On Monday 17 Jul 2017 13:41:49 Rob Herring wrote:
> On Thu, Jul 13, 2017 at 04:13:06PM +0200, Maxime Ripard wrote:
> > The Allwinner SoCs usually come with a DSI encoder. Add a binding for it.
> >
> > Signed-off-by: Maxime Ripard <maxime.rip...@free-electrons.com>
> > ---
> >
> > Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt | 85
> > +++++++-
> > 1 file changed, 85 insertions(+)
> > create mode 100644
> > Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt>
> > diff --git a/Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt
> > b/Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt new file
> > mode 100644
> > index 000000000000..2e7c5aa7020f
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt
> > @@ -0,0 +1,85 @@
> > +Allwinner A31 DSI Encoder
> > +=========================
> > +
> > +The DSI pipeline consists of two separate blocks: the DSI controller
> > +itself, and its associated D-PHY.
> > +
> > +DSI Encoder
> > +-----------
> > +
> > +The DSI Encoder generates the DSI signal from the TCON's.
> > +
> > +Required properties:
> > + - compatible: value must be one of:
> > + * allwinner,sun6i-a31-mipi-dsi
> > + - reg: base address and size of memory-mapped region
> > + - interrupts: interrupt associated to this IP
> > + - clocks: phandles to the clocks feeding the DSI encoder
> > + * bus: the DSI interface clock
> > + * mod: the DSI module clock
> > + - clock-names: the clock names mentioned above
> > + - phys: phandle to the D-PHY
> > + - phy-names: must be "dphy"
> > + - resets: phandle to the reset controller driving the encoder
> > +
> > + - ports: A ports node with endpoint definitions as defined in
> > + Documentation/devicetree/bindings/media/video-interfaces.txt. The
> > + port should be the input endpoint, usually coming from the
> > + associated TCON.
>
> Output port for bridge/panel?
>
> > +
> > +D-PHY
> > +-----
> > +
> > +Required properties:
> > + - compatible: value must be one of:
> > + * allwinner,sun6i-a31-mipi-dphy
> > + - reg: base address and size of memory-mapped region
> > + - clocks: phandles to the clocks feeding the DSI encoder
> > + * bus: the DSI interface clock
> > + * mod: the DSI module clock
> > + - clock-names: the clock names mentioned above
> > + - resets: phandle to the reset controller driving the encoder
> > +
> > +Example:
> > +
> > +dsi0: dsi@01ca0000 {
>
> Drop the leading 0.
>
> > + compatible = "allwinner,sun6i-a31-mipi-dsi";
> > + reg = <0x01ca0000 0x1000>;
> > + interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&ccu CLK_BUS_MIPI_DSI>,
> > + <&ccu CLK_DSI_SCLK>;
> > + clock-names = "bus", "mod";
> > + resets = <&ccu RST_BUS_MIPI_DSI>;
> > + phys = <&dphy0>;
> > + phy-names = "dphy";
> >
> > + #address-cells = <1>;
> > + #size-cells = <0>;
>
> Not needed.
>
> > +
> > + ports {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + dsi0_in: port@0 {
I don't think the label for the port is needed, you should only reference the
endpoint.
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + reg = <0>;
> > +
> > + dsi0_in_tcon0: endpoint@0 {
> > + reg = <0>;
>
> Don't need reg when there's only 1 endpoint.
And no reg for the port name either when there's a single port. This can all
be simplified to
dsi0: dsi@1ca0000 {
compatible = "allwinner,sun6i-a31-mipi-dsi";
reg = <0x01ca0000 0x1000>;
interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_MIPI_DSI>,
<&ccu CLK_DSI_SCLK>;
clock-names = "bus", "mod";
resets = <&ccu RST_BUS_MIPI_DSI>;
phys = <&dphy0>;
phy-names = "dphy";
port {
dsi0_in_tcon0: endpoint {
remote-endpoint = <&tcon0_out_dsi0>;
};
};
};
> > + remote-endpoint = <&tcon0_out_dsi0>;
> > + };
> > + };
> > + };
> > +};
[snip]
--
Regards,
Laurent Pinchart
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
