voila j'ai deja pose ce pb, on m'a deja repondu, mais ca ne donne rien
j'ai refait une image etc... etc...
je reexplique dont
controleur Tekram DC395U mdk7 Linux version 2.2.14-15mdk
mon probleme
carte scsi bien d�t�ct�e le jour de l'installation
apres reboot NADA, pas de scsi host detecte
lancement possible a la main par modprobe
voila le resulta d'un Dmesg apres lancement a la main
d'abord less question
Linux version 2.2.14-15mdk ([EMAIL PROTECTED]) (gcc version
2.95.2 19991024 (release)) #1 Tue Jan 4 22:24:20 CET 2000
Detected 200456937 Hz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 398.95 BogoMIPS
Memory: 127908k/131072k available (1092k kernel code, 416k reserved,
1592k data, 64k init, 0k bigmem)
Dentry hash table entries: 262144 (order 9, 2048k)
Buffer cache hash table entries: 131072 (order 7, 512k)
Page cache hash table entries: 32768 (order 5, 128k)
VFS: Diskquotas version dquot_6.4.0 initialized
CPU: Intel Pentium MMX stepping 03
Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
Checking 'hlt' instruction... OK.
Intel Pentium with F0 0F bug - workaround enabled.
POSIX conformance testing by UNIFIX
PCI: PCI BIOS revision 2.10 entry at 0xfdba1
PCI: Using configuration type 1
PCI: Probing PCI hardware
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0 for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
TCP: Hash tables configured (ehash 131072 bhash 65536)
Initializing RT netlink socket
Starting kswapd v 1.5
Detected PS/2 Mouse Port.
Serial driver version 4.27 with MANY_PORTS MULTIPORT SHARE_IRQ enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
pty: 256 Unix98 ptys configured
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.9)
Real Time Clock Driver v1.09
RAM disk driver initialized: 16 RAM disks of 4096K size
PIIX4: IDE controller on PCI bus 00 dev 39
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio
hda: FUJITSU MPC3084AT, ATA DISK drive
hdb: BCD-48SB CD-ROM, ATAPI CDROM drive
hdc: IBM-DJNA-371350, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: FUJITSU MPC3084AT, 8063MB w/0kB Cache, CHS=1027/255/63
hdc: IBM-DJNA-371350, 12949MB w/1966kB Cache, CHS=26310/16/63
hdb: ATAPI 44X CD-ROM drive, 128kB Cache
Uniform CDROM driver Revision: 2.56
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
md driver 0.90.0 MAX_MD_DEVS=256, MAX_REAL=12
raid5: measuring checksumming speed
raid5: MMX detected, trying high-speed MMX checksum routines
pII_mmx : 294.513 MB/sec
p5_mmx : 349.377 MB/sec
8regs : 213.360 MB/sec
32regs : 168.021 MB/sec
using fastest function: p5_mmx (349.377 MB/sec)
scsi : 0 hosts.<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<< ca comment je
le change et ou ?????
scsi : detected total.
md.c: sizeof(mdp_super_t) = 4096
Partition check:
hda: hda1 hda2 < hda5 hda6 > hda3
hdc: [PTBL] [1650/255/63] hdc1
autodetecting RAID arrays
autorun ...
... autorun DONE.
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 64k freed
Adding Swap: 216836k swap-space (priority -1)
via-rhine.c:v1.01 2/27/99 Written by Donald Becker
http://cesdis.gsfc.nasa.gov/linux/drivers/via-rhine.html
eth0: VIA VT3043 Rhine at 0xdc00, 00:80:c8:eb:bf:94, IRQ 11.
eth0: MII PHY found at address 8, status 0x782d advertising 05e1 Link
40a1.
DC395x (TRM-S1040) SCSI driver 1.10,
1999/07/19<<<<<<<<<<<<<<<<<<<<<<<<<<<< ca c apr�s le lancement a la main
DC395x: Used settings: AdaptID=7
DC395x (TRM-S1040): 1 adapters found
scsi0 : Tekram DC395U/UW/F DC315/U V1.10, 1999/07/19
scsi : 1 host.
DC395x: Sel Timeout IRQ
DC395x: Target 01: Sync transfer 100 ns, Offset 15
Vendor: SEAGATE Model: ST11200N Rev: 9300
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 1, lun 0
DC395x: Sel Timeout IRQ
DC395x: Sel Timeout IRQ
DC395x: Sel Timeout IRQ
DC395x: Target 05: Sync transfer 48 ns, Offset 15
Vendor: YAMAHA Model: CRW8424S Rev: 1.0d
Type: CD-ROM ANSI SCSI revision: 02
Detected scsi CD-ROM sr0 at scsi0, channel 0, id 5, lun 0
DC395x: Sel Timeout IRQ
sr0: scsi3-mmc drive: 24x/16x writer cd/rw xa/form2 cdda tray
SCSI device sda: hdwr sector= 512 bytes. Sectors= 2059140 [1005 MB] [1.0
GB]
sda: sda1
Au final comment je lance le module automatiquement, et me dite pas de
me compiler une image initrd, j'ai deja tester
Merci de votre comprehension
