I have some issue where I modified some config options for 2.6.24-19-lpia kernel. When I install the image, first I get pause for about 2minutes during install usb script.
Checking for device /dev/sda for installation source... Checking for device /dev/sdb for installation source... Checking for device /dev/sdc for installation source... Checking for device /dev/sdd for installation source... Sleeping for 5 seconds < waits here for couple minutes, and then continues successfully> First boot after install is done on scsi HDD (sda). It will take long time after (2min more than normal). Subsequent boots after that are normal and no delay? Any idea where I should be looking for this issue. I believe some kernel options is making this delay on first boot?? Regards naeem [ 33.796164] unionfs: debugging is not enabled [ 33.796811] Clocksource tsc unstable (delta = -1969696323 ns) [ 33.797794] Time: hpet clocksource has been installed. [ 33.808185] squashfs: version 3.3 (2007/10/31) Phillip Lougher [ 33.890492] usbcore: registered new interface driver asix [ 35.522298] usb-storage: device scan complete [ 35.526175] scsi 2:0:0:0: Direct-Access Generic Flash HS-CF 4.44 PQ: 0 ANSI: 0 [ 35.527467] scsi 2:0:0:1: Direct-Access Generic Flash HS-COMBO 4.44 PQ: 0 ANSI: 0 [ 35.532857] sd 2:0:0:0: [sdb] Attached SCSI removable disk [ 35.533063] sd 2:0:0:0: Attached scsi generic sg1 type 0 [ 35.583110] sd 2:0:0:1: [sdc] Attached SCSI removable disk [ 35.583369] sd 2:0:0:1: Attached scsi generic sg2 type 0 < 2min wait here...> [ 37.179097] usb 1-2: USB disconnect, address 2 [ 37.179190] usb 1-2.1: USB disconnect, address 4 [ 37.179282] usb 1-2.1.1: USB disconnect, address 6 [ 37.181124] usb 1-2.1.2: USB disconnect, address 7 [ 37.181786] usb 1-2.1.3: USB disconnect, address 8 [ 37.181877] usb 1-2.1.3.1: USB disconnect, address 9 [ 37.226117] usb 1-2.2: USB disconnect, address 5 [ 37.309008] kjournald starting. Commit interval 5 seconds [ 37.309793] EXT3 FS on sda2, internal journal [ 37.309933] EXT3-fs: recovery complete. [ 37.310564] EXT3-fs: mounted filesystem with ordered data mode. [ 37.342552] kjournald starting. Commit interval 5 seconds [ 37.345503] EXT3 FS on sda1, internal journal [ 37.345641] EXT3-fs: recovery complete. [ 37.346077] EXT3-fs: mounted filesystem with ordered data mode. [ 38.770707] iusbc 0000:00:1a.0: ---> iusbc_probe() [ 38.770739] ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 17 [ 38.770925] iusbc 0000:00:1a.0: ---> iusbc_reset() [ 38.770931] iusbc 0000:00:1a.0: <--- iusbc_reset() _______________________________________________ Moblin dev Mailing List [email protected] To manage or unsubscribe from this mailing list visit: https://lists.moblin.org/mailman/listinfo/dev or your user account on http://moblin.org once logged in. For more information on the Moblin Developer Mailing lists visit: http://moblin.org/community/mailing-lists
