On Thu, 20 Jan 2005, Yuval Tanny wrote: > No. I didn't run it at all. The guide say: "Once you are presented with > a shell prompt, and any time that the Hurd is in single user mode, it is > necessary to set the terminal type:". I hadn't presented with a shell > prompt in the GNU/Hurd system, yet. Should I chroot to in and run it > (twice?)?
You will need to boot into your Hurd system to run ./native-install. This needs to be done twice. > > (I'm not using the K8 installer...) The tarball is very similar to baseGNU on the CD set. Phil. > > Thanks, > > Yuval > > > Philip Charles wrote: > > >Yuval, > > Have you run ./native-install twice? > > > >Phil. > > > >On Thu, 20 Jan 2005, Yuval Tanny wrote: > > > > > > > >>Hello, > >> > >> > >>After following this: > >> > >>http://www.debian.org/ports/hurd/hurd-install > >> > >>installation guide, I get this message at boot: > >> > >>(this is what I see on the screen) > >> > >> > >>ide0 at 0x1f0-0x1f7, 0x3f6 on irq 14 > >> > >>ide1 at 0x170-0x177, 0x3f6 on irq 15 > >> > >>Floppy... > >> > >>FDC is a post 1991 82077 > >> > >>Failed initialization of WD-7000 SCSI card! > >> > >>EATAO, address 0x1f0 in use skipping probe. > >> > >>EATAO, address 0x170 in use skipping probe. > >> > >>ppa: Version 1.42 > >> > >>ppa: Probing port 03bc > >> > >>ppa: Probing port 0378 > >> > >>...(and some other lines from ppa).. > >> > >>scsi: 0 hosts. > >> > >>scsi: detected total. > >> > >>rtl8139.c:B1.23a ... > >> > >> http:///www... > >> > >>eth0: RealTek RTL81396 Fast Ethernet at 0xa00 IRQ 10, 0:e0:ud: 7:98:ca > >> > >>Now the system lock. It's not responding. > >> > >> > >>I installed from debian-gnu-hurd-2004.12.30.tar.gz. I have ABIT NF7-S > >>(nforce 2 with SCSI controller that is in no use) motherboard, WD800JB > >>hard disc (ATA connected), the Debian GNU/Hurd is on hda1or hd0s1 (I > >>hope :-) ), It's a 6 GB (maybe this is it?) ext2 hurd partition. > >> > >> > >>What is the problem and how can I fix it? > >> > >> > >>I'll be glade to give more info, > >> > >>Thanks, > >> > >>Yuval > >> > >> > >>-- > >>To UNSUBSCRIBE, email to [EMAIL PROTECTED] > >>with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED] > >> > >> > >> > >> > > > >-- > > Philip Charles; 39a Paterson Street, Abbotsford, Dunedin, New Zealand > > +64 3 488 2818 Fax +64 3 488 2875 Mobile 025 267 9420 > > [EMAIL PROTECTED] - preferred. [EMAIL PROTECTED] > > I sell GNU/Linux & GNU/Hurd CDs & DVDs. See http://www.copyleft.co.nz > > > > > > > > > > -- Philip Charles; 39a Paterson Street, Abbotsford, Dunedin, New Zealand +64 3 488 2818 Fax +64 3 488 2875 Mobile 025 267 9420 [EMAIL PROTECTED] - preferred. [EMAIL PROTECTED] I sell GNU/Linux & GNU/Hurd CDs & DVDs. See http://www.copyleft.co.nz -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
