We had no response to about 4 emails except May 1 (europe holiday) and response was "out of office" and finally a response from Hawker Pacific and $1000 + GST which is double the original price and they did not respond to parts like fuel pump etc.
It would be good if Bernard were the agent again as gather he gives good service. Think he was helpful with Nigel's wing Ian M 27 May 2012 17:33, John C <[email protected]> wrote: > ** > Hi Rob, > > They won't deal direct anymore - only via Hawker Pacific. > Just costs more and takes longer. > > John. > > > ----- Original Message ----- > *From:* Rob Thompson <[email protected]> > *To:* [email protected] > *Sent:* Sunday, May 27, 2012 1:17 PM > *Subject:* [DOG mailing list] Diamond Aircraft tech support contact > detalails needed > > I just went to Diamond Aircraft's website and no email addresses. > Anyone know a contact I can deal with about the 3000 hour inspection? > Rob > PO Box 129, > Lawson, NSW, 2783. > mobile 0429 493828 > > > > > > > > > > > > > > > > > > > > ............................................. > > --- On *Sat, 26/5/12, John Viney <[email protected]>* wrote: > > > From: John Viney <[email protected]> > Subject: Re: [DOG mailing list] nuts on rear of front plate in 3 position > hoffmann/MT prop > To: [email protected] > Received: Saturday, 26 May, 2012, 2:47 AM > > Hi Ian, > > Min amount of material required around the hole varies with type of > material and loading it experiences (aluminium and cast iron need more than > mild steel & High carbon steels need even less, but you are right and in > the Hoffmann thrust ring less than hole dia x 1 is not good design. > > Nylock nuts in reverse for the inner nuts on the Hoffmann pitch change > rods would be an acceptable fix, but on pushrod ends is not the best > answer as it will stay locked to the rod thread but the nut face can still > loosen against the rod. Best method is a double tab washer which locks one > tab against a flat on the pushrod ( not on all rods, you may have to file > one) and another tab against the nut. Some rod ends have a groove in > the thread for a locktab with an internal tang, again one tab against the > flat on the rod & another against the nut. > > Re; supplies of FC332 see my earlier e-mail. I am happy to purchase & > post to any owner who has trouble obtaining FC332-4, -6 & -8 hose, also > correct size Oetiker clamps. Type 154 (single ear stainless steel with > liner) for hose attachment, and type 101 (2 ear zinc coated steel) for > securing firesleeving. > > regards > JGV > > ----- Original Message ----- > *From:* Ian Mc Phee <http://mc/[email protected]> > *To:* DOG LIST <http://mc/[email protected]> > *Sent:* Friday, May 25, 2012 8:55 PM > *Subject:* [DOG mailing list] nuts on rear of front plate in 3 position > hoffmann/MT prop > > A friend with a Ximango has had the inside nuts (non locking) coming loose > and been talking to Eric Weston he has replaced them with nylon lock nuts > put on in reverse so now they really lock on the prop front plate. > > I am not impressed how the hole size is increased in plate from 6mm to 8mm > (for the 8mm rods) BUT the plate is made no longer. I seem to remember > somewhere in engineering there should be beef of 1.5 times the diameter of > the hole on the outside of the hole ie 12mm. No way it is about 6 or 7 mm > from memory. Don't these makers have any engineers working for them any > more or look at what they post on EASA site when they decide to issue a SB? > > > As some know motor PIKs have had the locking nuts coming loose on ball rod > ends in the wing which can cause ball rod ends to crack and break (It > happened to our PIK E 15 yrs ago) Anyhow a friend with a PIK replaced all > the ordinary 6mm nuts with nylon locking nuts and screwed them on in > reverse so now they positively lock the ball rod end to push rod. > > Both seem like a good idea to me to solve a problem which the makers never > thought of. > > I am not at all impressed with the service provided by the so called > Diamond agent in Aus Hawker Pacific. Took guess 6 emails to Austria and > only on May 1 (Europe Public Holiday) did I get several "out of office" > emails so Austria were getting them. Eventually Australia replied but no > mention of the various spares I asked prices of. Not impressed compared to > 4 years ago I got a phone call from Austria 30 seconds after I pressed the > send button on an email. That was the then Canadian speaking Parts > Manager. in Austria. S L A C K if you ask me > > Finally does anybody know where to buy Aeroquip AC 332-4 (or -6) blue fuel > hose as my source in Brisbane no longer stock same. Has anybody used the > aviation Aeroquip AE-466-4 etc hose The main advantage of this hose is it > has red cover of fireproofing on the hose at manufacture but is expensive I > guess.. > > Ian McPhee > (PS I suppose I am just a grump) > > > >
