Hi, I've just installed a debian 1.3, and booting with boot disk eth0 3c905 is not recognized. So installed with dselect 2.0.30 kernel image and i copie it onto the boot floppy. Nothing changed. The strange thing, is that i've already installe debian 1.3 on e pc with 3c905. this is the dmesg: ole (max 63) pcibios_init : BIOS32 Service Directory structure at 0x000fdb70 pcibios_init : BIOS32 Service Directory entry at 0xfdb80 pcibios_init : PCI BIOS revision 2.10 entry at 0xfdba1 Probing PCI hardware. Warning : Unknown PCI device (10b7:9050). Please read include/linux/pci.h Warning : Unknown PCI device (1000:f). Please read include/linux/pci.h Calibrating delay loop.. ok - 199.07 BogoMIPS Memory: 62736k/65536k available (1008k kernel code, 384k reserved, 1408k data) Swansea University Computer Society NET3.035 for Linux 2.0 NET3: Unix domain sockets 0.13 for Linux NET3.035. Swansea University Computer Society TCP/IP for NET3.034 IP Protocols: ICMP, UDP, TCP VFS: Diskquotas version dquot_5.6.0 initialized Checking 386/387 coupling... Ok, fpu using exception 16 error reporting. Checking 'hlt' instruction... Ok. Linux version 2.0.30 ([EMAIL PROTECTED]) (gcc version 2.7.2.2) #1 Sun Jun 1 09:14:11 EST 1997 Real Time Clock Driver v1.07 tpqic02: Runtime config, $Revision: 0.4.1.5 $, $Date: 1994/10/29 02:46:13 $ tpqic02: DMA buffers: 20 blocks, at address 0x24ea00 (0x24e914) Ramdisk driver initialized : 16 ramdisks of 4096K size loop: registered device at major 7 ide: i82371 PIIX (Triton) on PCI bus 0 function 57 ide0: BM-DMA at 0xffa0-0xffa7 hdb: FX810S, ATAPI CDROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Floppy drive(s): fd0 is 1.44M Started kswapd v 1.4.2.2 FDC 0 is a post-1991 82077 md driver 0.35 MAX_MD_DEV=4, MAX_REAL=8 ncr53c8xx : at PCI bus 0, device 11, function 0 ncr_attach: unit=0 chip=875 base=febeff00, io_port=ec00, irq=11 ncr53c875-0: using memory mapped IO at virtual address 0x4805f00 ncr53c875-0: initial value of SCNTL3 = 55, final = 35 ncr53c875-0: requesting shared irq 11 (dev_id=0x90068) ncr53c875-0: restart (scsi reset). Failed initialization of WD-7000 SCSI card! PPA: unable to initialise controller at 0x378, error 2 scsi0 : ncr53c8xx (rel 1.12d) scsi : 1 host. Vendor: IBM Model: DORS-32160W Rev: WA6A Type: Direct-Access ANSI SCSI revision: 02 Detected scsi disk sda at scsi0, channel 0, id 0, lun 0 Vendor: IBM Model: DORS-32160W Rev: WA0A Type: Direct-Access ANSI SCSI revision: 02 Detected scsi disk sdb at scsi0, channel 0, id 1, lun 0 Vendor: IBM Model: DORS-32160W Rev: WA6A Type: Direct-Access ANSI SCSI revision: 02 Detected scsi disk sdc at scsi0, channel 0, id 2, lun 0 Vendor: IBM Model: DORS-32160W Rev: WA0A Type: Direct-Access ANSI SCSI revision: 02 Detected scsi disk sdd at scsi0, channel 0, id 3, lun 0 scsi : detected 4 SCSI disks total. ncr53c875-0-<target 0, lun 0>: WIDE SCSI (16 bit) enabled. ncr53c875-0-<target 0, lun 0>: FAST SCSI-2 100ns (20 Mb/sec) offset 8. SCSI device sda: hdwr sector= 512 bytes. Sectors= 4226725 [2063 MB] [2.1 GB] ncr53c875-0-<target 1, lun 0>: WIDE SCSI (16 bit) enabled. ncr53c875-0-<target 1, lun 0>: FAST SCSI-2 100ns (20 Mb/sec) offset 8. SCSI device sdb: hdwr sector= 512 bytes. Sectors= 4226725 [2063 MB] [2.1 GB] ncr53c875-0-<target 2, lun 0>: WIDE SCSI (16 bit) enabled. ncr53c875-0-<target 2, lun 0>: FAST SCSI-2 100ns (20 Mb/sec) offset 8. SCSI device sdc: hdwr sector= 512 bytes. Sectors= 4226725 [2063 MB] [2.1 GB] ncr53c875-0-<target 3, lun 0>: WIDE SCSI (16 bit) enabled. ncr53c875-0-<target 3, lun 0>: FAST SCSI-2 100ns (20 Mb/sec) offset 8. SCSI device sdd: hdwr sector= 512 bytes. Sectors= 4226725 [2063 MB] [2.1 GB] Partition check: sda: sda1 sdb: sdb1 sdc: sdc1 sdd: sdd1 sdd2 sdd3 sdd4 VFS: Mounted root (ext2 filesystem) readonly. Adding Swap: 130748k swap-space (priority -1) Serial driver version 4.13 with no serial options enabled tty00 at 0x03f8 (irq = 4) is a 16550A tty01 at 0x02f8 (irq = 3) is a 16550A PS/2 auxiliary pointing device detected -- driver installed.
maybe is there an interrupt conflict between eth0 and scsi? thnx in advance! Maurizio Marini Amm.ne Prov.le di Pesaro e Urbino Via Gramsci, 4 61100 - Pesaro (Italy) Tel. +39 (721) 359390 Fax +39 (721) 359350 p. Iva 00212000418 -- TO UNSUBSCRIBE FROM THIS MAILING LIST: e-mail the word "unsubscribe" to [EMAIL PROTECTED] . Trouble? e-mail to [EMAIL PROTECTED] .