Hi,
On 03/12/2014 11:09 AM, Maxime Ripard wrote:
> Hi,
>
> On Tue, Mar 11, 2014 at 04:51:00PM +0100, Hans de Goede wrote:
>> SUN4I_IRQ_VECTOR_REG containing 0 can mean one of 2 things:
>> 1) irq 0 pending
>> 2) no more irqs pending
>>
>> So we must loop always atleast once to make irq 0 work, otherwise irq 0
>> will never get serviced and we end up with a hard hang because
>> sun4i_handle_irq gets re-entered constantly.
>>
>> Signed-off-by: Hans de Goede <[email protected]>
>> ---
>> drivers/irqchip/irq-sun4i.c | 10 ++++++++--
>> 1 file changed, 8 insertions(+), 2 deletions(-)
>>
>> diff --git a/drivers/irqchip/irq-sun4i.c b/drivers/irqchip/irq-sun4i.c
>> index a5438d8..3761bf1 100644
>> --- a/drivers/irqchip/irq-sun4i.c
>> +++ b/drivers/irqchip/irq-sun4i.c
>> @@ -140,10 +140,16 @@ static asmlinkage void __exception_irq_entry
>> sun4i_handle_irq(struct pt_regs *re
>> {
>> u32 irq, hwirq;
>>
>> + /*
>> + * hwirq == 0 can mean one of 2 things:
>> + * 1) irq 0 pending
>> + * 2) no more irqs pending
>
> 3) spurious interrupt.
>
>> + * So loop always atleast once to make irq 0 work.
>> + */
>> hwirq = readl(sun4i_irq_base + SUN4I_IRQ_VECTOR_REG) >> 2;
>> - while (hwirq != 0) {
>> + do {
>
> I'd at least lookup in the pending register to see if the interrupt 0
> was actually triggered. Otherwise, you could end up with spurious
> handler calls on the interrupt 0.
Yes, I was already worrying about this myself after sending the patch,
and considered reading pending too.
>
>> irq = irq_find_mapping(sun4i_irq_domain, hwirq);
>> handle_IRQ(irq, regs);
>> hwirq = readl(sun4i_irq_base + SUN4I_IRQ_VECTOR_REG) >> 2;
>
> And you end up with the same issue if there's a first != 0 interrupt,
> and then the interrupt 0.
No, before my fix sun4i_handle_irq would be called continuously since we
were never handling irq 0, so if this happens we will simply drop out
of sun4i_handle_irq only to immediately get recalled, this does make this
scenario more expensive, but things will still work, while it saves an
also not cheap read from SUN4I_IRQ_PENDING_REG(0) for each regular
interrupt.
Note I agree the spurious irq case is an issue, as said that has me
worried too.
> What about something like:
>
> while (1) {
> hwirq = readl(sun4i_irq_base + SUN4I_IRQ_VECTOR_REG) >> 2;
> if (!hwirq)
> if (!(readl(sun4i_irq_base + SUN4I_IRQ_PENDING_REG(0)) &
> BIT(0)))
> break;
>
> irq = irq_find_mapping(sun4i_irq_domain, hwirq);
> handle_IRQ(irq, regs);
> }
Yes that should work nicely, but for the straight path it means reading pending
once for each interrupt.
I agree we need to read pending before calling handle_IRQ for irq 0, but
we only need to do so if the first read from SUN4I_IRQ_VECTOR_REG == 0,
on any subsequent reads from SUN4I_IRQ_VECTOR_REG returning 0 we can exit
immediately, in the worst case we'll get called again, and then do the
right thing.
IE something like this:
hwirq = readl(sun4i_irq_base + SUN4I_IRQ_VECTOR_REG) >> 2;
/* Ensure hwirq == 0 is because of irq 0 pending */
if (hwirq == 0 && !(readl(sun4i_irq_base + SUN4I_IRQ_PENDING_REG(0)) &
BIT(0)))
return;
do {
irq = irq_find_mapping(sun4i_irq_domain, hwirq);
handle_IRQ(irq, regs);
hwirq = readl(sun4i_irq_base + SUN4I_IRQ_VECTOR_REG) >> 2;
} while (hwirq);
Note untested, and this might be unnecessary optimization. So let me know which
version you prefer and I'll give it a test run.
Regards,
Hans
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
