Dave, Helge et al,
The 3.9 kernel installs and boots but wants to use the serial console
(OK I can do that). The displayed boot sequence stops at "Stopping
boot logger: bootlogd." but a power button shutdown will get a
response on the serial console. Please find attached the serial
console trace.
I need to go outside and clean bricks before forecast rain gets here
:-(.
Cheers,
Geoff.
----- Original Message -----
From:
To:
Cc:
Sent:
Subject:
Firmware Version 2.0
Duplex Console IO Dependent Code (IODC) revision 1
------------------------------------------------------------------------------
(c) Copyright 1995-2000, Hewlett-Packard Company, All rights reserved
------------------------------------------------------------------------------
Processor Speed State Coprocessor State I/D Cache
--------- -------- --------------------- ----------------- -------------
0 750 MHz Active Functional 768 kB/1536 kB
Central Bus Speed: 120 MHz
Available memory: 1073741824 bytes
Good memory required: 30945280 bytes
Primary boot path: FWSCSI.6.0
Alternate boot path: SCSI.6.0
Console path: GRAPHICS(2)
Keyboard path: USB
Processor is booting from first available device.
To discontinue, press any key within 10 seconds.
Boot terminated.
----- Main Menu -------------------------------------------------------------
Command Description
------- -----------
BOot [PRI|ALT|<path>] Boot from specified path
PAth [PRI|ALT|CON|KEY [<path>]] Display or modify a path
SEArch [DIsplay|[[IPL] [<path>]]] Search for boot devices
COnfiguration [<command>] Access Configuration menu/commands
INformation [<command>] Access Information menu/commands
SERvice [<command>] Access Service menu/commands
DIsplay Redisplay the current menu
HElp [<menu>|<command>] Display help for menu or command
RESET Restart the system
-----
Main Menu: Enter command > sea
Searching for potential boot device(s)...
This may take several minutes.
To discontinue search, press any key (termination may not be immediate).
Path Number Device Path Device Type
----------- ----------------- -----------
P0 IDE LITE-ON DVDRW SHM-165P6S
P1 FWSCSI.6.0 HP 18.2GMAN3184MC
Main Menu: Enter command > bo p1
Interact with IPL (Y, N, Q)?> y
Booting...
Boot IO Dependent Code (IODC) revision 0
HARD Booted.
palo ipl 1.14 root@penalosa Wed Oct 8 15:04:37 UTC 2008
Skipping extended partition 6 - beyond reach of IPL
Partition Start(MB) End(MB) Id Type
1 1 31 f0 Palo
2 32 156 83 ext2
5 157 16669 83 ext2
PALO(F0) partition contains:
0/vmlinux32 4188604 bytes @ 0x48000
Information: No console specified on kernel command line. This is normal.
PALO will choose the console currently used by firmware (serial).Current
command line:
2/vmlinux root=/dev/sda5 initrd=2/initrd.img HOME=/ console=ttyS0 TERM=vt102
0: 2/vmlinux
1: root=/dev/sda5
2: initrd=2/initrd.img
3: HOME=/
4: console=ttyS0
5: TERM=vt102
<#> edit the numbered field
'b' boot with this command line
'r' restore command line
'l' list dir
? 0 l
Directory listing of /.
lost+found
initrd.img
vmlinux
System.map-2.6.26-2-parisc
config-2.6.26-2-parisc
vmlinux-2.6.26-2-parisc
initrd.img-2.6.26-2-parisc
vmlinux-3.9
config.parisc-kernel-3.9
Current command line:
2/vmlinux root=/dev/sda5 initrd=2/initrd.img HOME=/ console=ttyS0 TERM=vt102
0: 2/vmlinux
1: root=/dev/sda5
2: initrd=2/initrd.img
3: HOME=/
4: console=ttyS0
5: TERM=vt102
<#> edit the numbered field
'b' boot with this command line
'r' restore command line
'l' list dir
? 0 2 0
2/vmlinux-3.9
Current command line:
2/vmlinux-3.9 root=/dev/sda5 initrd=2/initrd.img HOME=/ console=ttyS0 TERM=vt102
0: 2/vmlinux-3.9
1: root=/dev/sda5
2: initrd=2/initrd.img
3: HOME=/
4: console=ttyS0
5: TERM=vt102
<#> edit the numbered field
'b' boot with this command line
'r' restore command line
'l' list dir
? 0 2
initrd=2/initrd.img
Current command line:
2/vmlinux-3.9 root=/dev/sda5 HOME=/ console=ttyS0 TERM=vt102
0: 2/vmlinux-3.9
1: root=/dev/sda5
2: HOME=/
3: console=ttyS0
4: TERM=vt102
<#> edit the numbered field
'b' boot with this command line
'r' restore command line
'l' list dir
? 0 b
Command line for kernel: 'root=/dev/sda5 HOME=/ console=ttyS0 TERM=vt102
palo_kernel=2/vmlinux-3.9'
Selected kernel: /vmlinux-3.9 from partition 2
ELF64 executable
Entry 00100000 first 00100000 n 2
Segment 0 load 00100000 size 9170944 mediaptr 0x1000
Segment 1 load 00a3fe40 size 1206912 mediaptr 0x8c0e40
Branching to kernel entry point 0x00100000. If this is the last
message you see, you may need to switch your console. This is
a common symptom -- search the FAQ and mailing list at parisc-linux.org
[ 0.000000] Linux version 3.9.0-64bit+ (deller@ls3530) (gcc version 4.7.2
20121105 (Red Hat 4.7.2-2.aa.20121114svn) (GCC) ) #226 SMP Thu May 9 23:02:41
CEST 2013
[ 0.000000] unwind_init: start = 0x40884000, end = 0x408c9a00, entries =
17824
[ 0.000000] FP[0] enabled: Rev 1 Model 19
[ 0.000000] The 64-bit Kernel has started...
[ 0.000000] bootconsole [ttyB0] enabled
[ 0.000000] Initialized PDC Console for debugging.
[ 0.000000] Determining PDC firmware type: System Map.
[ 0.000000] model 00005dc0 00000481 00000000 00000002 77dc0ab2 100000f0
00000008 000000b2 000000b2
[ 0.000000] vers 00000203
[ 0.000000] CPUID vers 19 rev 7 (0x00000267)
[ 0.000000] capabilities 0x7
[ 0.000000] model 9000/785/C3700
[ 0.000000] Total Memory: 1024 MB
[ 0.000000] LCD display at fffffff0f05d0008,fffffff0f05d0000 registered
[ 0.000000] PERCPU: Embedded 10 pages/cpu @0000000041a88000 s10432 r8192
d22336 u40960
[ 0.000000] SMP: bootstrap CPU ID is 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total
pages: 258560
[ 0.000000] Kernel command line: root=/dev/sda5 HOME=/ console=ttyS0
TERM=vt102 palo_kernel=2/vmlinux-3.9
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.000000] Memory: 1019548k/1048576k available (6676k kernel code, 29028k
reserved, 2227k data, 348k init)
[ 0.000000] virtual kernel memory layout:
0.000000] vmalloc : 0x0000000000008000 - 0x000000003f000000 (1007 MB)
0.000000] memory : 0x0000000040000000 - 0x0000000080000000 (1024 MB)
0.000000] .init : 0x0000000040b10000 - 0x0000000040b67000 ( 348 kB)
0.000000] .data : 0x00000000407853b8 - 0x00000000409b22f0 (2227 kB)
0.000000] .text : 0x0000000040100000 - 0x00000000407853b8 (6676 kB)
[ 0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=8,
Nodes=8
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] CONFIG_RCU_FANOUT set to non-default value of 32
[ 0.000000] NR_IRQS:128
[ 0.000000] Console: colour dummy device 160x64
[ 0.056000] Calibrating delay loop... 1494.01 BogoMIPS (lpj=2988032)
[ 0.164000] pid_max: default: 32768 minimum: 301
[ 0.224000] Mount-cache hash table entries: 256
[ 0.284000] Brought up 1 CPUs
[ 0.324000] devtmpfs: initialized
[ 0.372000] atomic64 test passed
[ 0.416000] regulator-dummy: no parameters
[ 0.468000] NET: Registered protocol family 16
[ 0.528000] Searching for devices...
[ 0.804000] Found devices:
[ 0.840000] 1. Astro BC Runway Port at 0xfffffffffed00000 [10] { 12, 0x0,
0x582, 0x0000b }
[ 0.948000] 2. Elroy PCI Bridge at 0xfffffffffed30000 [10/0] { 13, 0x0,
0x782, 0x0000a }
[ 1.056000] 3. Elroy PCI Bridge at 0xfffffffffed32000 [10/1] { 13, 0x0,
0x782, 0x0000a }
[ 1.160000] 4. Elroy PCI Bridge at 0xfffffffffed38000 [10/4] { 13, 0x0,
0x782, 0x0000a }
[ 1.268000] 5. Elroy PCI Bridge at 0xfffffffffed3c000 [10/6] { 13, 0x0,
0x782, 0x0000a }
[ 1.372000] 6. Allegro W2 at 0xfffffffffffa0000 [32] { 0, 0x0, 0x5dc,
0x00004 }
[ 1.472000] 7. Memory at 0xfffffffffed10200 [49] { 1, 0x0, 0x09c, 0x00009 }
[ 1.560000] Enabling regular chassis codes support v0.05
[ 1.764000] CPU(s): 1 x PA8700 (PCX-W2) at 750.000000 MHz
[ 1.840000] Setting cache flush threshold to 180000 (1 CPUs online)
[ 1.948000] SBA found Astro 2.1 at 0xfffffffffed00000
[ 2.016000] Elroy version TR4.0 (0x5) found at 0xfffffffffed30000
[ 2.096000] LBA 10:0: PCI host bridge to bus 0000:00
[ 2.160000] pci_bus 0000:00: root bus resource [io 0x0000-0x1fff]
[ 2.244000] pci_bus 0000:00: root bus resource [mem
0xfffffffff4000000-0xfffffffff47fffff] (bus address [0xf4000000-0xf47fffff])
[ 2.396000] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 2.488000] PCI: Enabled native mode for NS87415 (pif=0x8f)
[ 2.564000] Elroy version TR4.0 (0x5) found at 0xfffffffffed32000
[ 2.644000] LBA 10:1: PCI host bridge to bus 0000:01
[ 2.712000] pci_bus 0000:01: root bus resource [io 0x12000-0x13fff] (bus
address [0x2000-0x3fff])
[ 2.828000] pci_bus 0000:01: root bus resource [mem
0xfffffffff4800000-0xfffffffff4ffffff] (bus address [0xf4800000-0xf4ffffff])
[ 2.980000] pci_bus 0000:01: root bus resource [??? 0x00000001 flags 0x0]
[ 3.072000] Elroy version TR4.0 (0x5) found at 0xfffffffffed38000
[ 3.152000] LBA 10:4: PCI host bridge to bus 0000:02
[ 3.216000] pci_bus 0000:02: root bus resource [io 0x28000-0x29fff] (bus
address [0x8000-0x9fff])
[ 3.336000] pci_bus 0000:02: root bus resource [mem
0xfffffffff6000000-0xfffffffff67fffff] (bus address [0xf6000000-0xf67fffff])
[ 3.488000] pci_bus 0000:02: root bus resource [??? 0x00000002 flags 0x0]
[ 3.576000] Elroy version TR4.0 (0x5) found at 0xfffffffffed3c000
[ 3.656000] LBA 10:6: PCI host bridge to bus 0000:03
[ 3.724000] pci_bus 0000:03: root bus resource [io 0x3c000-0x3dfff] (bus
address [0xc000-0xdfff])
[ 3.840000] pci_bus 0000:03: root bus resource [mem
0xfffffffffa000000-0xfffffffffbffffff] (bus address [0xfa000000-0xfbffffff])
[ 3.992000] pci_bus 0000:03: root bus resource [mem
0xfffffffff7000000-0xfffffffff77fffff] (bus address [0xf7000000-0xf77fffff])
[ 4.144000] pci_bus 0000:03: root bus resource [??? 0x00000003 flags 0x0]
[ 4.236000] iosapic: hpa not registered for 0000:03:02.0
[ 4.312000] powersw: Soft power switch at 0xfffffff0f0400804 enabled.
[ 4.400000] bio: create slab <bio-0> at 0
[ 4.456000] vgaarb: loaded
[ 4.492000] SCSI subsystem initialized
[ 4.540000] Switching to clocksource cr16
[ 4.600000] NET: Registered protocol family 2
[ 4.660000] TCP established hash table entries: 8192 (order: 5, 131072 bytes)
[ 4.752000] TCP bind hash table entries: 8192 (order: 5, 131072 bytes)
[ 4.840000] TCP: Hash tables configured (established 8192 bind 8192)
[ 4.924000] TCP: reno registered
[ 4.964000] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 5.044000] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 5.128000] NET: Registered protocol family 1
[ 5.184000] RPC: Registered named UNIX socket transport module.
[ 5.264000] RPC: Registered udp transport module.
[ 5.324000] RPC: Registered tcp transport module.
[ 5.388000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 5.472000] SuperIO: Found NS87560 Legacy I/O device at 0000:00:0e.1 (IRQ 68)
[ 5.564000] SuperIO: Serial port 1 at 0x3f8
[ 5.620000] SuperIO: Serial port 2 at 0x2f8
[ 5.676000] SuperIO: Parallel port at 0x378
[ 5.732000] SuperIO: Floppy controller at 0x3f0
[ 5.788000] SuperIO: ACPI at 0x7e0
[ 5.836000] SuperIO: USB regulator enabled
[ 5.944000] Enabling PDC chassis warnings support v0.05
[ 6.012000] Performance monitoring counters enabled for Allegro W2
[ 6.104000] VFS: Disk quotas dquot_6.5.2
[ 6.156000] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 6.244000] fuse init (API version 7.21)
[ 6.296000] msgmni has been set to 1991
[ 6.348000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major
252)
[ 6.448000] io scheduler noop registered
[ 6.496000] io scheduler cfq registered (default)
[ 6.564000] PDC Stable Storage facility v0.30
[ 6.956000] STI GSC/PCI core graphics driver Version 0.9a
[ 7.028000] sti 0000:03:02.0: enabling SERR and PARITY (0002 -> 0142)
[ 7.112000] STI PCI graphic ROM found at fffffffff7000000 (64 kB), fb at
fffffffffa000000 (32 MB)
[ 7.312000] Unable to handle STI device '0000:03:02.0'
[ 7.380000] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 7.460000] serial8250: ttyS0 at I/O 0x3f8 (irq = 3) is a 16550A
[ 7.540000] console [ttyS0] enabled, bootconsole disabled
[ 7.540000] console [ttyS0] enabled, bootconsole disabled
[ 7.676000] serial8250: ttyS1 at I/O 0x2f8 (irq = 4) is a 16550A
[ 7.752000] loop: module loaded
[ 7.788000] Uniform Multi-Platform E-IDE driver
[ 7.844000] Loading iSCSI transport class v2.0-870.
[ 7.904000] iscsi: registered transport (qla4xxx)
[ 7.960000] QLogic iSCSI HBA Driver
[ 8.196000] sym0: <896> rev 0x7 at pci 0000:00:0f.0 irq 69
[ 8.264000] sym0: PA-RISC Firmware, ID 7, Fast-40, SE, parity checking
[ 8.340000] sym0: SCSI BUS has been reset.
[ 8.396000] scsi0 : sym-2.2.3
[ 13.588000] sym1: <896> rev 0x7 at pci 0000:00:0f.1 irq 69
[ 13.656000] sym1: PA-RISC Firmware, ID 7, Fast-40, LVD, parity checking
[ 13.736000] sym1: SCSI BUS has been reset.
[ 13.792000] scsi1 : sym-2.2.3
[ 18.496000] scsi 1:0:6:0: Direct-Access HP 18.2G MAN3184MC HP07
PQ: 0 ANSI: 2
[ 18.592000] scsi target1:0:6: tagged command queuing enabled, command queue
depth 16.
[ 18.688000] scsi target1:0:6: Beginning Domain Validation
[ 18.756000] scsi target1:0:6: FAST-40 WIDE SCSI 80.0 MB/s ST (25 ns, offset
31)
[ 18.844000] scsi target1:0:6: Domain Validation skipping write tests
[ 18.920000] scsi target1:0:6: Ending Domain Validation
[ 21.372000] tun: Universal TUN/TAP device driver, 1.6
[ 21.432000] tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
[ 21.508000] Linux Tulip driver version 1.1.15 (Feb 27, 2007)
[ 21.584000] tulip0: no phy info, aborting mtable build
[ 21.644000] tulip0: MII transceiver #1 config 1000 status 782d advertising
01e1
[ 21.740000] net eth0: Digital DS21142/43 Tulip rev 65 at Port 0x1000,
00:30:6e:2b:67:6a, IRQ 66
[ 21.844000] LASI 82596 driver - Revision: 1.30
[ 21.900000] mousedev: PS/2 mouse device common for all mice
[ 21.968000] sd 1:0:6:0: [sda] 35566480 512-byte logical blocks: (18.2
GB/16.9 GiB)
[ 22.060000] rtc-generic rtc-generic: rtc core: registered rtc-generic as rtc0
[ 22.144000] Netfilter messages via NETLINK v0.30.
[ 22.200000] sd 1:0:6:0: [sda] Write Protect is off
[ 22.260000] TCP: cubic registered
[ 22.300000] NET: Registered protocol family 17
[ 22.352000] NET: Registered protocol family 33
[ 22.404000] Key type rxrpc registered
[ 22.448000] sd 1:0:6:0: [sda] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 22.556000] Key type rxrpc_s registered
[ 22.604000] registered taskstats version 1
[ 22.656000] rtc-generic rtc-generic: setting system clock to 2013-05-12
00:57:52 UTC (1368320272)
[ 22.800000] sda: sda1 sda2 sda3 < sda5 sda6 >
[ 22.868000] sd 1:0:6:0: [sda] Attached SCSI disk
[ 22.960000] kjournald starting. Commit interval 5 seconds
[ 23.028000] EXT3-fs (sda5): mounted filesystem with ordered data mode
[ 23.104000] VFS: Mounted root (ext3 filesystem) readonly on device 8:5.
[ 23.184000] Freeing unused kernel memory: 348k freed
modprobe: FATAL: Could not load /lib/modules/3.9.0-64bit+/modules.dep: No such
file or directory
INIT: version 2.86 booting
Starting the hotplug events dispatcher: udevd[ 26.936000] udevd (165):
/proc/165/oom_adj is deprecated, please use /proc/165/oom_score_adj instead.
.
Synthesizing the initial hotplug events...done.
Waiting for /dev to be fully populated...done.
Starting boot logger: bootlogd.
locale: Cannot set LC_CTYPE to default locale: No such file or directory
locale: Cannot set LC_ALL to default locale: No such file or directory
Usage: vt-is-UTF8 [option]
valid options are:
-q --quiet don't print result
-h --help display this help text and exit
-V --version display version information and exit
Activating swap...[ 33.728000] Adding 706824k swap on /dev/sda6. Priority:-1
extents:1 across:706824k
done.
Checking root file system...fsck from util-linux 2.20.1
/dev/sda5: clean, 19784/1058832 files, 246687/4227072 blocks
d[ 34.540000] EXT3-fs (sda5): using internal journal
one.
Cleaning up temporary files... /tmp /lib/init/rw.
Loading kernel module lasi_82596.
FATAL: Could not load /lib/modules/3.9.0-64bit+/modules.dep: No such file or
directory
Loading kernel module loop.
FATAL: Could not load /lib/modules/3.9.0-64bit+/modules.dep: No such file or
directory
FATAL: Could not load /lib/modules/3.9.0-64bit+/modules.dep: No such file or
directory
Activating lvm and md swap...done.
Checking file systems...fsck from util-linux 2.20.1
/dev/sda2: clean, 19/64256 files, 32964/128520 blocks
done.
Setting kernel variables (/etc/sysctl.conf)...done.
Mounting local filesystems...done.
/etc/rcS.d/S35mountall.sh: line 59: kill: 43 1: arguments must be process or
job IDs
Activating swapfile swap...done.
Cleaning up temporary files....
Configuring network interfaces...ifup: failed to open statefile
/run/network/ifstate: No such file or directory
failed.
Starting NFS common utilities: statd failed!
Cleaning up temporary files....
Setting console screen modes and fonts.
INIT: Entering runlevel: 2
Starting enhanced syslogd: rsyslogd.
Starting MTA: exim4.
ALERT: exim paniclog /var/log/exim4/paniclog has non-zero size, mail system
possibly broken ... failed!
Starting NFS common utilities: statd failed!
Not starting internet superserver: no services enabled.
Starting deferred execution scheduler: atd.
Starting periodic command scheduler: crond.
Stopping boot logger: bootlogd.
[ 1094.884000] kpowerswd: Shutdown requested...
[ 1097.932000] kpowerswd: Shutting down...
INIT:
IN
INIT: Sending processes the KILL signal
Stopping deferred execution scheduler: atd.
Stopping MTA:.
ALERT: exim paniclog /var/log/exim4/paniclog has non-zero size, mail system
possibly broken ... failed!
Stopping NFS common utilities: statd.
Stopping internet superserver: inetd.
Asking all remaining processes to terminate...done.
All processes ended within 1 seconds...done.
Saving the system clock.
Hardware Clock updated to Sun May 12 11:15:53 EST 2013.
Deconfiguring network interfaces...ifdown: failed to open statefile
/run/network/ifstate: No such file or directory
failed.
Deactivating swap...done.
Unmounting local filesystems...done.
Will now restart.
[ 1107.724000] sd 1:0:6:0: [sda] Synchronizing SCSI cache
[ 1107.784000] Restarting system.
