I while I try to install Debian Etch using the actual net-installation
CD I encounter some problem for the partition already present on the laptop.
This machine is a dual-boot computer with windows and another Debian
installation that I want to re-install. None of these partiotion is
visible when I try to set the manual partitioning but I have to choose
between the guided partition or else to use the entire disk.
Is there a work-around?
The ata_piix module is loaded.
In attachment I enclose the dmesg output and also the lspci -nn output
is the following:
00:00.0 Host bridge [0600]: Intel Corporation Mobile 945GM/PM/GMS/940GML
and 945GT Express Memory Controller Hub [8086:27a0] (rev 03)
00:01.0 PCI bridge [0604]: Intel Corporation Mobile 945GM/PM/GMS/940GML
and 945GT Express PCI Express Root Port [8086:27a1] (rev 03)
00:1b.0 Audio device [0403]: Intel Corporation 82801G (ICH7 Family) High
Definition Audio Controller [8086:27d8] (rev 02)
00:1c.0 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI
Express Port 1 [8086:27d0] (rev 02)
00:1c.1 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI
Express Port 2 [8086:27d2] (rev 02)
00:1c.2 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI
Express Port 3 [8086:27d4] (rev 02)
00:1c.3 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI
Express Port 4 [8086:27d6] (rev 02)
00:1d.0 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family)
USB UHCI #1 [8086:27c8] (rev 02)
00:1d.1 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family)
USB UHCI #2 [8086:27c9] (rev 02)
00:1d.2 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family)
USB UHCI #3 [8086:27ca] (rev 02)
00:1d.3 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family)
USB UHCI #4 [8086:27cb] (rev 02)
00:1d.7 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family)
USB2 EHCI Controller [8086:27cc] (rev 02)
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge
[8086:2448] (rev e2)
00:1f.0 ISA bridge [0601]: Intel Corporation 82801GBM (ICH7-M) LPC
Interface Bridge [8086:27b9] (rev 02)
00:1f.2 IDE interface [0101]: Intel Corporation 82801GBM/GHM (ICH7
Family) Serial ATA Storage Controller IDE [8086:27c4] (rev 02)
00:1f.3 SMBus [0c05]: Intel Corporation 82801G (ICH7 Family) SMBus
Controller [8086:27da] (rev 02)
01:00.0 VGA compatible controller [0300]: ATI Technologies Inc Radeon
Mobility X1400 [1002:7145]
03:00.0 Network controller [0280]: Intel Corporation PRO/Wireless
3945ABG Network Connection [8086:4222] (rev 02)
04:00.0 Ethernet controller [0200]: Broadcom Corporation NetLink BCM5789
Gigabit Ethernet PCI Express [14e4:169d] (rev 21)
0a:09.0 CardBus bridge [0607]: Texas Instruments PCIxx12 Cardbus
Controller [104c:8039]
0a:09.1 FireWire (IEEE 1394) [0c00]: Texas Instruments PCIxx12 OHCI
Compliant IEEE 1394 Host Controller [104c:803a]
0a:09.2 Mass storage controller [0180]: Texas Instruments 5-in-1
Multimedia Card Reader (SD/MMC/MS/MS PRO/xD) [104c:803b]
Thank you in advance for whom that can solve this problem.
Best regards.
Gabriele
sbcore: registered new driver usbfs
usbcore: registered new driver hub
SCSI subsystem initialized
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 66
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 66, io mem 0xc8004000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
libata version 1.20 loaded.
USB Universal Host Controller Interface driver v3.0
Yenta: ISA IRQ mask 0x0cf8, PCI irq 201
Socket status: 30000006
pcmcia: parent PCI bridge I/O window: 0x3000 - 0x3fff
cs: IO port probe 0x3000-0x3fff: clean.
pcmcia: parent PCI bridge Memory window: 0xc8400000 - 0xc84fffff
pcmcia: parent PCI bridge Memory window: 0x50000000 - 0x51ffffff
ata_piix 0000:00:1f.2: version 1.05
ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ]
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 193
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0x18B0 irq 14
cs: IO port probe 0x100-0x3af: excluding 0x370-0x377
cs: IO port probe 0x3e0-0x4ff: excluding 0x3f0-0x3f7 0x4d0-0x4d7
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
ata1: dev 0 cfg 49:2f00 82:346b 83:7d09 84:6003 85:3469 86:3c09 87:6003 88:207f
ata1: dev 0 ATA-7, max UDMA/133, 195371568 sectors: LBA48
ata1: dev 0 configured for UDMA/133
scsi0 : ata_piix
Vendor: ATA Model: ST9100824AS Rev: 3.06
Type: Direct-Access ANSI SCSI revision: 05
ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x18B8 irq 15
usb 1-8: new high speed USB device using ehci_hcd and address 3
usb 1-8: configuration #1 chosen from 1 choice
ata2: dev 0 cfg 49:0f00 82:0000 83:0000 84:0000 85:0000 86:0000 87:0000 88:0407
ata2: dev 0 ATAPI, max UDMA/33
ata2: dev 0 configured for UDMA/33
scsi1 : ata_piix
Vendor: MATSHITA Model: DVD-RAM UJ-845S Rev: D201
Type: CD-ROM ANSI SCSI revision: 05
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 66
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 66, io base 0x00001800
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 193
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 193, io base 0x00001820
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 185
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 185, io base 0x00001840
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00c09f0000927ad2]
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: irq 169, io base 0x00001860
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
usb 2-2: new low speed USB device using uhci_hcd and address 2
SCSI device sda: 195371568 512-byte hdwr sectors (100030 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 195371568 512-byte hdwr sectors (100030 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1 sda2 < sda5 sda6 > sda3
sd 0:0:0:0: Attached scsi disk sda
sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda caddy
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
usb 2-2: configuration #1 chosen from 1 choice
sd 0:0:0:0: Attached scsi generic sg0 type 0
sr 1:0:0:0: Attached scsi generic sg1 type 5
usbcore: registered new driver hiddev
input: Logitech Optical USB Mouse as /class/input/input1
input: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-0000:00:1d.0-2
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: Thermal Zone [THRM] (56 C)
usbcore: registered new driver usbkbd
drivers/usb/input/usbkbd.c: :USB HID Boot Protocol keyboard driver
usbcore: registered new driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
usbcore: registered new driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core
vga16fb: initializing
vga16fb: mapped to 0xb00a0000
Console: switching to colour frame buffer device 80x30
fb0: VGA16 VGA frame buffer device
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
floppy0: no floppy controllers found
ide0: I/O resource 0x1F0-0x1F7 not free.
ide0: ports already in use, skipping probe
ide1: I/O resource 0x170-0x177 not free.
ide1: ports already in use, skipping probe
ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
ieee1394: sbp2: Try serialize_io=0 for better performance
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
tg3.c:v3.59.1 (August 25, 2006)
PCI: Enabling device 0000:04:00.0 (0000 -> 0002)
ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 18 (level, low) -> IRQ 185
PCI: Setting latency timer of device 0000:04:00.0 to 64
eth1394: eth0: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
eth1: Tigon3 [partno(BCM95789) rev 4201 PHY(5750)] (PCI Express)
10/100/1000BaseT Ethernet 00:16:36:38:80:af
eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[1]
eth1: dma_rwctrl[76180000] dma_mask[64-bit]
floppy0: no floppy controllers found
PM: Writing back config space on device 0000:04:00.0 at offset c (was 90000000,
writing 0)
PM: Writing back config space on device 0000:04:00.0 at offset 1 (was 100406,
writing 100006)
PM: Writing back config space on device 0000:04:00.0 at offset 1 (was 100406,
writing 100006)
tg3: eth1: Link is up at 1000 Mbps, full duplex.
tg3: eth1: Flow control is off for TX and off for RX.
floppy0: no floppy controllers found
program parted_devices is using a deprecated SCSI ioctl, please convert it to
SG_IO
program parted_devices is using a deprecated SCSI ioctl, please convert it to
SG_IO
JFS: nTxBlock = 8088, nTxLock = 64711
SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug
enabled
SGI XFS Quota Management subsystem
program parted_devices is using a deprecated SCSI ioctl, please convert it to
SG_IO
program parted_devices is using a deprecated SCSI ioctl, please convert it to
SG_IO
program parted_server is using a deprecated SCSI ioctl, please convert it to
SG_IO
