The Northwest Logic MIPI DSI IP core can be found in NXPs i.MX8 SoCs.
Signed-off-by: Guido Günther <a...@sigxcpu.org>
---
.../bindings/display/bridge/imx-nwl-dsi.txt | 89 +++++++++++++++++++
1 file changed, 89 insertions(+)
create mode 100644
Documentation/devicetree/bindings/display/bridge/imx-nwl-dsi.txt
diff --git a/Documentation/devicetree/bindings/display/bridge/imx-nwl-dsi.txt
b/Documentation/devicetree/bindings/display/bridge/imx-nwl-dsi.txt
new file mode 100644
index 000000000000..288fdb726d5a
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/bridge/imx-nwl-dsi.txt
@@ -0,0 +1,89 @@
+Northwest Logic MIPI-DSI on imx SoCs
+=====================================
+
+NWL MIPI-DSI host controller found on i.MX8 platforms. This is a
+dsi bridge for the for the NWL MIPI-DSI host.
+
+Required properties:
+- compatible: "fsl,<chip>-nwl-dsi"
+ The following strings are expected:
+ "fsl,imx8mq-nwl-dsi"
+- reg: the register range of the MIPI-DSI controller
+- interrupts: the interrupt number for this module
+- clock, clock-names: phandles to the MIPI-DSI clocks
+ The following clocks are expected on all platforms:
+ "core" - DSI core clock
+ "tx_esc" - TX_ESC clock (used in escape mode)
+ "rx_esc" - RX_ESC clock (used in escape mode)
+ "phy_ref" - PHY_REF clock. Clock is managed by the phy. Only
+ used to read the clock rate.
+- assigned-clocks: phandles to clocks that require initial configuration
+- assigned-clock-rates: rates of the clocks that require initial
configuration
+ The following clocks need to have an initial configuration:
+ "tx_esc" (20 MHz) and "rx_esc" (80 Mhz).
+- phys: phandle to the phy module representing the DPHY
+ inside the MIPI-DSI IP block
+- phy-names: should be "dphy"
+
+Optional properties:
+- power-domains phandle to the power domain
+- src phandle to the system reset controller (required on
+ i.MX8MQ)
+- mux-sel phandle to the MUX register set (required on i.MX8MQ)
+- assigned-clock-parents phandles to parent clocks that needs to be assigned as
+ parents to clocks defined in assigned-clocks
+
+Example:
+ mipi_dsi: mipi_dsi@30a00000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx8mq-nwl-dsi";
+ reg = <0x30A00000 0x300>;
+ clocks = <&clk IMX8MQ_CLK_DSI_CORE>,
+ <&clk IMX8MQ_CLK_DSI_AHB>,
+ <&clk IMX8MQ_CLK_DSI_IPG_DIV>,
+ <&clk IMX8MQ_CLK_DSI_PHY_REF>;
+ clock-names = "core", "rx_esc", "tx_esc", "phy_ref";
+ assigned-clocks = <&clk IMX8MQ_CLK_DSI_AHB>,
+ <&clk IMX8MQ_CLK_DSI_CORE>,
+ <&clk IMX8MQ_CLK_DSI_IPG_DIV>;
+ assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_80M>,
+ <&clk IMX8MQ_SYS1_PLL_266M>;
+ assigned-clock-rates = <80000000>,
+ <266000000>,
+ <20000000>;
+ interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&pgc_mipi>;
+ src = <&src>;
+ mux-sel = <&iomuxc_gpr>;
+ phys = <&dphy>;
+ phy-names = "dphy";
+ status = "okay";
+
+ panel@0 {
+ compatible = "...";
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&mipi_dsi_out>;
+ };
+ };
+ };
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ mipi_dsi_in: endpoint {
+ remote-endpoint =
<&dcss_disp0_mipi_dsi>;
+ };
+ };
+ port@1 {
+ reg = <1>;
+ mipi_dsi_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+ };
--
2.20.1
