The log file...
Firmware Version 2.0
Duplex Console IO Dependent Code (IODC) revision 1
------------------------------------------------------------------------------
(c) Copyright 1995-2000, Hewlett-Packard Company, All rights reserved
------------------------------------------------------------------------------
Processor Speed State Coprocessor State I/D Cache
--------- -------- --------------------- ----------------- -------------
0 875 MHz Active Functional 768 kB/1536 kB
Central Bus Speed: 120 MHz
Available memory: 3221225472 bytes
Good memory required: 33366016 bytes
Primary boot path: FWSCSI.5.0
Alternate boot path: SCSI.6.0
Console path: SERIAL_1.9600.8.none
Keyboard path: USB
Processor is booting from first available device.
To discontinue, press any key within 10 seconds.
Boot terminated.
----- Main Menu -------------------------------------------------------------
Command Description
------- -----------
BOot [PRI|ALT|<path>] Boot from specified path
PAth [PRI|ALT|CON|KEY [<path>]] Display or modify a path
SEArch [DIsplay|[[IPL] [<path>]]] Search for boot devices
COnfiguration [<command>] Access Configuration menu/commands
INformation [<command>] Access Information menu/commands
SERvice [<command>] Access Service menu/commands
DIsplay Redisplay the current menu
HElp [<menu>|<command>] Display help for menu or command
RESET Restart the system
-----
Main Menu: Enter command > sea
Searching for potential boot device(s)...
This may take several minutes.
To discontinue search, press any key (termination may not be immediate).
Path Number Device Path Device Type
----------- ----------------- -----------
P0 LAN.10.23.1.2.3.254 10.23.1.2 100/Full Dx
P1 IDE HL-DT-STDVD-ROM GDR8162B
P2 FWSCSI.6.0 HP 73.4GST373405LC
P3 FWSCSI.5.0 HP 36.4GMAN3367MC
Main Menu: Enter command > in io
I/O MODULE INFORMATION
IODC IODC
Path Decimal Type Location HVER SVER Vers Dep
------------ ----------- --------------------- ---------- ---- ---- ---- ----
LAN 10/0/12/0 Ethernet built-in 0610 a200 0x02 0x00
AUDIO 10/0/13/0 Audio built-in
IDE 10/0/14/0 IDE built-in 0610 a300 0x00 0x00
SUPERIO MISC 10/0/14/1 Bridge Device built-in
SERIAL_1 10/0/14/1/1 RS232 Port built-in 0610 8c00 0x01 0x00
SERIAL_2 10/0/14/1/2 RS232 Port built-in 0610 8c00 0x01 0x00
PARALLEL 10/0/14/1/3 Parallel Port built-in
USB 10/0/14/2 USB built-in 0610 a900 0x98 0x00
SCSI 10/0/15/0 SCSI built-in 0610 a300 0x00 0x00
FWSCSI 10/0/15/1 SCSI built-in 0610 a300 0x00 0x00
PCI6 10/1/6/0 USB slot 6 (no firmware driver)
10/1/6/1 10/1/6/1 USB slot 6 (no firmware driver)
10/1/6/2 10/1/6/2 USB slot 6 (no firmware driver)
GRAPHICS(1) 10/4/1/0 A1262A slot 1 0070 8500 0x01 0x00
GRAPHICS(2) 10/6/2/0 A1262A slot 2 0070 8500 0x01 0x00
Main Menu: Enter command > bo lan
Interact with IPL (Y, N, Q)?> n
Booting...
Network Station Address 00306e-483da7
System IP Address 10.23.1.38
Server IP Address 10.23.1.2
Boot IO Dependent Code (IODC) revision 2
HARD Booted.
palo ipl 2.28 https://parisc.docs.kernel.org - Sat, 06 Sep 2025 10:01:23 +0000
Booting from media >2GB possible: NO
Boot image contains:
0/vmlinux64 9022832(0) bytes @ 0xe800
Information: No console specified on kernel command line. This is normal.
PALO will choose the console currently used by firmware (serial).
Command line for kernel: 'HOME=/ root=/dev/nfs nfsroot=10.23.1.2:/tftpboot/c3750/rootdir ip=10.23.1.38:10.23.1.2:10.23.1.2:255.255.255.0 nfsrootdebug init=/init rw console=ttyS0 TERM=vt102 palo_kernel=0/vmlinuz'
Selected kernel: /vmlinuz from partition 0
Warning: kernel name doesn't end with 32 or 64 -- Guessing...
This box can boot either 32 or 64-bit kernels...
Only see a 64-bit kernel, using that
ELF64 executable
Segment 0 load 0x000e0000 size 8967271 mediaptr 0x1000
Segment 1 load 0x015cb000 size 27108 mediaptr 0x88f000
Branching to kernel entry point 0x000e0000. If this is the last message you
see, you may need to switch your console. This is a common symptom -- search
the FAQ and mailing list at https://parisc.docs.kernel.org
Decompressing Linux... done.
Booting the kernel.
[ 0.000000] Linux version 6.18.0-rc4-64bit+ (chris@blitz) (hppa64-linux-gnu-gcc (GCC) 15.2.0, GNU ld (GNU Binutils for Debian) 2.45.50.20251209) #2 SMP Fri Jan 2 15:12:18 CET 2026
[ 0.000000] FP[0] enabled: Rev 1 Model 19
[ 0.000000] The 64-bit Kernel has started...
[ 0.000000] Kernel default page size is 4 KB. Huge pages disabled.
[ 0.000000] Determining PDC firmware type: System Map.
[ 0.000000] model 00005dc0 00000481 00000000 00000002 77b06784 100000f0 00000008 000000b2 000000b2 00000001
[ 0.000000] vers 00000301
[ 0.000000] CPUID vers 19 rev 11 (0x0000026b)
[ 0.000000] capabilities 0x7
[ 0.000000] HP-UX model name: 9000/785/C3750
[ 0.000000] Memory Ranges:
[ 0.000000] 0) Start 0x0000000000000000 End 0x00000000bfffffff Size 3072 MB
[ 0.000000] Total Memory: 3072 MB
[ 0.000000] PDT: type PDT_PDC, size 50, entries 0, status 2, dbe_loc 0xffffffffffffffff, good_mem 31 MB
[ 0.000000] PDT: Firmware reports all memory OK.
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x00000bffffffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x00000000bfffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x00000000bfffffff]
[ 0.000000] percpu: Embedded 35 pages/cpu s105184 r8192 d29984 u143360
[ 0.000000] SMP: bootstrap CPU ID is 0
[ 0.000000] Kernel command line: HOME=/ root=/dev/nfs nfsroot=10.23.1.2:/tftpboot/c3750/rootdir ip=10.23.1.38:10.23.1.2:10.23.1.2:255.255.255.0 nfsrootdebug init=/init rw console=ttyS0 TERM=vt102 palo_kernel=0/vmlinuz earlycon=pdc
[ 0.000000] earlycon: pdc0 at MMIO32be 0x0000000000000000 (options '')
[ 0.000000] printk: legacy bootconsole [pdc0] enabled
[ 0.000000] Unknown kernel command line parameters "palo_kernel=0/vmlinuz", will be passed to user space.
[ 0.000000] printk: log buffer data + meta data: 131072 + 458752 = 589824 bytes
[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[ 0.000000] Sorting __ex_table...
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 786432
[ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU event tracing is enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[ 0.000000] NR_IRQS: 128
[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000004] sched_clock: 64 bits at 875MHz, resolution 1ns, wraps every 4398046511103ns
[ 0.105335] clocksource: cr16: mask: 0xffffffffffffffff max_cycles: 0xc9cd436c30, max_idle_ns: 440795235170 ns
[ 0.237502] Console: colour dummy device 160x64
[ 0.297195] Calibrating delay loop... 1744.89 BogoMIPS (lpj=3489792)
[ 0.321202] pid_max: default: 32768 minimum: 301
[ 0.325859] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.329371] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.337805] TOC handler registered
[ 0.341478] rcu: Hierarchical SRCU implementation.
[ 0.345210] rcu: Max phase no-delay instances is 1000.
[ 0.350855] smp: Bringing up secondary CPUs ...
[ 0.353254] smp: Brought up 1 node, 1 CPU
[ 0.357486] Memory: 3059324K/3145728K available (13776K kernel code, 2852K rwdata, 3360K rodata, 648K init, 656K bss, 83840K reserved, 0K cma-reserved)
[ 0.363123] devtmpfs: initialized
[ 0.369068] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.369262] posixtimers hash table entries: 4096 (order: 4, 98304 bytes, linear)
[ 0.373868] futex hash table entries: 2048 (98304 bytes on 1 NUMA nodes, total 96 KiB, linear).
[ 0.380450] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.382173] audit: initializing netlink subsys (disabled)
[ 0.387137] Searching for devices...
[ 0.545200] Found devices:
[ 0.549205] 1. Astro BC Runway Port [10] at 0xfffffffffed00000 { type:12, hv:0x582, sv:0xb, rev:0x0 }
[ 0.553204] 2. Elroy PCI Bridge [10:0] at 0xfffffffffed30000 { type:13, hv:0x782, sv:0xa, rev:0x0 }
[ 0.557204] 3. Elroy PCI Bridge [10:1] at 0xfffffffffed32000 { type:13, hv:0x782, sv:0xa, rev:0x0 }
[ 0.561205] 4. Elroy PCI Bridge [10:4] at 0xfffffffffed38000 { type:13, hv:0x782, sv:0xa, rev:0x0 }
[ 0.565204] 5. Elroy PCI Bridge [10:6] at 0xfffffffffed3c000 { type:13, hv:0x782, sv:0xa, rev:0x0 }
[ 0.569205] 6. Allegro W2 [32] at 0xfffffffffffa0000 { type:0, hv:0x5dc, sv:0x4, rev:0x0 }
[ 0.573204] 7. Memory [49] at 0xfffffffffed10200 { type:1, hv:0x9c, sv:0x9, rev:0x0 }
[ 0.577215] Enabling regular chassis codes support v0.05
[ 0.585886] CPU0: cpu core 0 of socket 0
[ 0.589356] CPU(s): 1 out of 1 PA8700 (PCX-W2) at 875.000000 MHz online
[ 0.595429] alternatives: applied 1613 out of 1649 patches
[ 0.604933] Calculated flush threshold is 522 KiB
[ 0.605212] Cache flush threshold set to 1536 KiB
[ 0.609923] Whole TLB flush 5202 cycles, Range flush 21139456 bytes 622792 cycles
[ 0.613204] Calculated TLB flush threshold 176 KiB
[ 0.617200] TLB flush threshold set to 176 KiB
[ 0.629453] audit: type=2000 audit(1767478142.096:1): state=initialized audit_enabled=0 res=1
[ 0.633302] SBA found Astro 2.1 at 0xfffffffffed00000
[ 0.637559] Elroy version TR4.0 (0x5) found at 0xfffffffffed30000
[ 0.641496] LBA 10:0: PCI host bridge to bus 0000:00
[ 0.645213] pci_bus 0000:00: root bus resource [io 0x0000-0x1fff]
[ 0.649209] pci_bus 0000:00: root bus resource [mem 0xfffffffff4000000-0xfffffffff47fffff] (bus address [0xf4000000-0xf47fffff])
[ 0.653211] pci_bus 0000:00: root bus resource [bus 00]
[ 0.657417] pci 0000:00:0c.0: [1011:0019] type 00 class 0x020000 conventional PCI endpoint
[ 0.661543] pci 0000:00:0c.0: BAR 0 [io 0x1000-0x107f]
[ 0.665219] pci 0000:00:0c.0: BAR 1 [mem 0xfffffffff4008000-0xfffffffff40083ff]
[ 0.669258] pci 0000:00:0c.0: ROM [mem 0xfffffffff4040000-0xfffffffff407ffff pref]
[ 0.673808] pci 0000:00:0d.0: [11d4:1889] type 00 class 0x040100 conventional PCI endpoint
[ 0.677530] pci 0000:00:0d.0: BAR 0 [mem 0xfffffffff400c000-0xfffffffff400c1ff pref]
[ 0.681217] pci 0000:00:0d.0: BAR 1 [mem 0xfffffffff400b000-0xfffffffff400b00f pref]
[ 0.685217] pci 0000:00:0d.0: BAR 2 [mem 0xfffffffff400a000-0xfffffffff400a00f pref]
[ 0.689216] pci 0000:00:0d.0: BAR 3 [mem 0xfffffffff4009000-0xfffffffff400900f pref]
[ 0.693472] pci 0000:00:0d.0: supports D2
[ 0.697667] PCI: Enabled native mode for NS87415 (pif=0x8f)
[ 0.701208] pci 0000:00:0e.0: [100b:0002] type 00 class 0x01018f conventional PCI endpoint
[ 0.705524] pci 0000:00:0e.0: BAR 0 [io 0x0f00-0x0f07]
[ 0.709215] pci 0000:00:0e.0: BAR 1 [io 0x0e00-0x0e03]
[ 0.713215] pci 0000:00:0e.0: BAR 2 [io 0x0d00-0x0d07]
[ 0.717214] pci 0000:00:0e.0: BAR 3 [io 0x0b00-0x0b03]
[ 0.721214] pci 0000:00:0e.0: BAR 4 [io 0x0a00-0x0a0f]
[ 0.725695] pci 0000:00:0e.1: [100b:000e] type 00 class 0x068000 conventional PCI endpoint
[ 0.730064] pci 0000:00:0e.2: [100b:0012] type 00 class 0x0c0310 conventional PCI endpoint
[ 0.733538] pci 0000:00:0e.2: BAR 0 [mem 0xfffffffff4007000-0xfffffffff4007fff]
[ 0.737218] pci 0000:00:0e.2: BAR 1 [mem 0xfffffffff4006000-0xfffffffff4006fff]
[ 0.741795] pci 0000:00:0f.0: [1000:000b] type 00 class 0x010000 conventional PCI endpoint
[ 0.745530] pci 0000:00:0f.0: BAR 0 [io 0x0900-0x09ff]
[ 0.749227] pci 0000:00:0f.0: BAR 1 [mem 0xfffffffff4005000-0xfffffffff40053ff 64bit]
[ 0.753222] pci 0000:00:0f.0: BAR 3 [mem 0xfffffffff4002000-0xfffffffff4003fff 64bit]
[ 0.757458] pci 0000:00:0f.0: supports D1 D2
[ 0.761684] pci 0000:00:0f.1: [1000:000b] type 00 class 0x010000 conventional PCI endpoint
[ 0.765531] pci 0000:00:0f.1: BAR 0 [io 0x0800-0x08ff]
[ 0.769228] pci 0000:00:0f.1: BAR 1 [mem 0xfffffffff4004000-0xfffffffff40043ff 64bit]
[ 0.773227] pci 0000:00:0f.1: BAR 3 [mem 0xfffffffff4000000-0xfffffffff4001fff 64bit]
[ 0.777461] pci 0000:00:0f.1: supports D1 D2
[ 0.782329] Elroy version TR4.0 (0x5) found at 0xfffffffffed32000
[ 0.785438] LBA 10:1: PCI host bridge to bus 0000:01
[ 0.789215] pci_bus 0000:01: root bus resource [io 0x12000-0x13fff] (bus address [0x2000-0x3fff])
[ 0.793212] pci_bus 0000:01: root bus resource [mem 0xfffffffff4800000-0xfffffffff4ffffff] (bus address [0xf4800000-0xf4ffffff])
[ 0.797208] pci_bus 0000:01: root bus resource [bus 01]
[ 0.801363] pci 0000:01:06.0: [1033:0035] type 00 class 0x0c0310 conventional PCI endpoint
[ 0.805527] pci 0000:01:06.0: BAR 0 [mem 0xfffffffff4802000-0xfffffffff4802fff]
[ 0.809500] pci 0000:01:06.0: supports D1 D2
[ 0.813207] pci 0000:01:06.0: PME# supported from D0 D1 D2 D3hot
[ 0.817707] pci 0000:01:06.1: [1033:0035] type 00 class 0x0c0310 conventional PCI endpoint
[ 0.821529] pci 0000:01:06.1: BAR 0 [mem 0xfffffffff4801000-0xfffffffff4801fff]
[ 0.825500] pci 0000:01:06.1: supports D1 D2
[ 0.829206] pci 0000:01:06.1: PME# supported from D0 D1 D2 D3hot
[ 0.833695] pci 0000:01:06.2: [1033:00e0] type 00 class 0x0c0320 conventional PCI endpoint
[ 0.837529] pci 0000:01:06.2: BAR 0 [mem 0xfffffffff4800000-0xfffffffff48000ff]
[ 0.841499] pci 0000:01:06.2: supports D1 D2
[ 0.845206] pci 0000:01:06.2: PME# supported from D0 D1 D2 D3hot
[ 0.850044] Elroy version TR4.0 (0x5) found at 0xfffffffffed38000
[ 0.853390] LBA 10:4: PCI host bridge to bus 0000:02
[ 0.857221] pci_bus 0000:02: root bus resource [io 0x28000-0x29fff] (bus address [0x8000-0x9fff])
[ 0.861211] pci_bus 0000:02: root bus resource [mem 0xfffffffff8000000-0xfffffffff9ffffff] (bus address [0xf8000000-0xf9ffffff])
[ 0.865212] pci_bus 0000:02: root bus resource [mem 0xfffffffff6000000-0xfffffffff67fffff] (bus address [0xf6000000-0xf67fffff])
[ 0.869207] pci_bus 0000:02: root bus resource [bus 02]
[ 0.873277] pci 0000:02:01.0: [103c:1008] type 00 class 0x038000 conventional PCI endpoint
[ 0.877507] pci 0000:02:01.0: BAR 0 [mem 0xfffffffff8000000-0xfffffffff9ffffff 64bit]
[ 0.881254] pci 0000:02:01.0: ROM [mem 0xfffffffff6000000-0xfffffffff61fffff pref]
[ 0.885850] iosapic: hpa not registered for 0000:02:01.0
[ 0.889319] Elroy version TR4.0 (0x5) found at 0xfffffffffed3c000
[ 0.893455] LBA 10:6: PCI host bridge to bus 0000:03
[ 0.897212] pci_bus 0000:03: root bus resource [io 0x3c000-0x3dfff] (bus address [0xc000-0xdfff])
[ 0.901210] pci_bus 0000:03: root bus resource [mem 0xfffffffffa000000-0xfffffffffbffffff] (bus address [0xfa000000-0xfbffffff])
[ 0.905209] pci_bus 0000:03: root bus resource [mem 0xfffffffff7000000-0xfffffffff77fffff] (bus address [0xf7000000-0xf77fffff])
[ 0.909207] pci_bus 0000:03: root bus resource [bus 03]
[ 0.913282] pci 0000:03:02.0: [103c:1008] type 00 class 0x038000 conventional PCI endpoint
[ 0.917486] pci 0000:03:02.0: BAR 0 [mem 0xfffffffffa000000-0xfffffffffbffffff 64bit]
[ 0.921251] pci 0000:03:02.0: ROM [mem 0xfffffffff7000000-0xfffffffff71fffff pref]
[ 0.925818] iosapic: hpa not registered for 0000:03:02.0
[ 0.933202] powersw: Soft power switch at 0xfffffff0f0400804 enabled.
[ 0.940627] iommu: Default domain type: Translated
[ 0.941206] iommu: DMA domain TLB invalidation policy: strict mode
[ 0.945877] SCSI subsystem initialized
[ 0.950025] usbcore: registered new interface driver usbfs
[ 0.953314] usbcore: registered new interface driver hub
[ 0.957290] usbcore: registered new device driver usb
[ 0.963470] vgaarb: loaded
[ 0.966045] clocksource: Switched to clocksource cr16
[ 1.032248] VFS: Disk quotas dquot_6.6.0
[ 1.083827] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 1.189712] NET: Registered PF_INET protocol family
[ 1.255177] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 1.358612] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 49152 bytes, linear)
[ 1.471022] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 1.572919] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear)
[ 1.677946] TCP bind hash table entries: 32768 (order: 8, 1572864 bytes, linear)
[ 1.779059] TCP: Hash tables configured (established 32768 bind 32768)
[ 1.865544] UDP hash table entries: 2048 (order: 5, 229376 bytes, linear)
[ 1.955378] UDP-Lite hash table entries: 2048 (order: 5, 229376 bytes, linear)
[ 2.051311] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 2.126937] RPC: Registered named UNIX socket transport module.
[ 2.204785] RPC: Registered udp transport module.
[ 2.266644] RPC: Registered tcp transport module.
[ 2.328529] RPC: Registered tcp-with-tls transport module.
[ 2.400698] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 2.485464] PCI: CLS 16 bytes
[ 2.524596] SuperIO: Found NS87560 Legacy I/O device at 0000:00:0e.1 (IRQ 68)
[ 2.618497] SuperIO: Serial port 1 at 0x3f8
[ 2.673497] SuperIO: Serial port 2 at 0x2f8
[ 2.728509] SuperIO: Parallel port at 0x378
[ 2.783525] SuperIO: Floppy controller at 0x3f0
[ 2.843114] SuperIO: ACPI at 0x7e0
[ 2.887947] SuperIO: USB regulator enabled
[ 2.941868] pci 0000:00:0e.1: superio_init+0x0/0x748 took 407554 usecs
[ 3.032922] Enabling PDC chassis warnings support v0.05
[ 3.102589] Performance monitoring counters enabled for Allegro W2 [32]
[ 3.191127] workingset: timestamp_bits=46 max_order=20 bucket_order=0
[ 3.277093] NFS: Registering the id_resolver key type
[ 3.343613] Key type id_resolver registered
[ 3.398588] Key type id_legacy registered
[ 3.451311] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 3.539495] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[ 3.637239] fuse: init (API version 7.45)
[ 3.690976] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 3.788263] io scheduler mq-deadline registered
[ 3.847832] io scheduler kyber registered
[ 3.902961] PDC Stable Storage facility v0.30
[ 4.296967] sticore: STI GSC/PCI core graphics driver Version 0.9c
[ 4.378403] sticore: STI PCI graphic ROM found at fffffffff6000000 (2048 kB), fb at fffffffff8000000 (32 MB)
[ 4.577544] sticore: STI word mode ROM supports 32 and 64 bit firmware functions.
[ 4.675973] sticore: id 35acda30-9a02587, conforms to spec rev. 8.0d
[ 4.761863] sticore: built-in font #1: size 10x20, chars 0-255, bpc 40
[ 4.852341] sticore: built-in font #2: size 8x16, chars 0-255, bpc 16
[ 4.941678] sticore: using 8x16 framebuffer font VGA8x16
[ 5.016158] sticore: using 64-bit STI ROM functions
[ 5.215387] sticore: graphics card name: A1262A
[ 5.279573] sticore: located at [10/4/1/0]
[ 5.338124] sticore: STI PCI graphic ROM found at fffffffff7000000 (2048 kB), fb at fffffffffa000000 (32 MB)
[ 5.530687] sticore: STI word mode ROM supports 32 and 64 bit firmware functions.
[ 5.629100] sticore: id 35acda30-9a02587, conforms to spec rev. 8.0d
[ 5.715001] sticore: built-in font #1: size 10x20, chars 0-255, bpc 40
[ 5.805479] sticore: built-in font #2: size 8x16, chars 0-255, bpc 16
[ 5.894814] sticore: using 8x16 framebuffer font VGA8x16
[ 5.969290] sticore: using 64-bit STI ROM functions
[ 6.164183] sticore: graphics card name: A1262A
[ 6.228340] sticore: located at [10/6/2/0]
[ 6.286940] sticon: Initializing STI text console on A1262A at [10/4/1/0]
[ 6.376414] Console: switching consoles 1-63 to colour STI console 160x64
[ 6.641000] stifb: 'A1262A' (id: 0x35acda30) not supported.
[ 6.714356] stifb: 'A1262A' (id: 0x35acda30) not supported.
[ 6.787654] IPMI message handler: version 39.2
[ 6.846162] ipmi device interface
[ 6.889976] ipmi_si: IPMI System Interface driver
[ 6.952295] ipmi_si: Unable to find any System Interface(s)
[ 7.025962] Serial: 8250/16550 driver, 8 ports, IRQ sharing enabled
[ 7.108795] serial8250: ttyS0 at I/O 0x3f8 (irq = 3, base_baud = 115200) is a 16550A
[ 7.210814] printk: legacy console [ttyS0] enabled
[ 7.210814] printk: legacy console [ttyS0] enabled
[ 7.331236] printk: legacy bootconsole [pdc0] disabled
[ 7.331236] printk: legacy bootconsole [pdc0] disabled
[ 7.461056] serial8250: ttyS1 at I/O 0x2f8 (irq = 4, base_baud = 115200) is a 16550A
[ 7.557743] Linux agpgart interface v0.103
[ 7.606848] quicksilver: No Pluto found, so no AGPGART for you.
[ 7.677878] [drm] radeon kernel modesetting enabled.
[ 7.755281] loop: module loaded
[ 7.793013] Loading iSCSI transport class v2.0-870.
[ 8.076599] sym0: <896> rev 0x7 at pci 0000:00:0f.0 irq 69
[ 8.144917] sym0: PA-RISC Firmware, ID 7, Fast-40, SE, parity checking
[ 8.227110] sym0: SCSI BUS has been reset.
[ 8.278987] scsi host0: sym-2.2.3
[ 13.722999] sym1: <896> rev 0x7 at pci 0000:00:0f.1 irq 69
[ 13.791299] sym1: PA-RISC Firmware, ID 7, Fast-40, LVD, parity checking
[ 13.874499] sym1: SCSI BUS has been reset.
[ 13.926285] scsi host1: sym-2.2.3
[ 18.557104] scsi 1:0:5:0: Direct-Access HP 36.4G MAN3367MC HP05 PQ: 0 ANSI: 2
[ 18.654032] scsi target1:0:5: tagged command queuing enabled, command queue depth 16.
[ 18.747973] scsi target1:0:5: Beginning Domain Validation
[ 18.815603] scsi target1:0:5: FAST-40 WIDE SCSI 80.0 MB/s ST (25 ns, offset 31)
[ 18.904637] scsi target1:0:5: Domain Validation skipping write tests
[ 18.980758] scsi target1:0:5: Ending Domain Validation
[ 19.049508] scsi 1:0:6:0: Direct-Access HP 73.4G ST373405LC HP04 PQ: 0 ANSI: 2
[ 19.146478] scsi target1:0:6: tagged command queuing enabled, command queue depth 16.
[ 19.240353] scsi target1:0:6: Beginning Domain Validation
[ 19.321225] scsi target1:0:6: FAST-40 WIDE SCSI 80.0 MB/s ST (25 ns, offset 31)
[ 19.416512] scsi target1:0:6: Domain Validation skipping write tests
[ 19.492635] scsi target1:0:6: Ending Domain Validation
[ 21.947925] mpt3sas version 54.100.00.00 loaded
[ 22.007124] sd 1:0:5:0: Power-on or device reset occurred
[ 22.072309] scsi host2: pata_ns87415
[ 22.115650] sd 1:0:6:0: Power-on or device reset occurred
[ 22.181110] sd 1:0:5:0: [sda] 71132960 512-byte logical blocks: (36.4 GB/33.9 GiB)
[ 22.272074] scsi host3: pata_ns87415
[ 22.315107] sd 1:0:6:0: [sdb] 143374738 512-byte logical blocks: (73.4 GB/68.4 GiB)
[ 22.407216] ata1: PATA max MWDMA2 cmd 0xf00 ctl 0xe00 bmdma 0xa00 irq 7 lpm-pol 0
[ 22.496865] ata2: PATA max MWDMA2 cmd 0xd00 ctl 0xb00 bmdma 0xa08 irq 7 lpm-pol 0
[ 22.587176] tun: Universal TUN/TAP device driver, 1.6
[ 22.647880] sd 1:0:5:0: [sda] Write Protect is off
[ 22.705335] sd 1:0:6:0: [sdb] Write Protect is off
[ 22.763843] sd 1:0:5:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 22.880570] tulip0: no phy info, aborting mtable build
[ 22.942835] tulip0: MII transceiver #1 config 1000 status 782d advertising 01e1
[ 23.039790] net eth0: Digital DS21142/43 Tulip rev 65 at Port 0x1000, 00:30:6e:48:3d:a7, IRQ 66
[ 23.144229] e1000: Intel(R) PRO/1000 Network Driver
[ 23.202649] e1000: Copyright (c) 1999-2006 Intel Corporation.
[ 23.271652] LASI 82596 driver - Revision: 1.30
[ 23.324956] Fusion MPT base driver 3.04.20
[ 23.374033] Copyright (c) 1999-2008 LSI Corporation
[ 23.432505] Fusion MPT SPI Host driver 3.04.20
[ 23.485903] Fusion MPT SAS Host driver 3.04.20
[ 23.539782] sd 1:0:6:0: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA
[ 23.645506] ehci-pci 0000:01:06.2: EHCI Host Controller
[ 23.708154] ehci-pci 0000:01:06.2: new USB bus registered, assigned bus number 1
[ 23.797019] ehci-pci 0000:01:06.2: irq 72, io mem 0xfffffffff4800000
[ 23.885179] ehci-pci 0000:01:06.2: USB 2.0 started, EHCI 0.95
[ 23.955827] hub 1-0:1.0: USB hub found
[ 24.002967] hub 1-0:1.0: 5 ports detected
[ 24.051866] sd 1:0:6:0: [sdb] Attached SCSI disk
[ 24.108802] ohci-pci 0000:00:0e.2: OHCI PCI host controller
[ 24.175639] ohci-pci 0000:00:0e.2: new USB bus registered, assigned bus number 2
[ 24.264542] ohci-pci 0000:00:0e.2: irq 1, io mem 0xfffffffff4007000
[ 24.349114] sd 1:0:5:0: [sda] Attached SCSI disk
[ 24.453374] hub 2-0:1.0: USB hub found
[ 24.498387] hub 2-0:1.0: 3 ports detected
[ 24.547583] ohci-pci 0000:01:06.0: OHCI PCI host controller
[ 24.614371] ohci-pci 0000:01:06.0: new USB bus registered, assigned bus number 3
[ 24.703118] ohci-pci 0000:01:06.0: irq 70, io mem 0xfffffffff4802000
[ 24.780519] ata1.00: ATAPI: HL-DT-STDVD-ROM GDR8162B, 0018, max UDMA/44
[ 25.423602] hub 3-0:1.0: USB hub found
[ 25.468711] hub 3-0:1.0: 3 ports detected
[ 25.517743] ohci-pci 0000:01:06.1: OHCI PCI host controller
[ 25.584564] ohci-pci 0000:01:06.1: new USB bus registered, assigned bus number 4
[ 25.673257] ohci-pci 0000:01:06.1: irq 71, io mem 0xfffffffff4801000
[ 26.316855] hub 4-0:1.0: USB hub found
[ 26.361876] hub 4-0:1.0: 2 ports detected
[ 26.413200] rtc-generic rtc-generic: registered as rtc0
[ 26.477471] rtc-generic rtc-generic: setting system clock to 2026-01-03T22:09:39 UTC (1767478179)
[ 26.583918] hid: raw HID events driver (C) Jiri Kosina
[ 26.647206] usbcore: registered new interface driver usbhid
[ 26.713923] usbhid: USB HID core driver
[ 26.760466] NET: Registered PF_INET6 protocol family
[ 26.822111] Segment Routing with IPv6
[ 26.866083] In-situ OAM (IOAM) with IPv6
[ 26.913192] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 26.985425] NET: Registered PF_PACKET protocol family
[ 27.045980] Key type dns_resolver registered
[ 27.132825] registered taskstats version 1
[ 27.203215] usb 2-1: new low-speed USB device number 2 using ohci-pci
[ 27.517971] input: Adomax USB/PS2 Scroll Mouse as /devices/parisc/10/10:0/pci0000:00/0000:00:0e.2/usb2/2-1/2-1:1.0/0003:04B4:0202.0001/input/input0
[ 27.677419] hid-generic 0003:04B4:0202.0001: input,hidraw0: USB HID v1.10 Mouse [Adomax USB/PS2 Scroll Mouse] on usb-0000:00:0e.2-1/input0
[ 27.942332] usb 3-3: new full-speed USB device number 2 using ohci-pci
[ 28.084579] usb 2-2: new low-speed USB device number 3 using ohci-pci
[ 28.281722] usb 3-3: device descriptor read/64, error -52
[ 28.456201] input: DELL Dell USB Entry Keyboard as /devices/parisc/10/10:0/pci0000:00/0000:00:0e.2/usb2/2-2/2-2:1.0/0003:413C:2107.0002/input/input1
[ 28.672390] hid-generic 0003:413C:2107.0002: input,hidraw1: USB HID v1.11 Keyboard [DELL Dell USB Entry Keyboard] on usb-0000:00:0e.2-2/input0
[ 28.949550] usb 3-3: device descriptor read/64, error -52
[ 29.302342] usb 3-3: new full-speed USB device number 3 using ohci-pci
[ 29.568586] usb 3-3: device descriptor read/64, error -52
[ 29.925323] usb 3-3: device descriptor read/64, error -52
[ 30.094030] usb usb3-port3: attempt power cycle
[ 32.276889] ata1.00: qc timeout after 5000 msecs (cmd 0xa0)
[ 32.343639] ata1.00: TEST_UNIT_READY failed (err_mask=0x5)
[ 37.781616] ata1.00: qc timeout after 5000 msecs (cmd 0xa0)
[ 37.848335] ata1.00: TEST_UNIT_READY failed (err_mask=0x4)
[ 37.914066] ata1.00: limiting speed to MWDMA2:PIO3
[ 43.339662] ata1.00: qc timeout after 5000 msecs (cmd 0xa0)
[ 43.406394] ata1.00: TEST_UNIT_READY failed (err_mask=0x4)
[ 43.472114] ata1.00: disable device
[ 43.863835] IP-Config: Complete:
[ 43.902459] device=eth0, hwaddr=00:30:6e:48:3d:a7, ipaddr=10.23.1.38, mask=255.255.255.0, gw=10.23.1.2
[ 44.019139] host=10.23.1.38, domain=, nis-domain=(none)
[ 44.086945] bootserver=10.23.1.2, rootserver=10.23.1.2, rootpath=
[ 44.088574] check access for rdinit=/init failed: -2, ignoring
[ 44.258874] VFS: Mounted root (nfs filesystem) on device 0:15.
[ 44.329505] devtmpfs: mounted
[ 44.366814] Freeing unused kernel image (initmem) memory: 648K
[ 44.436773] Write protecting the kernel read-only data: 3360k
[ 44.506571] Run /init as init process
[ 47.715840] net eth0: Setting full-duplex based on MII#1 link partner capability of c5e1
[ 50.001665] tulip 0000:00:0c.0 enp0s12: renamed from eth0 (while UP)
[ 50.502583] random: crng init done
Starting system log daemon: syslogd, klogd.
mount: mounting 10.23.1.2:/tftpboot/c3750/rootdir on / failed: Invalid argument
ln: /usr/share/keyrings/archive.pgp: File exists
haveged: command socket is listening at fd 3
/etc/screenrc: unknown command 'deflogin' /etc/screenrc: bind: unknown command 'login'
[ (-*) ][ Jan 03 22:10 ]
[ (0*start) ][ Jan 03 22:10 ]
[ (0*start) ][ Jan 03 22:10 ]
[ (0*start) ][ Jan 03 22:10 ]
[ (0*start) ][ Jan 03 22:10 ] [ (0*start) ][ Jan 03 22:10 ][ (0*start) ][ Jan 03 22:10 ]
[ 0- start (2*shell) ][ Jan 03 22:10 ]
[ 0- start (2*shell) ][ Jan 03 22:10 ]
[ 0- start (2*shell) ][ Jan 03 22:10 ]
[ 0- start (2*shell) ][ Jan 03 22:10 ] [ 0- start (2*shell) ][ Jan 03 22:10 ][ 0- start (2*shell) ][ Jan 03 22:10 ]
[ 0 start 2- shell (3*shell) ][ Jan 03 22:10 ]
[ 0 start 2- shell (3*shell) ][ Jan 03 22:10 ]
[ 0 start 2- shell (3*shell) ][ Jan 03 22:10 ]
[ 0 start 2- shell (3*shell) ][ Jan 03 22:10 ] [ 0 start 2- shell (3*shell) ][ Jan 03 22:10 ][ 0 start 2- shell (3*shell) ][ Jan 03 22:10 ]
[ 0 start 2 shell 3- shell (4*log) ][ Jan 03 22:10 ]
[ 0 start 2 shell 3- shell (4*log) ][ Jan 03 22:10 ]
[ 0 start 2 shell 3- shell (4*log) ][ Jan 03 22:10 ]
[ 0 start 2 shell 3- shell (4*log) ][ Jan 03 22:10 ] [ 0 start 2 shell 3- shell (4*log) ][ Jan 03 22:10 ][ 0 start 2 shell 3- shell (4*log) ][ Jan 03 22:10 ]
[ 0 start (1*shell) 2 shell 3 shell 4- log ][ Jan 03 22:10 ]
[ 0 start (1*shell) 2 shell 3 shell 4- log ][ Jan 03 22:10 ]
[ 0 start (1*shell) 2 shell 3 shell 4- log ][ Jan 03 22:10 ]
[ 0 start (1*shell) 2 shell 3 shell 4- log ][ Jan 03 22:10 ] [ 0 start (1*shell) 2 shell 3 shell 4- log ][ Jan 03 22:10 ][ 0 start (1*shell) 2 shell 3 shell 4- log ][ Jan 03 22:10 ]
[ (1*shell) 2 shell 3 shell 4- log ][ Jan 03 22:10 ]
[ (1*installer) 2 shell 3 shell 4- log ][ Jan 03 22:10 ]
[ (1*installer) 2 shell 3 shell 4- log ][ Jan 03 22:10 ]
lqqqqqqu [!!] Load installer components from installation media tqqqqqqqkx x x There was a problem reading data. Please make sure you have inserted x x the installation media correctly. If retrying does not work, you x x should check the integrity of your installation media (there is an x x associated entry in the main menu for that). x x x x Failed to copy file from installation media. Retry? x x x x <Yes> <No> x x x mqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqj <Tab> moves; <Space> selects; <Enter> activates buttons
