Your message dated Sat, 01 May 2021 08:09:06 -0700 (PDT) with message-id <[email protected]> and subject line Closing this bug (BTS maintenance for src:linux bugs) has caused the Debian Bug report #701620, regarding linux-image-3.2.0-4-amd64: Unable to use PCI cards on Intel DZ77SL50K motherboard (likely any Z77 board) to be marked as done.
This means that you claim that the problem has been dealt with. If this is not the case it is now your responsibility to reopen the Bug report if necessary, and/or fix the problem forthwith. (NB: If you are a system administrator and have no idea what this message is talking about, this may indicate a serious mail system misconfiguration somewhere. Please contact [email protected] immediately.) -- 701620: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=701620 Debian Bug Tracking System Contact [email protected] with problems
--- Begin Message ---Package: src:linux Version: 3.2.35-2 Severity: important Tags: upstream Dear Maintainer, I am unable to use any of my PCI slots of my new motherboard (a recent HW upgrade). Tested with two PCI network cards (1. Atheros chip based WiFi card I used with my previous mobo for WiFi AP, and 2. a 3Com NIC) placed repeatedly in different PCI slots. The results were always the same: 1. during boot the kernel loads the appropriate modules (e.g. 3c59x), all appears to look just fine in dmesg. 2. unless I bring the interfaces associated with the network cards up, everything works as expected. 3. the moment I issue the 'ifup ethX' command, the following is printed in /var/log/syslog: Feb 23 22:02:39 poo avahi-daemon[2437]: Joining mDNS multicast group on interface eth1.IPv4 with address 192.168.1.1. Feb 23 22:02:39 poo NetworkManager[4070]: <info> (eth1): carrier now ON (device state 10) Feb 23 22:02:39 poo kernel: [ 669.071740] eth1: setting full-duplex. Feb 23 22:02:39 poo avahi-daemon[2437]: New relevant interface eth1.IPv4 for mDNS. Feb 23 22:02:39 poo avahi-daemon[2437]: Registering new address record for 192.168.1.1 on eth1.IPv4. Feb 23 22:02:40 poo avahi-daemon[2437]: Joining mDNS multicast group on interface eth1.IPv6 with address fe80::210:5aff:fec0:2aab. Feb 23 22:02:40 poo avahi-daemon[2437]: New relevant interface eth1.IPv6 for mDNS. Feb 23 22:02:40 poo avahi-daemon[2437]: Registering new address record for fe80::210:5aff:fec0:2aab on eth1.*. Feb 23 22:02:41 poo ntpd[2294]: Listen normally on 9 eth1 192.168.1.1 UDP 123 Feb 23 22:02:41 poo ntpd[2294]: Listen normally on 10 eth1 fe80::210:5aff:fec0:2aab UDP 123 Feb 23 22:02:41 poo ntpd[2294]: peers refreshed Feb 23 22:02:48 poo kernel: [ 678.963693] eth1: transmit timed out, tx_status 00 status 8601. Feb 23 22:02:48 poo kernel: [ 678.963713] diagnostics: net 0cd8 media 8880 dma 0000003a fifo 0000 Feb 23 22:02:48 poo kernel: [ 678.963722] eth1: Interrupt posted but not delivered -- IRQ blocked by another device? Feb 23 22:02:48 poo kernel: [ 678.963796] Flags; bus-master 1, dirty 16(0) current 16(0) Feb 23 22:02:48 poo kernel: [ 678.963803] Transmit list 00000000 vs. ffff880037000200. Feb 23 22:02:48 poo kernel: [ 678.963810] 0: @ffff880037000200 length 8000005a status 0001005a Feb 23 22:02:48 poo kernel: [ 678.963812] 1: @ffff880037000298 length 80000036 status 00010036 Feb 23 22:02:48 poo kernel: [ 678.963814] 2: @ffff880037000330 length 8000004e status 0001004e Feb 23 22:02:48 poo kernel: [ 678.963816] 3: @ffff8800370003c8 length 80000122 status 0c010122 Feb 23 22:02:48 poo kernel: [ 678.963818] 4: @ffff880037000460 length 800000c4 status 0c0100c4 Feb 23 22:02:48 poo kernel: [ 678.963820] 5: @ffff8800370004f8 length 80000122 status 0c010122 Feb 23 22:02:48 poo kernel: [ 678.963822] 6: @ffff880037000590 length 80000122 status 0c010122 Feb 23 22:02:48 poo kernel: [ 678.963824] 7: @ffff880037000628 length 8000010a status 0c01010a Feb 23 22:02:48 poo kernel: [ 678.963826] 8: @ffff8800370006c0 length 80000046 status 00010046 Feb 23 22:02:48 poo kernel: [ 678.963828] 9: @ffff880037000758 length 8000006e status 0001006e Feb 23 22:02:48 poo kernel: [ 678.963830] 10: @ffff8800370007f0 length 80000172 status 00010172 Feb 23 22:02:48 poo kernel: [ 678.963832] 11: @ffff880037000888 length 800000bd status 0c0100bd Feb 23 22:02:48 poo kernel: [ 678.963834] 12: @ffff880037000920 length 800000d8 status 000100d8 Feb 23 22:02:48 poo kernel: [ 678.963836] 13: @ffff8800370009b8 length 8000011a status 0c01011a Feb 23 22:02:48 poo kernel: [ 678.963837] 14: @ffff880037000a50 length 80000172 status 80010172 Feb 23 22:02:48 poo kernel: [ 678.963839] 15: @ffff880037000ae8 length 800000bd status 8c0100bd Feb 23 22:02:51 poo dnsmasq-dhcp[3574]: DHCPDISCOVER(eth1) 10.0.0.1 00:1c:23:a2:e7:c3 Feb 23 22:02:51 poo dnsmasq-dhcp[3574]: DHCPOFFER(eth1) 192.168.1.141 00:1c:23:a2:e7:c3 Feb 23 22:02:53 poo kernel: [ 683.964682] eth1: transmit timed out, tx_status 00 status 8201. Feb 23 22:02:53 poo kernel: [ 683.964700] diagnostics: net 0cd8 media 8880 dma 00000032 fifo 0000 Feb 23 22:02:53 poo kernel: [ 683.964709] eth1: Interrupt posted but not delivered -- IRQ blocked by another device? Feb 23 22:02:53 poo kernel: [ 683.964777] Flags; bus-master 1, dirty 32(0) current 32(0) Feb 23 22:02:53 poo kernel: [ 683.964783] Transmit list 00000000 vs. ffff880037000200. Feb 23 22:02:53 poo kernel: [ 683.964790] 0: @ffff880037000200 length 80000058 status 0c010058 Feb 23 22:02:53 poo kernel: [ 683.964792] 1: @ffff880037000298 length 80000172 status 00010172 Feb 23 22:02:53 poo kernel: [ 683.964794] 2: @ffff880037000330 length 800000bd status 0c0100bd Feb 23 22:02:53 poo kernel: [ 683.964796] 3: @ffff8800370003c8 length 8000015a status 0001015a Feb 23 22:02:53 poo kernel: [ 683.964797] 4: @ffff880037000460 length 800000b1 status 0c0100b1 Feb 23 22:02:53 poo kernel: [ 683.964799] 5: @ffff8800370004f8 length 8000010a status 0c01010a Feb 23 22:02:53 poo kernel: [ 683.964801] 6: @ffff880037000590 length 8000013a status 0001013a Feb 23 22:02:53 poo kernel: [ 683.964803] 7: @ffff880037000628 length 8000015a status 0001015a Feb 23 22:02:53 poo kernel: [ 683.964805] 8: @ffff8800370006c0 length 800000b1 status 0c0100b1 Feb 23 22:02:53 poo kernel: [ 683.964807] 9: @ffff880037000758 length 80000036 status 00010036 Feb 23 22:02:53 poo kernel: [ 683.964809] 10: @ffff8800370007f0 length 8000005a status 0001005a Feb 23 22:02:53 poo kernel: [ 683.964811] 11: @ffff880037000888 length 8000011a status 0c01011a Feb 23 22:02:53 poo kernel: [ 683.964813] 12: @ffff880037000920 length 80000126 status 0c010126 Feb 23 22:02:53 poo kernel: [ 683.964815] 13: @ffff8800370009b8 length 8000013a status 0001013a Feb 23 22:02:53 poo kernel: [ 683.964817] 14: @ffff880037000a50 length 80000046 status 80010046 Feb 23 22:02:53 poo kernel: [ 683.964819] 15: @ffff880037000ae8 length 8000015a status 8001015a ...and this into /var/log/messages: Feb 23 21:58:01 poo kernel: [ 391.545008] eth1: setting full-duplex. Feb 23 21:58:01 poo kernel: [ 391.545033] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready Feb 23 21:58:10 poo kernel: [ 401.322302] ------------[ cut here ]------------ Feb 23 21:58:10 poo kernel: [ 401.322314] WARNING: at net/sched/sch_generic.c:254 dev_watchdog+0xe3/0x153() Feb 23 21:58:10 poo kernel: [ 401.322316] Hardware name: Feb 23 21:58:10 poo kernel: [ 401.322318] NETDEV WATCHDOG: eth1 (3c59x): transmit queue 0 timed out Feb 23 21:58:10 poo kernel: [ 401.322320] Modules linked in: xt_state iptable_filter ipt_MASQUERADE iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack ip_tables x_tables binfmt_misc nfsd auth_rpcgss nfs_acl nfs lockd fscache sunrpc loop snd_hda_codec_realtek hid_generic usbhid hid snd_hda_intel snd_hda_codec coretemp kvm_intel snd_hwdep kvm i915 snd_pcm snd_page_alloc crc32c_intel drm_kms_helper drm snd_seq ghash_clmulni_intel snd_seq_device cryptd snd_timer iTCO_wdt psmouse snd iTCO_vendor_support i2c_i801 microcode acpi_cpufreq mperf processor lpc_ich pcspkr serio_raw mfd_core evdev soundcore i2c_algo_bit i2c_core mei ehci_pci button video ehci_hcd ext4 crc16 jbd2 mbcache sg sr_mod cdrom sd_mod crc_t10dif ata_generic 3c59x mii fan thermal thermal_sys xhci_hcd usbcore usb_common ata_piix libata scsi_mod e1000e Feb 23 21:58:10 poo kernel: [ 401.322385] Pid: 0, comm: swapper/2 Not tainted 3.8.0 #1 Feb 23 21:58:10 poo kernel: [ 401.322387] Call Trace: Feb 23 21:58:10 poo kernel: [ 401.322389] <IRQ> [<ffffffff8103ccf0>] ? warn_slowpath_common+0x76/0x8a Feb 23 21:58:10 poo kernel: [ 401.322399] [<ffffffff812e10d9>] ? netif_tx_lock+0x7a/0x7a Feb 23 21:58:10 poo kernel: [ 401.322402] [<ffffffff8103cd9c>] ? warn_slowpath_fmt+0x45/0x4a Feb 23 21:58:10 poo kernel: [ 401.322406] [<ffffffff812e10c6>] ? netif_tx_lock+0x67/0x7a Feb 23 21:58:10 poo kernel: [ 401.322412] [<ffffffff812e11bc>] ? dev_watchdog+0xe3/0x153 Feb 23 21:58:10 poo kernel: [ 401.322416] [<ffffffff81047efc>] ? call_timer_fn+0x34/0xf6 Feb 23 21:58:10 poo kernel: [ 401.322420] [<ffffffff812e10d9>] ? netif_tx_lock+0x7a/0x7a Feb 23 21:58:10 poo kernel: [ 401.322424] [<ffffffff81049426>] ? run_timer_softirq+0x18d/0x1d6 Feb 23 21:58:10 poo kernel: [ 401.322429] [<ffffffff811c3099>] ? timerqueue_add+0x79/0x98 Feb 23 21:58:10 poo kernel: [ 401.322432] [<ffffffff81043396>] ? __do_softirq+0xac/0x1d1 Feb 23 21:58:10 poo kernel: [ 401.322436] [<ffffffff81074d18>] ? ktime_get+0x62/0x6a Feb 23 21:58:10 poo kernel: [ 401.322442] [<ffffffff810285f9>] ? paravirt_write_msr+0xb/0xe Feb 23 21:58:10 poo kernel: [ 401.322446] [<ffffffff81079537>] ? clockevents_program_event+0x9a/0xb6 Feb 23 21:58:10 poo kernel: [ 401.322451] [<ffffffff8138cbdc>] ? call_softirq+0x1c/0x30 Feb 23 21:58:10 poo kernel: [ 401.322454] [<ffffffff8100f9ce>] ? do_softirq+0x3a/0x78 Feb 23 21:58:10 poo kernel: [ 401.322457] [<ffffffff81043581>] ? irq_exit+0x3a/0x91 Feb 23 21:58:10 poo kernel: [ 401.322462] [<ffffffff81028a74>] ? smp_apic_timer_interrupt+0x73/0x81 Feb 23 21:58:10 poo kernel: [ 401.322465] [<ffffffff8138c49d>] ? apic_timer_interrupt+0x6d/0x80 Feb 23 21:58:10 poo kernel: [ 401.322466] <EOI> [<ffffffff81079537>] ? clockevents_program_event+0x9a/0xb6 Feb 23 21:58:10 poo kernel: [ 401.322474] [<ffffffff812a537f>] ? arch_local_irq_enable+0x7/0x8 Feb 23 21:58:10 poo kernel: [ 401.322477] [<ffffffff812a5aad>] ? cpuidle_wrap_enter+0x3c/0x71 Feb 23 21:58:10 poo kernel: [ 401.322480] [<ffffffff812a5732>] ? cpuidle_enter_state+0xa/0x31 Feb 23 21:58:10 poo kernel: [ 401.322483] [<ffffffff812a5848>] ? cpuidle_idle_call+0xef/0x1a6 Feb 23 21:58:10 poo kernel: [ 401.322488] [<ffffffff81014dfd>] ? cpu_idle+0x9c/0xe6 Feb 23 21:58:10 poo kernel: [ 401.322492] [<ffffffff81378b1b>] ? start_secondary+0x1e0/0x1e6 Feb 23 21:58:10 poo kernel: [ 401.322495] ---[ end trace 07876c6d48c7014f ]--- Feb 23 22:02:39 poo kernel: [ 669.071740] eth1: setting full-duplex. At this point as far as debian is concerned the device works. In reality it does not work at all. No packets are being transmitted or received. After a few minutes of running with the device brought up the output of /proc/interrupts shows: CPU0 CPU1 CPU2 CPU3 18: 0 0 0 0 IO-APIC-fasteoi eth1 (the PCI card) 40: 7154 721 4809 742 PCI-MSI-edge eth0 (the integrated eth controller of the mobo) The attached 'lspci' logs also show the 3Com card had IRQ18 assigned to it. NOTE: so did the motherboard's SMBus Controller (00:1f:3). Note 1: A side-effect of bringing the iface up is that my USB keyboard slows down considerably (as if the rate at which it reads keypresses would go down to ~10 presses per second). Note 2: I am currently running kernel 3.8, because the stock debian 3.2 kernel freezes the computer after what appears to be a random time (unrelated to what I actually do on the system, if doing anything at all). However the bug I am reporting here applies exactly in the same manner to both 3.2 and 3.8 kernels. Note 3: I tried booting both kernels with the 'pci=nomsi' parameter, but that didn't change anything. Note 4: This is likely not a HW issue, since I tested the configuration in windoze, and all was working as expected. Thank you for your help, -szabolcs -- Package-specific info: ** Kernel log: boot messages should be attached ** Model information sys_vendor: product_name: product_version: chassis_vendor: chassis_version: bios_vendor: Intel Corporation bios_version: SLZ7710H.86A.0095.2013.0117.1516 board_vendor: Intel Corporation board_name: DZ77SL-50K board_version: AAG55115-300 ** PCI devices: 00:00.0 Host bridge [0600]: Intel Corporation Xeon E3-1200 v2/3rd Gen Core processor DRAM Controller [8086:0150] (rev 09) Subsystem: Intel Corporation Device [8086:2030] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> 00:02.0 VGA compatible controller [0300]: Intel Corporation Xeon E3-1200 v2/3rd Gen Core processor Graphics Controller [8086:0152] (rev 09) (prog-if 00 [VGA controller]) Subsystem: Intel Corporation Device [8086:2030] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 43 Region 0: Memory at f7800000 (64-bit, non-prefetchable) [size=4M] Region 2: Memory at e0000000 (64-bit, prefetchable) [size=256M] Region 4: I/O ports at f000 [size=64] Expansion ROM at <unassigned> [disabled] Capabilities: <access denied> Kernel driver in use: i915 00:14.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB xHCI Host Controller [8086:1e31] (rev 04) (prog-if 30 [XHCI]) Subsystem: Intel Corporation Device [8086:2030] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 41 Region 0: Memory at f7d20000 (64-bit, non-prefetchable) [size=64K] Capabilities: <access denied> Kernel driver in use: xhci_hcd 00:16.0 Communication controller [0780]: Intel Corporation 7 Series/C210 Series Chipset Family MEI Controller #1 [8086:1e3a] (rev 04) Subsystem: Intel Corporation Device [8086:2030] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 42 Region 0: Memory at f7d3a000 (64-bit, non-prefetchable) [size=16] Capabilities: <access denied> Kernel driver in use: mei 00:19.0 Ethernet controller [0200]: Intel Corporation 82579V Gigabit Network Connection [8086:1503] (rev 04) Subsystem: Intel Corporation Device [8086:2030] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 40 Region 0: Memory at f7d00000 (32-bit, non-prefetchable) [size=128K] Region 1: Memory at f7d38000 (32-bit, non-prefetchable) [size=4K] Region 2: I/O ports at f060 [size=32] Capabilities: <access denied> Kernel driver in use: e1000e 00:1a.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #2 [8086:1e2d] (rev 04) (prog-if 20 [EHCI]) Subsystem: Intel Corporation Device [8086:2030] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at f7d37000 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci-pci 00:1b.0 Audio device [0403]: Intel Corporation 7 Series/C210 Series Chipset Family High Definition Audio Controller [8086:1e20] (rev 04) Subsystem: Intel Corporation Device [8086:2030] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 44 Region 0: Memory at f7d30000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel 00:1c.0 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 1 [8086:1e10] (rev c4) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:1c.7 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 8 [8086:1e1e] (rev c4) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=02, subordinate=03, sec-latency=0 I/O behind bridge: 0000e000-0000efff Memory behind bridge: f7c00000-f7cfffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:1d.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #1 [8086:1e26] (rev 04) (prog-if 20 [EHCI]) Subsystem: Intel Corporation Device [8086:2030] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 23 Region 0: Memory at f7d36000 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci-pci 00:1f.0 ISA bridge [0601]: Intel Corporation Z77 Express Chipset LPC Controller [8086:1e44] (rev 04) Subsystem: Intel Corporation Device [8086:2030] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> Kernel driver in use: lpc_ich 00:1f.2 IDE interface [0101]: Intel Corporation 7 Series/C210 Series Chipset Family 4-port SATA Controller [IDE mode] [8086:1e00] (rev 04) (prog-if 8f [Master SecP SecO PriP PriO]) Subsystem: Intel Corporation Device [8086:2030] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 19 Region 0: I/O ports at f130 [size=8] Region 1: I/O ports at f120 [size=4] Region 2: I/O ports at f110 [size=8] Region 3: I/O ports at f100 [size=4] Region 4: I/O ports at f0f0 [size=16] Region 5: I/O ports at f0e0 [size=16] Capabilities: <access denied> Kernel driver in use: ata_piix 00:1f.3 SMBus [0c05]: Intel Corporation 7 Series/C210 Series Chipset Family SMBus Controller [8086:1e22] (rev 04) Subsystem: Intel Corporation Device [8086:2030] Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin C routed to IRQ 18 Region 0: Memory at f7d35000 (64-bit, non-prefetchable) [size=256] Region 4: I/O ports at f040 [size=32] 00:1f.5 IDE interface [0101]: Intel Corporation 7 Series/C210 Series Chipset Family 2-port SATA Controller [IDE mode] [8086:1e08] (rev 04) (prog-if 85 [Master SecO PriO]) Subsystem: Intel Corporation Device [8086:2030] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 19 Region 0: I/O ports at f0d0 [size=8] Region 1: I/O ports at f0c0 [size=4] Region 2: I/O ports at f0b0 [size=8] Region 3: I/O ports at f0a0 [size=4] Region 4: I/O ports at f090 [size=16] Region 5: I/O ports at f080 [size=16] Capabilities: <access denied> Kernel driver in use: ata_piix 02:00.0 PCI bridge [0604]: Integrated Technology Express, Inc. Device [1283:8892] (rev 30) (prog-if 01 [Subtractive decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=02, secondary=03, subordinate=03, sec-latency=64 I/O behind bridge: 0000e000-0000efff Memory behind bridge: f7c00000-f7cfffff Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> 03:02.0 Ethernet controller [0200]: 3Com Corporation 3c905B 100BaseTX [Cyclone] [10b7:9055] (rev 30) Subsystem: 3Com Corporation 3C905B Fast Etherlink XL 10/100 [10b7:9055] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 (2500ns min, 2500ns max), Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 18 Region 0: I/O ports at e000 [size=128] Region 1: Memory at f7c20000 (32-bit, non-prefetchable) [size=128] Expansion ROM at f7c00000 [disabled] [size=128K] Capabilities: <access denied> Kernel driver in use: 3c59x ** USB devices: Bus 003 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 004 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 003: ID 04b3:3103 IBM Corp. ScrollPoint Pro Mouse Bus 003 Device 004: ID 04f2:0116 Chicony Electronics Co., Ltd KU-2971/KU-0325 Keyboard -- System Information: Debian Release: 7.0 APT prefers testing APT policy: (500, 'testing') Architecture: amd64 (x86_64) Foreign Architectures: i386 Kernel: Linux 3.8.0 (SMP w/4 CPU cores) Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8) Shell: /bin/sh linked to /bin/dash Versions of packages linux-image-3.2.0-4-amd64 depends on: ii debconf [debconf-2.0] 1.5.49 ii initramfs-tools [linux-initramfs-tool] 0.109 ii kmod 9-2 ii linux-base 3.5 ii module-init-tools 9-2 Versions of packages linux-image-3.2.0-4-amd64 recommends: ii firmware-linux-free 3.2 Versions of packages linux-image-3.2.0-4-amd64 suggests: pn debian-kernel-handbook <none> ii grub-pc 1.99-26 pn linux-doc-3.2 <none> Versions of packages linux-image-3.2.0-4-amd64 is related to: pn firmware-atheros <none> pn firmware-bnx2 <none> pn firmware-bnx2x <none> pn firmware-brcm80211 <none> pn firmware-intelwimax <none> pn firmware-ipw2x00 <none> pn firmware-ivtv <none> pn firmware-iwlwifi <none> pn firmware-libertas <none> pn firmware-linux <none> pn firmware-linux-nonfree <none> pn firmware-myricom <none> pn firmware-netxen <none> pn firmware-qlogic <none> pn firmware-ralink <none> pn firmware-realtek <none> pn xen-hypervisor <none> -- debconf information excluded
--- End Message ---
--- Begin Message ---Hi This bug was filed for a very old kernel or the bug is old itself without resolution. If you can reproduce it with - the current version in unstable/testing - the latest kernel from backports please reopen the bug, see https://www.debian.org/Bugs/server-control for details. Regards, Salvatore
--- End Message ---
