On 04/08/2013 07:12 AM, Prabhakar Lad wrote: > On Wed, Apr 3, 2013 at 10:14 PM, Stephen Warren <[email protected]> wrote: >> On 04/03/2013 03:16 AM, Prabhakar Lad wrote: >>> Hi Linus/Stephen, >>> >>> I am working adding DT nodes for DA850. ... >>> But while booting I see the following boot log:- >>> ... >>> cpuidle: using governor menu >>> TCP: cubic registered >>> NET: Registered protocol family 17 >>> pinctrl-single 1c14120.pinmux: pin 1c14130 already requested by >>> davinci_mdio.0; cannot claim for i2c_davinci.1 >>> pinctrl-single 1c14120.pinmux: pin-4 (i2c_davinci.1) status -22 >>> pinctrl-single 1c14120.pinmux: could not request pin 4 on device >>> pinctrl-single >>> console [netcon0] enabled >>> .... >>> >>> This is because the mdio and i2c are using same pin 0x10, >> >> How can two devices use the same pin? I mean physically, in hardware? >> >> Is this because pinctrl-single uses the register address as the pin >> number, whereas you have registers which configure multiple pins at > > Yes you are correct, we have registers which configure multiple pins at once. > For example for above Pin Multiplexing Control 4 Register (Pinmux4) > [1] page(250) : - > > PINMUX4_31_28 --> SP1_SCS[2]/UART1_TXD/SATA_CP_POD/GP1[0] Control > PINMUX4_27_24 --> SPI1_SCS[3]/UART1_RXD/SATA_LED/GP1[1] Control > PINMUX4_23_20 --> SPI1_SCS[4]/UART2_TXD/I2C1_SDA/GP1[2] Control > PINMUX4_19_16 --> SPI1_SCS[5]/UART2_RXD/I2C1_SCL/GP1[3] Control > PINMUX4_15_12 --> SPI1_SCS[6]/I2C0_SDA/TM64P3_OUT12/GP1[4] Control > PINMUX4_11_8 --> SPI1_SCS[7]/I2C0_SCL/TM64P2_OUT12/GP1[5] Control > PINMUX4_7_4 --> SPI0_SCS[0]/TM64P1_OUT12/GP1[6]/MDIO_D/TM64P1_IN12 Control > PINMUX4_3_0 --> SPI0_SCS[1]/TM64P0_OUT12/GP1[7]/MDIO_CLK/TM64P0_IN12 Control > >> once? If so, your hardware isn't something that can be represented by >> pinctrl-single. > > What is the alternative for such case ? any pointer would be helpful. > > [1] > http://www.ti.com/general/docs/lit/getliterature.tsp?literatureNumber=spruh77a&fileType=pdf
Tony previously replied: Tony wrote: > Tony wrote: >> ??? wrote: >>> Prabhakar wrote: >>>> Is there any >>>> alternative way to handle if the two node's are using same pins any >>>> pointers could be very much helpful ? >> >> It could also that the mux register(s) follow the one-mux-per-bit >> mapping. >> >> In that case pinctrl-single,bits option as documented in the >> Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt. > > Oh it's already using pinctrl-single,bits option. Maybe there's a > bug, adding Peter to cc. So I guess you need to debug the code to see why that option isn't working for you. Going back to your original question above though, if the pinctrl-single driver doesn't work out for you, then you'd need to create a custom pinctrl driver for your chip, just like the many examples already in drivers/pinctrl. _______________________________________________ devicetree-discuss mailing list [email protected] https://lists.ozlabs.org/listinfo/devicetree-discuss
