On 11/16/2012 02:28 PM, Jean-Christophe PLAGNIOL-VILLARD : > On 14:08 Fri 16 Nov , Nicolas Ferre wrote: >> On 10/19/2012 04:19 AM, Jean-Christophe PLAGNIOL-VILLARD : >>> CPU Module with ATMEL AT91SAM9G45 >>> http://www.ronetix.at/pm9g45.html >>> >>> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]> >>> Cc: Nicolas Ferre <[email protected]> >> >> Ok, queued in at91-3.8-dt branch. >> >> I had to modify the Makefile part of it to match current move to >> arch/arm/boot/dts/Makefile. >> >> Acked-by: Nicolas Ferre <[email protected]> > I prefer to go via linus W I've other updte for the macb on the top of it
Fine... Be careful about macb, there are many things happening right now in net-next for this interface! > ditto for the rm9200 Noted. Thanks. Bye, >>> --- >>> arch/arm/boot/dts/Makefile | 1 + >>> arch/arm/boot/dts/pm9g45.dts | 144 >>> ++++++++++++++++++++++++++++++++++++++++++ >>> 2 files changed, 145 insertions(+) >>> create mode 100644 arch/arm/boot/dts/pm9g45.dts >>> >>> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile >>> index a9b051a..627b6ad 100644 >>> --- a/arch/arm/boot/dts/Makefile >>> +++ b/arch/arm/boot/dts/Makefile >>> @@ -19,6 +19,7 @@ dtb-$(CONFIG_ARCH_AT91) += tny_a9g20.dtb >>> dtb-$(CONFIG_ARCH_AT91) += usb_a9g20.dtb >>> # sam9g45 >>> dtb-$(CONFIG_ARCH_AT91) += at91sam9m10g45ek.dtb >>> +dtb-$(CONFIG_ARCH_AT91) += pm9g45.dtb >>> # sam9n12 >>> dtb-$(CONFIG_ARCH_AT91) += at91sam9n12ek.dtb >>> # sam9x5 >>> diff --git a/arch/arm/boot/dts/pm9g45.dts b/arch/arm/boot/dts/pm9g45.dts >>> new file mode 100644 >>> index 0000000..b0c258d >>> --- /dev/null >>> +++ b/arch/arm/boot/dts/pm9g45.dts >>> @@ -0,0 +1,144 @@ >>> +/* >>> + * pm9g45.dts - Device Tree file for Ronetix pm9g45 board >>> + * >>> + * Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD >>> <[email protected]> >>> + * >>> + * Licensed under GPLv2. >>> + */ >>> +/dts-v1/; >>> +/include/ "at91sam9g45.dtsi" >>> + >>> +/ { >>> + model = "Ronetix pm9g45"; >>> + compatible = "ronetix,pm9g45", "atmel,at91sam9g45", "atmel,at91sam9"; >>> + >>> + chosen { >>> + bootargs = "console=ttyS0,115200"; >>> + }; >>> + >>> + memory { >>> + reg = <0x70000000 0x8000000>; >>> + }; >>> + >>> + clocks { >>> + #address-cells = <1>; >>> + #size-cells = <1>; >>> + ranges; >>> + >>> + main_clock: clock@0 { >>> + compatible = "atmel,osc", "fixed-clock"; >>> + clock-frequency = <12000000>; >>> + }; >>> + }; >>> + >>> + ahb { >>> + apb { >>> + dbgu: serial@ffffee00 { >>> + status = "okay"; >>> + }; >>> + >>> + pinctrl@fffff200 { >>> + >>> + board { >>> + pinctrl_board_nand: nand0-board { >>> + atmel,pins = >>> + <3 3 0x0 0x1 /* PD3 >>> gpio RDY pin pull_up*/ >>> + 2 14 0x0 0x1>; /* PC14 >>> gpio enable pin pull_up */ >>> + }; >>> + }; >>> + }; >>> + >>> + macb0: ethernet@fffbc000 { >>> + phy-mode = "rmii"; >>> + status = "okay"; >>> + }; >>> + }; >>> + >>> + nand0: nand@40000000 { >>> + nand-bus-width = <8>; >>> + nand-ecc-mode = "soft"; >>> + nand-on-flash-bbt; >>> + pinctrl-0 = <&pinctrl_board_nand>; >>> + >>> + gpios = <&pioD 3 0 >>> + &pioC 14 0 >>> + 0 >>> + >; >>> + >>> + status = "okay"; >>> + >>> + at91bootstrap@0 { >>> + label = "at91bootstrap"; >>> + reg = <0x0 0x20000>; >>> + }; >>> + >>> + barebox@20000 { >>> + label = "barebox"; >>> + reg = <0x20000 0x40000>; >>> + }; >>> + >>> + bareboxenv@60000 { >>> + label = "bareboxenv"; >>> + reg = <0x60000 0x1A0000>; >>> + }; >>> + >>> + kernel@200000 { >>> + label = "bareboxenv2"; >>> + reg = <0x200000 0x300000>; >>> + }; >>> + >>> + kernel@500000 { >>> + label = "root"; >>> + reg = <0x500000 0x400000>; >>> + }; >>> + >>> + data@900000 { >>> + label = "data"; >>> + reg = <0x900000 0x8340000>; >>> + }; >>> + }; >>> + >>> + usb0: ohci@00700000 { >>> + status = "okay"; >>> + num-ports = <2>; >>> + }; >>> + >>> + usb1: ehci@00800000 { >>> + status = "okay"; >>> + }; >>> + }; >>> + >>> + leds { >>> + compatible = "gpio-leds"; >>> + >>> + led0 { >>> + label = "led0"; >>> + gpios = <&pioD 0 1>; >>> + linux,default-trigger = "nand-disk"; >>> + }; >>> + >>> + led1 { >>> + label = "led1"; >>> + gpios = <&pioD 31 0>; >>> + linux,default-trigger = "heartbeat"; >>> + }; >>> + }; >>> + >>> + gpio_keys { >>> + compatible = "gpio-keys"; >>> + #address-cells = <1>; >>> + #size-cells = <0>; >>> + >>> + right { >>> + label = "SW4"; >>> + gpios = <&pioE 7 1>; >>> + linux,code = <106>; >>> + }; >>> + >>> + up { >>> + label = "SW3"; >>> + gpios = <&pioE 8 1>; >>> + linux,code = <103>; >>> + }; >>> + }; >>> +}; >>> >> >> >> -- >> Nicolas Ferre > > -- Nicolas Ferre _______________________________________________ devicetree-discuss mailing list [email protected] https://lists.ozlabs.org/listinfo/devicetree-discuss
