bit-reversed HDLC frame, reversing bit order efax: 36:32 received UNKNOWN efax: 36:32 received UNKNOWN efax: 36:35 received UNKNOWN efax: 36:35 remote ID -> K7FAX efax: 36:35 received DIS - answering capabilities efax: 36:35 remote has no document(s) to send, and can receive efax: 36:35 local 196lpi 14.4kbps 8.5"/215mm any 1D - - 0ms efax: 36:35 remote 196lpi 14.4kbps 8.5"/215mm any 2D - - 0ms efax: 36:35 session 196lpi 14.4kbps 8.5"/215mm any 1D - - 0ms efax: 36:36 sent TSI - caller ID efax: 36:36 sent DCS - session format efax: 36:40 sent TCF - channel check of 2700 bytes efax: 36:44 received CFR - channel OK efax: 36:45 header:[Sat 04-Jun-2005 17:35 From Daniel Webb (0000 00000) --> 7202462399,,,,XXXXXXXXXX,,,2063394363 p.1/1] efax: 37:13 sent 20+2156 lines, 51127+0 bytes, 28 s 14607 bps efax: 37:14 sent EOP - done efax: 37:17 received MCF - page OK efax: 37:17 sent -> /home/webb/speakeasy_rebate.ps.001 efax: 37:18 sent DCN - disconnect efax: 37:19 done, returning 0 (success) ----- Obviously, I don't want the header to say what it does, I just want: efax: 36:45 header:[Sat 04-Jun-2005 17:35 From Daniel Webb (0000 00000) p.1/1] instead of: efax: 36:45 header:[Sat 04-Jun-2005 17:35 From Daniel Webb (0000 00000) --> 7202462399,,,,XXXXXXXXXX,,,2063394363 p.1/1] Here is efax-gtkrc: ----- # efax-gtkrc -- configuration file for efax-gtk # Amend it as necessary and copy to $HOME/.efax-gtkrc, # /usr/local/etc/efax-gtkrc or /etc/efax-gtkrc. This file is searched # for in that order -- ie $HOME/.efax-gtkrc has priority over # /usr/local/etc/efax-gtkrc and /etc/efax-gtkrc # Anything preceded by a `#' character is treated as a comment and # ignored by the program. # Put your name to appear on the fax top header on sent faxes here NAME: Daniel Webb # Put your number to appear on the fax top header on sent faxes here # This will also comprise the fax station ID reported to the sending # fax machine when receiving faxes NUMBER: 0000 00000 # Put the serial device to which the modem is connected here (if none # is given or it is commented out, the program defaults to # /dev/modem). Do not include the `/dev/' part of the device name -- # ie state it as `ttyS1' or `cua2', etc. With Linux, ttyS0 equates to # COM 1, ttyS1 to COM 2, and so on DEVICE: ttyS3 # Put the lock file directory here. If none is given or it is # commented out, the program defaults to /var/lock. LOCK: /var/lock # With efax-0.9 you don't usually need to specify this, as efax will # work out the class of the modem. You should therefore usually leave # this commented out. However, with efax-0.8 the program defaults to # Class 2, so if you are using a Class 1 modem with old versions of # efax specify the Class here. Valid values are 1 for Class 1 modems # and 2.0 for Class 2.0 modems. With efax-0.9 you can also use the # value 2 to explicitly force the use of the Class 2 protocol #CLASS: 2 # Specify the page size here. Values accepted are `a4', `letter' or # `legal'. If none is specified the program defaults to a4. PAGE: letter # This specifies the resolution to which faxes are sent. Values # accepted are `standard' (204x98) and `fine' (204x196). If none is # given the program defaults to 204x196. RES: fine # This defines the number of rings the modem allows to pass before # answering the telephone when in Standby mode. Acceptable values are # 1 to 9. If none is specified, the program defaults to 1. RINGS: 1 # Valid values for the followinga are `tone' and `pulse'. If none is # specified, the program defaults to tone dialling. DIALMODE: tone # The following specifies the initialising `AT' commands for the modem # when in fax mode. Specify as many of these as are needed, separated # by spaces for commands to be separated, without a prepended `AT'. # If none is specified, the program will default to `Z &FE&D2S7=120 # &C0 M1L0', which will be correct for practically all modems INIT: Z &FE&D2S7=120 &C0 M1L0 # The following specifies the `AT' commands to reset the modem. # Specify as many of these as are needed, separated by spaces for # commands to be separated, without a prepended `AT'. If none is # specified, the program will default to `Z', which will be correct # for practically all modems RESET: Z # The following setting specifies the capabilities of the modem. To # see what these mean do `man efax', and look at the operation of the # `-c' flag. With efax-0.9 and a Class 2 modem, you usually won't # need to specify this and should leave it commented out, as the # program will interrogate the modem. If using an older version of # efax or a different class of modem, values which will work with # practically any 14,400 bps modem are 1,5,0,2,0,0,0,0, or # 1,3,0,2,0,0,0,0 for slower ones. #CAPABILITIES: 1,5,0,2,0,0,0,0 # The following is the command which prints and takes postscript input # on standard input. If none is specified, the program will default # to `lpr'. PRINT_CMD: lpr # The following will determine the extent to which a printed page will # be reduced to fit within a printer's print area. It is a percentage # -- eg 98 will shrink the page to 98% of its size. If none is # specified no shrink will take place (ie, there is no need to specify # `PRINT_SHRINK: 100'). Valid values are 50 to 100. PRINT_SHRINK: 98 # A postscript viewer is used to view sent and received faxes via the # fax lists, and also to view faxes to be sent identified via the # "Files to fax" file selector dialog. Specify here the command to be # used to view postscript files. If none is specified, the program # will default to 'gv'. Other possibilities you may want to specify # are 'ggv' (the Gnome postscript viewer) or 'kghostview' (the KDE # postscript viewer). If using gv, you may need to use the '-media # A4' or '-media Letter' option to select correct paper size. ggv # and kghosview do this automatically PS_VIEWER: gv # The following parameter specifies a log file to which progress on # negotiations and fax status, and errors and warnings, are logged. # If LOG_FILE is left commented out, or is given no value, then no log # file will be maintained. (A log file can also be kept by # redirecting stdout and stderr -- see the README file for further # details). #LOG_FILE: logfile # The following can be used to pass any other parameter to efax (do # `man efax' to see what is available). Specify as many of these as # are needed, separated by spaces for different parameters -- eg # include `-or' to do a bit reversal during receive for Multitech # modems which require it. Unless you have an unusual modem, leave # this blank or commented out #PARMS: ## end of efax-gtkrc ## -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
