Hi, Fred Try to load the ath5k driver with nohwcrypt=1.
Regards, Chun-Yeow On Thu, Aug 16, 2012 at 10:07 PM, fred veldini <[email protected]> wrote: > Hi Thomas, > > notes > iw version is 3.6 now > authsae is the latest released 8 days ago > running the latest kernel 3.5.0-rc6 from 80211s dev > > Thanks for your assistance > > Fred > > ----------------- > cut - authsae.conf > ----------------- > authsae: > { > sae: > { > debug = 480; > password = "supersecret2"; > group = [19, 26, 21, 25, 20]; > blacklist = 5; > thresh = 5; > lifetime = 3600; > }; > meshd: > { > meshid = "testmesh2"; > interface = "mesh0"; > passive = 0; > debug = 1; > mediaopt = 1; > band = "11a"; > channel = 149; > htmode="none"; > mcast-rate = 1; > }; > }; > > ----------------- > end of authsae.conf > ----------------- > ----------------- > cut - iw of ath5k card > ---------------- > Wiphy phy0 > Band 1: > Frequencies: > * 5040 MHz [8] (disabled) > * 5060 MHz [12] (disabled) > * 5080 MHz [16] (disabled) > * 5180 MHz [36] (20.0 dBm) (passive scanning, no IBSS) > * 5200 MHz [40] (20.0 dBm) (passive scanning, no IBSS) > * 5220 MHz [44] (20.0 dBm) (passive scanning, no IBSS) > * 5240 MHz [48] (20.0 dBm) (passive scanning, no IBSS) > * 5260 MHz [52] (disabled) > * 5280 MHz [56] (disabled) > * 5300 MHz [60] (disabled) > * 5320 MHz [64] (disabled) > * 5500 MHz [100] (disabled) > * 5520 MHz [104] (disabled) > * 5540 MHz [108] (disabled) > * 5560 MHz [112] (disabled) > * 5580 MHz [116] (disabled) > * 5600 MHz [120] (disabled) > * 5620 MHz [124] (disabled) > * 5640 MHz [128] (disabled) > * 5660 MHz [132] (disabled) > * 5680 MHz [136] (disabled) > * 5700 MHz [140] (disabled) > * 5745 MHz [149] (20.0 dBm) (passive scanning, no IBSS) > * 5765 MHz [153] (20.0 dBm) (passive scanning, no IBSS) > * 5785 MHz [157] (20.0 dBm) (passive scanning, no IBSS) > * 5805 MHz [161] (20.0 dBm) (passive scanning, no IBSS) > * 5825 MHz [165] (20.0 dBm) (passive scanning, no IBSS) > Bitrates (non-HT): > * 6.0 Mbps > * 9.0 Mbps > * 12.0 Mbps > * 18.0 Mbps > * 24.0 Mbps > * 36.0 Mbps > * 48.0 Mbps > * 54.0 Mbps > max # scan SSIDs: 4 > max scan IEs length: 2289 bytes > Coverage class: 0 (up to 0m) > Supported Ciphers: > * WEP40 (00-0f-ac:1) > * WEP104 (00-0f-ac:5) > * TKIP (00-0f-ac:2) > * CCMP (00-0f-ac:4) > Available Antennas: TX 0x3 RX 0x3 > Configured Antennas: TX 0x3 RX 0x3 > Supported interface modes: > * IBSS > * managed > * AP > * AP/VLAN > * monitor > * mesh point > software interface modes (can always be added): > * AP/VLAN > * monitor > valid interface combinations: > * #{ managed } <= 2048, #{ AP, mesh point } <= 4, > total <= 2048, #channels <= 1 > Supported commands: > * new_interface > * set_interface > * new_key > * start_ap > * new_station > * new_mpath > * set_mesh_config > * set_bss > * authenticate > * associate > * deauthenticate > * disassociate > * join_ibss > * join_mesh > * set_tx_bitrate_mask > * frame > * frame_wait_cancel > * set_wiphy_netns > * set_channel > * set_wds_peer > * probe_client > * set_noack_map > * register_beacons > * testmode > * connect > * disconnect > Supported TX frame types: > * IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 > 0xc0 0xd0 0xe0 0xf0 > * managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 > 0xb0 0xc0 0xd0 0xe0 0xf0 > * AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 > 0xc0 0xd0 0xe0 0xf0 > * AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 > 0xb0 0xc0 0xd0 0xe0 0xf0 > * mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 > 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 > * P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 > 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 > * P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 > 0xb0 0xc0 0xd0 0xe0 0xf0 > Supported RX frame types: > * IBSS: 0xb0 0xc0 0xd0 > * managed: 0x40 0xd0 > * AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 > * AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 > * mesh point: 0xb0 0xc0 0xd0 > * P2P-client: 0x40 0xd0 > * P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 > Device supports RSN-IBSS. > HT Capability overrides: > * MCS: ff ff ff ff ff ff ff ff ff ff > * maximum A-MSDU length > * supported channel width > * short GI for 40 MHz > * max A-MPDU length exponent > * min MPDU start spacing > Device supports TX status socket option. > Device supports HT-IBSS. > ------------------ > cut - end of iw list for ath5k > ------------------ > ------------------ > cut - start iw list ath9k card > ----------------- > Wiphy phy1 > Band 1: > Capabilities: 0x104e > HT20/HT40 > SM Power Save disabled > RX HT40 SGI > No RX STBC > Max AMSDU length: 3839 bytes > DSSS/CCK HT40 > Maximum RX AMPDU length 65535 bytes (exponent: 0x003) > Minimum RX AMPDU time spacing: 8 usec (0x06) > HT TX/RX MCS rate indexes supported: 0-15 > Frequencies: > * 2412 MHz [1] (20.0 dBm) > * 2417 MHz [2] (20.0 dBm) > * 2422 MHz [3] (20.0 dBm) > * 2427 MHz [4] (20.0 dBm) > * 2432 MHz [5] (20.0 dBm) > * 2437 MHz [6] (20.0 dBm) > * 2442 MHz [7] (20.0 dBm) > * 2447 MHz [8] (20.0 dBm) > * 2452 MHz [9] (20.0 dBm) > * 2457 MHz [10] (20.0 dBm) > * 2462 MHz [11] (20.0 dBm) > * 2467 MHz [12] (disabled) > * 2472 MHz [13] (disabled) > * 2484 MHz [14] (disabled) > Bitrates (non-HT): > * 1.0 Mbps > * 2.0 Mbps (short preamble supported) > * 5.5 Mbps (short preamble supported) > * 11.0 Mbps (short preamble supported) > * 6.0 Mbps > * 9.0 Mbps > * 12.0 Mbps > * 18.0 Mbps > * 24.0 Mbps > * 36.0 Mbps > * 48.0 Mbps > * 54.0 Mbps > Band 2: > Capabilities: 0x104e > HT20/HT40 > SM Power Save disabled > RX HT40 SGI > No RX STBC > Max AMSDU length: 3839 bytes > DSSS/CCK HT40 > Maximum RX AMPDU length 65535 bytes (exponent: 0x003) > Minimum RX AMPDU time spacing: 8 usec (0x06) > HT TX/RX MCS rate indexes supported: 0-15 > Frequencies: > * 5180 MHz [36] (20.0 dBm) (passive scanning, no IBSS) > * 5200 MHz [40] (20.0 dBm) (passive scanning, no IBSS) > * 5220 MHz [44] (20.0 dBm) (passive scanning, no IBSS) > * 5240 MHz [48] (20.0 dBm) (passive scanning, no IBSS) > * 5260 MHz [52] (disabled) > * 5280 MHz [56] (disabled) > * 5300 MHz [60] (disabled) > * 5320 MHz [64] (disabled) > * 5500 MHz [100] (disabled) > * 5520 MHz [104] (disabled) > * 5540 MHz [108] (disabled) > * 5560 MHz [112] (disabled) > * 5580 MHz [116] (disabled) > * 5600 MHz [120] (disabled) > * 5620 MHz [124] (disabled) > * 5640 MHz [128] (disabled) > * 5660 MHz [132] (disabled) > * 5680 MHz [136] (disabled) > * 5700 MHz [140] (disabled) > * 5745 MHz [149] (20.0 dBm) (passive scanning, no IBSS) > * 5765 MHz [153] (20.0 dBm) (passive scanning, no IBSS) > * 5785 MHz [157] (20.0 dBm) (passive scanning, no IBSS) > * 5805 MHz [161] (20.0 dBm) (passive scanning, no IBSS) > * 5825 MHz [165] (20.0 dBm) (passive scanning, no IBSS) > Bitrates (non-HT): > * 6.0 Mbps > * 9.0 Mbps > * 12.0 Mbps > * 18.0 Mbps > * 24.0 Mbps > * 36.0 Mbps > * 48.0 Mbps > * 54.0 Mbps > max # scan SSIDs: 4 > max scan IEs length: 2257 bytes > Coverage class: 0 (up to 0m) > Supported Ciphers: > * WEP40 (00-0f-ac:1) > * WEP104 (00-0f-ac:5) > * TKIP (00-0f-ac:2) > * CCMP (00-0f-ac:4) > * CMAC (00-0f-ac:6) > Available Antennas: TX 0x7 RX 0x7 > Configured Antennas: TX 0x7 RX 0x7 > Supported interface modes: > * IBSS > * managed > * AP > * AP/VLAN > * WDS > * monitor > * mesh point > * P2P-client > * P2P-GO > software interface modes (can always be added): > * AP/VLAN > * monitor > valid interface combinations: > * #{ managed, WDS, P2P-client } <= 2048, #{ AP, mesh point, P2P-GO > } <= 8, > total <= 2048, #channels <= 1 > Supported commands: > * new_interface > * set_interface > * new_key > * start_ap > * new_station > * new_mpath > * set_mesh_config > * set_bss > * authenticate > * associate > * deauthenticate > * disassociate > * join_ibss > * join_mesh > * remain_on_channel > * set_tx_bitrate_mask > * frame > * frame_wait_cancel > * set_wiphy_netns > * set_channel > * set_wds_peer > * tdls_mgmt > * tdls_oper > * probe_client > * set_noack_map > * register_beacons > * testmode > * connect > * disconnect > Supported TX frame types: > * IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 > 0xc0 0xd0 0xe0 0xf0 > * managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 > 0xb0 0xc0 0xd0 0xe0 0xf0 > * AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 > 0xc0 0xd0 0xe0 0xf0 > * AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 > 0xb0 0xc0 0xd0 0xe0 0xf0 > * mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 > 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 > * P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 > 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 > * P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 > 0xb0 0xc0 0xd0 0xe0 0xf0 > Supported RX frame types: > * IBSS: 0xb0 0xc0 0xd0 > * managed: 0x40 0xd0 > * AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 > * AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 > * mesh point: 0xb0 0xc0 0xd0 > * P2P-client: 0x40 0xd0 > * P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 > Device supports RSN-IBSS. > HT Capability overrides: > * MCS: ff ff ff ff ff ff ff ff ff ff > * maximum A-MSDU length > * supported channel width > * short GI for 40 MHz > * max A-MPDU length exponent > * min MPDU start spacing > Device supports TX status socket option. > Device supports HT-IBSS. > ------------- > cut - end of iw list ath9k card > ------------- > > > > > > On Wed, Aug 15, 2012 at 5:10 PM, Thomas Pedersen <[email protected]> wrote: >> >> Hi Fred, >> >> On Tue, Aug 14, 2012 at 8:45 AM, fred veldini <[email protected]> >> wrote: >> > Hello again, I don't know if this is a isolated issue (to me) but I >> > will >> > ask the question >> > >> > If im using the ath9k driver (with appropriate hardware) and authsae, >> > everything runs fine. >> > >> > if Im using the ath5k driver (with appropriate hardware) and authsae I >> > get >> > errors >> > >> > nlcfg rates hexdump >> > ---------- >> > >> > wiphy reported no rates! >> >> This is strange. Can you please provide your full authsae.conf as well >> as the 'iw phy info' output for the ath5k phy? >> >> Thomas >> _______________________________________________ >> Devel mailing list >> [email protected] >> http://lists.open80211s.org/cgi-bin/mailman/listinfo/devel > > > > _______________________________________________ > Devel mailing list > [email protected] > http://lists.open80211s.org/cgi-bin/mailman/listinfo/devel > _______________________________________________ Devel mailing list [email protected] http://lists.open80211s.org/cgi-bin/mailman/listinfo/devel
