On Thu, Jul 13, 2017 at 04:13:06PM +0200, Maxime Ripard wrote:
> The Allwinner SoCs usually come with a DSI encoder. Add a binding for it.
>
> Signed-off-by: Maxime Ripard <maxime.rip...@free-electrons.com>
> ---
> Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt | 85 +++++++-
> 1 file changed, 85 insertions(+)
> create mode 100644
> Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt
>
> diff --git a/Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt
> b/Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt
> new file mode 100644
> index 000000000000..2e7c5aa7020f
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt
> @@ -0,0 +1,85 @@
> +Allwinner A31 DSI Encoder
> +=========================
> +
> +The DSI pipeline consists of two separate blocks: the DSI controller
> +itself, and its associated D-PHY.
> +
> +DSI Encoder
> +-----------
> +
> +The DSI Encoder generates the DSI signal from the TCON's.
> +
> +Required properties:
> + - compatible: value must be one of:
> + * allwinner,sun6i-a31-mipi-dsi
> + - reg: base address and size of memory-mapped region
> + - interrupts: interrupt associated to this IP
> + - clocks: phandles to the clocks feeding the DSI encoder
> + * bus: the DSI interface clock
> + * mod: the DSI module clock
> + - clock-names: the clock names mentioned above
> + - phys: phandle to the D-PHY
> + - phy-names: must be "dphy"
> + - resets: phandle to the reset controller driving the encoder
> +
> + - ports: A ports node with endpoint definitions as defined in
> + Documentation/devicetree/bindings/media/video-interfaces.txt. The
> + port should be the input endpoint, usually coming from the
> + associated TCON.
Output port for bridge/panel?
> +
> +D-PHY
> +-----
> +
> +Required properties:
> + - compatible: value must be one of:
> + * allwinner,sun6i-a31-mipi-dphy
> + - reg: base address and size of memory-mapped region
> + - clocks: phandles to the clocks feeding the DSI encoder
> + * bus: the DSI interface clock
> + * mod: the DSI module clock
> + - clock-names: the clock names mentioned above
> + - resets: phandle to the reset controller driving the encoder
> +
> +Example:
> +
> +dsi0: dsi@01ca0000 {
Drop the leading 0.
> + compatible = "allwinner,sun6i-a31-mipi-dsi";
> + reg = <0x01ca0000 0x1000>;
> + interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ccu CLK_BUS_MIPI_DSI>,
> + <&ccu CLK_DSI_SCLK>;
> + clock-names = "bus", "mod";
> + resets = <&ccu RST_BUS_MIPI_DSI>;
> + phys = <&dphy0>;
> + phy-names = "dphy";
> + #address-cells = <1>;
> + #size-cells = <0>;
Not needed.
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + dsi0_in: port@0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0>;
> +
> + dsi0_in_tcon0: endpoint@0 {
> + reg = <0>;
Don't need reg when there's only 1 endpoint.
> + remote-endpoint = <&tcon0_out_dsi0>;
> + };
> + };
> + };
> +};
> +
> +dphy0: d-phy@01ca1000 {
Drop leading 0.
> + compatible = "allwinner,sun6i-a31-mipi-dphy";
> + reg = <0x01ca1000 0x1000>;
> + clocks = <&ccu CLK_BUS_MIPI_DSI>,
> + <&ccu CLK_DSI_DPHY>;
> + clock-names = "bus", "mod";
> + resets = <&ccu RST_BUS_MIPI_DSI>;
> + #address-cells = <1>;
> + #size-cells = <0>;
For what?
> + #phy-cells = <0>;
> +};
> --
> git-series 0.9.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
