Package: linux-2.6 Version: 2.6.32-34squeeze1 Severity: normal
The card is identified correctly, but never manages to associate with an AP. The card is a generic rtl8185 cannibalised out of a Maplin HTC PC bundle. Dmesg self-explanatory. Unfortunately the web site on sourceforge seems a bit blank so I cannot pick up a more recent driver to test build to see if this can be fixed. -- Package-specific info: ** Version: Linux version 2.6.32-5-686 (Debian 2.6.32-34squeeze1) ([email protected]) (gcc version 4.3.5 (Debian 4.3.5-4) ) #1 SMP Wed May 18 07:08:50 UTC 2011 ** Command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32-5-686 root=UUID=ddf5a907-47ff-4167-adc8-f00fd59ed1f8 ro acpi_enforce_resources=lax quiet ** Not tainted ** Kernel log: [ 2.646116] uhci_hcd 0000:00:10.3: PCI INT B -> Link[ALKB] -> GSI 21 (level, low) -> IRQ 21 [ 2.646134] uhci_hcd 0000:00:10.3: setting latency timer to 64 [ 2.646141] uhci_hcd 0000:00:10.3: UHCI Host Controller [ 2.646160] uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5 [ 2.646199] uhci_hcd 0000:00:10.3: irq 21, io base 0x0000f400 [ 2.646281] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001 [ 2.646289] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.646295] usb usb5: Product: UHCI Host Controller [ 2.646300] usb usb5: Manufacturer: Linux 2.6.32-5-686 uhci_hcd [ 2.646306] usb usb5: SerialNumber: 0000:00:10.3 [ 2.646640] usb usb5: configuration #1 chosen from 1 choice [ 2.647236] hub 5-0:1.0: USB hub found [ 2.647276] hub 5-0:1.0: 2 ports detected [ 2.824026] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 2.988236] ata2.00: ATA-7: Maxtor 6Y080M0, YAR511W0, max UDMA/100 [ 2.988245] ata2.00: 156301488 sectors, multi 16: LBA48 [ 3.004253] ata2.00: configured for UDMA/100 [ 3.004477] scsi 1:0:0:0: Direct-Access ATA Maxtor 6Y080M0 YAR5 PQ: 0 ANSI: 5 [ 3.303701] sd 1:0:0:0: [sda] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB) [ 3.303789] sd 1:0:0:0: [sda] Write Protect is off [ 3.303796] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 3.303832] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 3.304151] sda: sda1 sda2 [ 3.326469] sd 1:0:0:0: [sda] Attached SCSI disk [ 3.599716] PM: Starting manual resume from disk [ 3.599727] PM: Resume from partition 8:1 [ 3.599732] PM: Checking hibernation image. [ 3.600083] PM: Error -22 checking image file [ 3.600087] PM: Resume from disk failed. [ 3.674961] kjournald starting. Commit interval 5 seconds [ 3.674984] EXT3-fs: mounted filesystem with ordered data mode. [ 5.254134] udev[309]: starting version 164 [ 5.907667] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 5.936574] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0 [ 5.936593] ACPI: Power Button [PWRB] [ 5.936735] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input1 [ 5.936752] ACPI: Sleep Button [SLPB] [ 5.936915] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2 [ 5.936925] ACPI: Power Button [PWRF] [ 6.076088] processor LNXCPU:00: registered as cooling_device0 [ 6.113043] input: PC Speaker as /devices/platform/pcspkr/input/input3 [ 6.197120] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 6.261327] parport_pc 00:0a: reported by Plug and Play ACPI [ 6.261383] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE] [ 6.458051] cfg80211: Using static regulatory domain info [ 6.458058] cfg80211: Regulatory domain: US [ 6.458064] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 6.458072] (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm) [ 6.458079] (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 6.458087] (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 6.458095] (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 6.458102] (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 6.458110] (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm) [ 6.459361] cfg80211: Calling CRDA for country: US [ 7.418256] rtl8180 0000:00:08.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 7.659638] phy0: Selected rate control algorithm 'minstrel' [ 7.661526] phy0: hwaddr 00:e0:46:50:00:40, RTL8185vD + rtl8225z2 [ 8.002042] ACPI: PCI Interrupt Link [ALKC] enabled at IRQ 22 [ 8.002065] VIA 82xx Audio 0000:00:11.5: PCI INT C -> Link[ALKC] -> GSI 22 (level, low) -> IRQ 22 [ 8.002248] VIA 82xx Audio 0000:00:11.5: setting latency timer to 64 [ 9.498139] Adding 1959888k swap on /dev/sda1. Priority:-1 extents:1 across:1959888k [ 9.763059] EXT3 FS on sda2, internal journal [ 9.974774] loop: module loaded [ 10.124184] it87: Found IT8716F chip at 0x290, revision 1 [ 10.124196] it87: in3 is VCC (+5V) [ 10.124200] it87: in7 is VCCH (+5V Stand-By) [ 10.124284] ACPI: I/O resource it87 [0x295-0x296] conflicts with ACPI region IP__ [0x295-0x296] [ 10.124290] ACPI: This conflict may cause random problems and system instability [ 10.124295] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver [ 10.125721] it87 it87.656: Detected broken BIOS defaults, disabling PWM interface [ 10.190543] 802.1Q VLAN Support v1.8 Ben Greear <[email protected]> [ 10.190552] All bugs added by David S. Miller <[email protected]> [ 11.046888] tun: Universal TUN/TAP device driver, 1.6 [ 11.046897] tun: (C) 1999-2004 Max Krasnyansky <[email protected]> [ 11.155830] ADDRCONF(NETDEV_UP): eth2: link is not ready [ 11.156449] e1000: eth2 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX [ 11.157179] ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready [ 11.586395] RPC: Registered udp transport module. [ 11.586402] RPC: Registered tcp transport module. [ 11.586407] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 11.907910] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 11.908402] e1000: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX [ 11.909103] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 11.920095] Slow work thread pool: Starting up [ 11.921507] Slow work thread pool: Ready [ 11.923832] FS-Cache: Loaded [ 12.031425] FS-Cache: Netfs 'nfs' registered for caching [ 12.104331] Installing knfsd (copyright (C) 1996 [email protected]). [ 12.471713] fuse init (API version 7.13) [ 13.999504] svc: failed to register lockdv1 RPC service (errno 97). [ 14.002467] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory [ 14.020239] NFSD: starting 90-second grace period [ 21.440013] tap0: no IPv6 routers present [ 21.504018] eth2: no IPv6 routers present [ 22.636012] eth0: no IPv6 routers present [ 662.952668] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 664.112034] wlan0: direct probe to AP 00:90:4c:91:00:03 (try 1) [ 664.312026] wlan0: direct probe to AP 00:90:4c:91:00:03 (try 2) [ 664.512019] wlan0: direct probe to AP 00:90:4c:91:00:03 (try 3) [ 664.712014] wlan0: direct probe to AP 00:90:4c:91:00:03 timed out ** Model information not available ** Loaded modules: Module Size Used by fuse 44052 1 nfsd 193055 13 exportfs 2586 1 nfsd nfs 206510 0 lockd 49301 2 nfsd,nfs fscache 24422 1 nfs nfs_acl 1695 2 nfsd,nfs auth_rpcgss 25200 2 nfsd,nfs sunrpc 134340 12 nfsd,nfs,lockd,nfs_acl,auth_rpcgss tun 8740 2 8021q 13950 0 garp 4066 1 8021q stp 996 1 garp it87 11487 0 hwmon_vid 1528 1 it87 loop 9729 0 snd_via82xx 15256 0 gameport 6025 1 snd_via82xx snd_ac97_codec 79148 1 snd_via82xx ac97_bus 710 1 snd_ac97_codec snd_pcm_oss 28671 0 snd_mixer_oss 10461 1 snd_pcm_oss snd_pcm 47226 3 snd_via82xx,snd_ac97_codec,snd_pcm_oss arc4 974 2 snd_page_alloc 4977 2 snd_via82xx,snd_pcm snd_mpu401_uart 4067 1 snd_via82xx ecb 1405 2 snd_seq_midi 3576 0 snd_rawmidi 12513 2 snd_mpu401_uart,snd_seq_midi rtl8180 22783 0 snd_seq_midi_event 3684 1 snd_seq_midi snd_seq 35327 2 snd_seq_midi,snd_seq_midi_event mac80211 122866 1 rtl8180 snd_timer 12258 2 snd_pcm,snd_seq eeprom_93cx6 963 1 rtl8180 snd_seq_device 3673 3 snd_seq_midi,snd_rawmidi,snd_seq snd 34387 10 snd_via82xx,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_mpu401_uart,snd_rawmidi,snd_seq,snd_timer,snd_seq_device i2c_viapro 4419 0 cfg80211 86977 2 rtl8180,mac80211 parport_pc 15799 0 psmouse 44777 0 evdev 5609 6 shpchp 21220 0 i2c_core 12751 1 i2c_viapro parport 22554 1 parport_pc pcspkr 1207 0 rfkill 10196 1 cfg80211 processor 26259 0 soundcore 3450 1 snd serio_raw 2916 0 button 3598 0 pci_hotplug 18065 1 shpchp ext3 93944 1 jbd 31965 1 ext3 mbcache 3762 1 ext3 sd_mod 25937 3 crc_t10dif 1012 1 sd_mod ata_generic 2067 0 uhci_hcd 15989 0 pata_via 5669 0 sata_via 5576 2 via_rhine 14527 0 libata 115513 3 ata_generic,pata_via,sata_via thermal 9206 0 ehci_hcd 28453 0 floppy 40923 0 mii 2714 1 via_rhine scsi_mod 104613 2 sd_mod,libata thermal_sys 9378 2 processor,thermal usbcore 98541 3 uhci_hcd,ehci_hcd nls_base 4541 1 usbcore e1000 77145 0 ** Network interface configuration: # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface allow-hotplug eth0 iface eth0 inet dhcp auto tap0 iface tap0 inet static address 192.168.250.254 netmask 255.255.255.0 tunctl_user uml-net auto eth2 iface eth2 inet static address 192.168.249.254 netmask 255.255.255.0 ** Network status: *** IP interfaces and addresses: 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 100 link/ether 00:11:0a:5c:7e:56 brd ff:ff:ff:ff:ff:ff inet 192.168.3.57/24 brd 192.168.3.255 scope global eth0 inet6 fe80::211:aff:fe5c:7e56/64 scope link valid_lft forever preferred_lft forever 3: eth1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000 link/ether 00:1b:b9:91:7b:63 brd ff:ff:ff:ff:ff:ff 4: eth2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 100 link/ether 00:11:0a:5c:7e:57 brd ff:ff:ff:ff:ff:ff inet 192.168.249.254/24 brd 192.168.249.255 scope global eth2 inet6 fe80::211:aff:fe5c:7e57/64 scope link valid_lft forever preferred_lft forever 5: wlan0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN qlen 1000 link/ether 00:e0:46:50:00:40 brd ff:ff:ff:ff:ff:ff 6: tap0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UNKNOWN qlen 500 link/ether 22:24:61:af:71:6a brd ff:ff:ff:ff:ff:ff inet 192.168.250.254/24 brd 192.168.250.255 scope global tap0 inet6 fe80::2024:61ff:feaf:716a/64 scope link valid_lft forever preferred_lft forever *** Device statistics: Inter-| Receive | Transmit face |bytes packets errs drop fifo frame compressed multicast|bytes packets errs drop fifo colls carrier compressed lo: 8756 104 0 0 0 0 0 0 8756 104 0 0 0 0 0 0 eth0: 344161 1805 0 0 0 0 0 0 234296 1032 0 0 0 0 0 0 eth1: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 eth2: 4832 36 0 0 0 0 0 0 4860 42 0 0 0 0 0 0 wlan0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 tap0: 0 0 0 0 0 0 0 0 230 3 0 3 0 0 0 0 *** Protocol statistics: Ip: 1811 total packets received 0 forwarded 0 incoming packets discarded 1809 incoming packets delivered 1143 requests sent out Icmp: 0 ICMP messages received 0 input ICMP message failed. ICMP input histogram: 0 ICMP messages sent 0 ICMP messages failed ICMP output histogram: Tcp: 5 active connections openings 4 passive connection openings 0 failed connection attempts 0 connection resets received 2 connections established 1563 segments received 982 segments send out 0 segments retransmited 0 bad segments received. 0 resets sent Udp: 170 packets received 0 packets to unknown port received. 0 packet receive errors 161 packets sent UdpLite: TcpExt: 3 TCP sockets finished time wait in fast timer 9 delayed acks sent 6 packets directly queued to recvmsg prequeue. 419 packet headers predicted 63 acknowledgments not containing data payload received 730 predicted acknowledgments IpExt: InNoRoutes: 2 InBcastPkts: 85 InOctets: 325811 OutOctets: 230648 InBcastOctets: 16350 *** Device features: eth0: 0x10b89 eth1: 0x0 eth2: 0x10b89 lo: 0x13865 tap0: 0x0 wlan0: 0x2000 ** PCI devices: 00:00.0 Host bridge [0600]: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host Bridge [1106:0314] Subsystem: Elitegroup Computer Systems Device [1019:aa51] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 8 Region 0: Memory at e8000000 (32-bit, prefetchable) [size=128M] Capabilities: [80] AGP version 3.5 Status: RQ=8 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8 Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none> Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: agpgart-via 00:00.1 Host bridge [0600]: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host Bridge [1106:1314] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 00:00.2 Host bridge [0600]: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host Bridge [1106:2314] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 00:00.3 Host bridge [0600]: VIA Technologies, Inc. PT890 Host Bridge [1106:3208] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 00:00.4 Host bridge [0600]: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host Bridge [1106:4314] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 00:00.7 Host bridge [0600]: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host Bridge [1106:7314] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 00:01.0 PCI bridge [0604]: VIA Technologies, Inc. VT8237/VX700 PCI Bridge [1106:b198] (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: fb000000-fcffffff Prefetchable memory behind bridge: f4000000-f7ffffff Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR+ <PERR+ BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [70] Power Management version 2 Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- 00:08.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8185 IEEE 802.11a/b/g Wireless LAN Controller [10ec:8185] (rev 20) Subsystem: Realtek Semiconductor Co., Ltd. RTL-8185 IEEE 802.11a/b/g Wireless LAN Controller [10ec:8185] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 (8000ns min, 16000ns max), Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at f000 [size=256] Region 1: Memory at fdfff000 (32-bit, non-prefetchable) [size=512] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: rtl8180 00:09.0 Ethernet controller [0200]: Intel Corporation 82546EB Gigabit Ethernet Controller (Copper) [8086:1010] (rev 01) Subsystem: Compaq Computer Corporation NC7170 Gigabit Server Adapter [0e11:00db] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 252 (63750ns min), Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 17 Region 0: Memory at fdfc0000 (64-bit, non-prefetchable) [size=128K] Region 2: Memory at fdf40000 (64-bit, non-prefetchable) [size=256K] Region 4: I/O ports at ff00 [size=64] [virtual] Expansion ROM at 3c000000 [disabled] [size=256K] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME- Capabilities: [e4] PCI-X non-bridge device Command: DPERE- ERO+ RBC=512 OST=1 Status: Dev=00:00.0 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=2048 DMOST=1 DMCRS=16 RSCEM- 266MHz- 533MHz- Capabilities: [f0] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Kernel driver in use: e1000 00:09.1 Ethernet controller [0200]: Intel Corporation 82546EB Gigabit Ethernet Controller (Copper) [8086:1010] (rev 01) Subsystem: Compaq Computer Corporation NC7170 Gigabit Server Adapter [0e11:00db] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 252 (63750ns min), Cache Line Size: 64 bytes Interrupt: pin B routed to IRQ 18 Region 0: Memory at fdfa0000 (64-bit, non-prefetchable) [size=128K] Region 4: I/O ports at fe00 [size=64] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME- Capabilities: [e4] PCI-X non-bridge device Command: DPERE- ERO+ RBC=512 OST=1 Status: Dev=00:00.1 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=2048 DMOST=1 DMCRS=16 RSCEM- 266MHz- 533MHz- Capabilities: [f0] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Kernel driver in use: e1000 00:0f.0 IDE interface [0101]: VIA Technologies, Inc. VIA VT6420 SATA RAID Controller [1106:3149] (rev 80) (prog-if 8f [Master SecP SecO PriP PriO]) Subsystem: Elitegroup Computer Systems Device [1019:aa51] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 Interrupt: pin B routed to IRQ 20 Region 0: I/O ports at fd00 [size=8] Region 1: I/O ports at fc00 [size=4] Region 2: I/O ports at fb00 [size=8] Region 3: I/O ports at fa00 [size=4] Region 4: I/O ports at f900 [size=16] Region 5: I/O ports at f200 [size=256] Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: sata_via 00:0f.1 IDE interface [0101]: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE [1106:0571] (rev 06) (prog-if 8a [Master SecP PriP]) Subsystem: Elitegroup Computer Systems Device [1019:aa51] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 Interrupt: pin A routed to IRQ 20 Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8] Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1] Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8] Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1] Region 4: I/O ports at f800 [size=16] Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: pata_via 00:10.0 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 81) (prog-if 00 [UHCI]) Subsystem: Elitegroup Computer Systems Device [1019:aa51] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 21 Region 4: I/O ports at f700 [size=32] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: uhci_hcd 00:10.1 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 81) (prog-if 00 [UHCI]) Subsystem: Elitegroup Computer Systems Device [1019:aa51] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 21 Region 4: I/O ports at f600 [size=32] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: uhci_hcd 00:10.2 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 81) (prog-if 00 [UHCI]) Subsystem: Elitegroup Computer Systems Device [1019:aa51] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin B routed to IRQ 21 Region 4: I/O ports at f500 [size=32] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: uhci_hcd 00:10.3 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 81) (prog-if 00 [UHCI]) Subsystem: Elitegroup Computer Systems Device [1019:aa51] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin B routed to IRQ 21 Region 4: I/O ports at f400 [size=32] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: uhci_hcd 00:10.4 USB Controller [0c03]: VIA Technologies, Inc. USB 2.0 [1106:3104] (rev 86) (prog-if 20 [EHCI]) Subsystem: Elitegroup Computer Systems Device [1019:aa51] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin C routed to IRQ 21 Region 0: Memory at fdffe000 (32-bit, non-prefetchable) [size=256] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: ehci_hcd 00:11.0 ISA bridge [0601]: VIA Technologies, Inc. VT8237 ISA bridge [KT600/K8T800/K8T890 South] [1106:3227] Subsystem: Elitegroup Computer Systems Device [1019:aa51] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- 00:11.5 Multimedia audio controller [0401]: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller [1106:3059] (rev 60) Subsystem: Elitegroup Computer Systems Device [1019:aa51] Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin C routed to IRQ 22 Region 0: I/O ports at ee00 [size=256] Capabilities: [c0] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: VIA 82xx Audio 00:12.0 Ethernet controller [0200]: VIA Technologies, Inc. VT6102 [Rhine-II] [1106:3065] (rev 78) Subsystem: Elitegroup Computer Systems Device [1019:0102] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 (750ns min, 2000ns max), Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 23 Region 0: I/O ports at ea00 [size=256] Region 1: Memory at fdffd000 (32-bit, non-prefetchable) [size=256] Capabilities: [40] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: via-rhine 01:00.0 VGA compatible controller [0300]: VIA Technologies, Inc. CN700/P4M800 Pro/P4M800 CE/VN800 [S3 UniChrome Pro] [1106:3344] (rev 01) (prog-if 00 [VGA controller]) Subsystem: Elitegroup Computer Systems Device [1019:aa51] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (500ns min) Interrupt: pin A routed to IRQ 10 Region 0: Memory at f4000000 (32-bit, prefetchable) [size=64M] Region 1: Memory at fb000000 (32-bit, non-prefetchable) [size=16M] [virtual] Expansion ROM at fc000000 [disabled] [size=64K] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [70] AGP version 3.0 Status: RQ=256 Iso- ArqSz=0 Cal=7 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3+ Rate=x4,x8 Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP- GART64- 64bit- FW- Rate=<none> ** USB devices: Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub -- System Information: Debian Release: 6.0.1 APT prefers stable-updates APT policy: (500, 'stable-updates'), (500, 'stable') Architecture: i386 (i686) Kernel: Linux 2.6.32-5-686 (SMP w/1 CPU core) Locale: LANG=en_GB.UTF-8, LC_CTYPE=en_GB.UTF-8 (charmap=UTF-8) Shell: /bin/sh linked to /bin/dash Versions of packages linux-image-2.6.32-5-686 depends on: ii debconf [debconf-2.0] 1.5.36.1 Debian configuration management sy ii initramfs-tools [linux 0.98.8 tools for generating an initramfs ii linux-base 2.6.32-34squeeze1 Linux image base package ii module-init-tools 3.12-1 tools for managing Linux kernel mo Versions of packages linux-image-2.6.32-5-686 recommends: pn firmware-linux-free <none> (no description available) ii libc6-i686 2.11.2-10 Embedded GNU C Library: Shared lib Versions of packages linux-image-2.6.32-5-686 suggests: pn grub | lilo <none> (no description available) pn linux-doc-2.6.32 <none> (no description available) Versions of packages linux-image-2.6.32-5-686 is related to: pn firmware-bnx2 <none> (no description available) pn firmware-bnx2x <none> (no description available) pn firmware-ipw2x00 <none> (no description available) pn firmware-ivtv <none> (no description available) pn firmware-iwlwifi <none> (no description available) pn firmware-linux <none> (no description available) pn firmware-linux-nonfree <none> (no description available) pn firmware-qlogic <none> (no description available) pn firmware-ralink <none> (no description available) pn xen-hypervisor <none> (no description available) -- debconf information excluded -- To UNSUBSCRIBE, email to [email protected] with a subject of "unsubscribe". Trouble? Contact [email protected] Archive: http://lists.debian.org/[email protected]
