On 14:08 Fri 16 Nov , Nicolas Ferre wrote: > On 10/19/2012 04:19 AM, Jean-Christophe PLAGNIOL-VILLARD : > > CPU Module with ATMEL AT91SAM9G45 > > http://www.ronetix.at/pm9g45.html > > > > Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]> > > Cc: Nicolas Ferre <[email protected]> > > Ok, queued in at91-3.8-dt branch. > > I had to modify the Makefile part of it to match current move to > arch/arm/boot/dts/Makefile. > > Acked-by: Nicolas Ferre <[email protected]> I prefer to go via linus W I've other updte for the macb on the top of it
ditto for the rm9200 Best Regards, J. > > > --- > > arch/arm/boot/dts/Makefile | 1 + > > arch/arm/boot/dts/pm9g45.dts | 144 > > ++++++++++++++++++++++++++++++++++++++++++ > > 2 files changed, 145 insertions(+) > > create mode 100644 arch/arm/boot/dts/pm9g45.dts > > > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > > index a9b051a..627b6ad 100644 > > --- a/arch/arm/boot/dts/Makefile > > +++ b/arch/arm/boot/dts/Makefile > > @@ -19,6 +19,7 @@ dtb-$(CONFIG_ARCH_AT91) += tny_a9g20.dtb > > dtb-$(CONFIG_ARCH_AT91) += usb_a9g20.dtb > > # sam9g45 > > dtb-$(CONFIG_ARCH_AT91) += at91sam9m10g45ek.dtb > > +dtb-$(CONFIG_ARCH_AT91) += pm9g45.dtb > > # sam9n12 > > dtb-$(CONFIG_ARCH_AT91) += at91sam9n12ek.dtb > > # sam9x5 > > diff --git a/arch/arm/boot/dts/pm9g45.dts b/arch/arm/boot/dts/pm9g45.dts > > new file mode 100644 > > index 0000000..b0c258d > > --- /dev/null > > +++ b/arch/arm/boot/dts/pm9g45.dts > > @@ -0,0 +1,144 @@ > > +/* > > + * pm9g45.dts - Device Tree file for Ronetix pm9g45 board > > + * > > + * Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD > > <[email protected]> > > + * > > + * Licensed under GPLv2. > > + */ > > +/dts-v1/; > > +/include/ "at91sam9g45.dtsi" > > + > > +/ { > > + model = "Ronetix pm9g45"; > > + compatible = "ronetix,pm9g45", "atmel,at91sam9g45", "atmel,at91sam9"; > > + > > + chosen { > > + bootargs = "console=ttyS0,115200"; > > + }; > > + > > + memory { > > + reg = <0x70000000 0x8000000>; > > + }; > > + > > + clocks { > > + #address-cells = <1>; > > + #size-cells = <1>; > > + ranges; > > + > > + main_clock: clock@0 { > > + compatible = "atmel,osc", "fixed-clock"; > > + clock-frequency = <12000000>; > > + }; > > + }; > > + > > + ahb { > > + apb { > > + dbgu: serial@ffffee00 { > > + status = "okay"; > > + }; > > + > > + pinctrl@fffff200 { > > + > > + board { > > + pinctrl_board_nand: nand0-board { > > + atmel,pins = > > + <3 3 0x0 0x1 /* PD3 > > gpio RDY pin pull_up*/ > > + 2 14 0x0 0x1>; /* PC14 > > gpio enable pin pull_up */ > > + }; > > + }; > > + }; > > + > > + macb0: ethernet@fffbc000 { > > + phy-mode = "rmii"; > > + status = "okay"; > > + }; > > + }; > > + > > + nand0: nand@40000000 { > > + nand-bus-width = <8>; > > + nand-ecc-mode = "soft"; > > + nand-on-flash-bbt; > > + pinctrl-0 = <&pinctrl_board_nand>; > > + > > + gpios = <&pioD 3 0 > > + &pioC 14 0 > > + 0 > > + >; > > + > > + status = "okay"; > > + > > + at91bootstrap@0 { > > + label = "at91bootstrap"; > > + reg = <0x0 0x20000>; > > + }; > > + > > + barebox@20000 { > > + label = "barebox"; > > + reg = <0x20000 0x40000>; > > + }; > > + > > + bareboxenv@60000 { > > + label = "bareboxenv"; > > + reg = <0x60000 0x1A0000>; > > + }; > > + > > + kernel@200000 { > > + label = "bareboxenv2"; > > + reg = <0x200000 0x300000>; > > + }; > > + > > + kernel@500000 { > > + label = "root"; > > + reg = <0x500000 0x400000>; > > + }; > > + > > + data@900000 { > > + label = "data"; > > + reg = <0x900000 0x8340000>; > > + }; > > + }; > > + > > + usb0: ohci@00700000 { > > + status = "okay"; > > + num-ports = <2>; > > + }; > > + > > + usb1: ehci@00800000 { > > + status = "okay"; > > + }; > > + }; > > + > > + leds { > > + compatible = "gpio-leds"; > > + > > + led0 { > > + label = "led0"; > > + gpios = <&pioD 0 1>; > > + linux,default-trigger = "nand-disk"; > > + }; > > + > > + led1 { > > + label = "led1"; > > + gpios = <&pioD 31 0>; > > + linux,default-trigger = "heartbeat"; > > + }; > > + }; > > + > > + gpio_keys { > > + compatible = "gpio-keys"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + right { > > + label = "SW4"; > > + gpios = <&pioE 7 1>; > > + linux,code = <106>; > > + }; > > + > > + up { > > + label = "SW3"; > > + gpios = <&pioE 8 1>; > > + linux,code = <103>; > > + }; > > + }; > > +}; > > > > > -- > Nicolas Ferre _______________________________________________ devicetree-discuss mailing list [email protected] https://lists.ozlabs.org/listinfo/devicetree-discuss
