On 27/05/04, Cedric Pradalier ([EMAIL PROTECTED]) wrote: > >> Second, the fan control chip may be initialized with too low > >thresholds> (on my G3, they are too high). > >> I have a kernel patch to access it and I need testers to make it > >> included in the kernel :o). So if you mind... have a look at > >> http://cedric.pradalier.free.fr/ibook2/index.html > >> and report ! > > > >Through lack of time I've avoided compiling myself and am lazily using > >the stock unstable kernel (2.6.6-powerpc #1 Thu May 13). I'll get > >around to compiling for myself in a bit, and let you know how I get on.
> I undestand that it is not practical to compile a kernel just to test a > module. So I just tried to make it available in a binary form. > > Can you try adding > > deb http://cedric.pradalier.free.fr/ibook2/ ./ > > in you /etc/apt/sources.list file ? > > You should be able to install a package adm103x-module-2.6.6-powerpc, > and eventually, after modprobing the therm_adm103x module, you can > install wmadm, a small dockable app to monitor your ibook temperature. > > When loading therm_adm103x, it should output default parameter of the > adm103x chip in syslog. Can you report them ? I wonder if this is a > constant value for any ibook ? Cedric. Hi. Thanks very much! I have installed the module and dock applet. Seems to be working -- although I'm worried about frying my laptop! How do I check the current speed setting of my processor? I've tried to throttle it down even under a/c because of the noise of the fan. I'll report back with syslog notices soon. Kind regards, Rory admstate presently shows: Register 0x3D : 0x30 Device ID : 0x30 Register 0x3E : 0x41 Company ID : 0x41 Register 0x3F : 0x83 Therm-to-Fan enable : 1 Revision number : 3 Register 0x00 : 0xFD Monitor : 1 !INT enable : 0 TACH/AIN : 1 PWM Inv : 1 Fan fault enable : 1 PWM Mode : Fastest Calculated Speed Control Mode : Automatic Register 0x01 : 0x7B PWM1 enable : 1 TACH1 enable : 0 Loc Temp enable : 1 Remote1 Temp enable : 1 SW Reset : 0 Register 0x02 : 0x00 Alarm1 speed : 0 Fan1 fault : 0 Remote1 temp high : 0 Remote1 temp low : 0 Remote1 temp therm : 0 Remote1 diode error : 0 Loc temp high : 0 Loc temp low : 0 Register 0x03 : 0x20 Loc therm : 0 !THERM : 0 Register 0x06 : 0x40 Remote1 temp resolution : 0.000000 Local temp resolution : 0.250000 Register 0x08 : 0x00 Fan1 speed : inf rpm Register 0x0A : 0x3A Local temp : 58 Register 0x0B : 0x36 Remote1 temp : 54 Register 0x0D : 0x04 Local temp offset : 4 Register 0x0E : 0x08 Remote1 temp offset : 8 Register 0x10 : 0xFF Fan1 Tach High limit : 255 -> 1.323529-0.661765 Register 0x14 : 0x3C Local temp high limit : 60 Register 0x15 : 0x00 Local temp low limit : 0 Register 0x16 : 0x4F Local temp therm limit : 79 Register 0x18 : 0x50 Remote1 temp high limit : 80 Register 0x19 : 0x00 Remote1 temp low limit : 0 Register 0x1A : 0x60 Remote1 temp therm limit : 96 Register 0x20 : 0x5A Fan1 Spin Up : 0.600000 s PWM Freqency : 31.250000 Hz Speed range : 1324 rpm Register 0x22 : 0x05 Fan1 min speed : 33 % Register 0x23 : 0x51 Fan spin-up disable : 0 Ramp rate : 4 ADC sample rate : 1.000000 Hz Fan1 filter enable : 1 Register 0x24 : 0x78 Local fan starting temp : 60 Local fan speeding range : 5 Register 0x25 : 0x99 Remote fan1 starting temp : 76 Remote fan1 speeding range: 10 -- Rory Campbell-Lange <[EMAIL PROTECTED]> <www.campbell-lange.net>
