Hi Laurent,
thanks for having a look.
On Sat, Jul 27, 2019 at 04:57:16AM +0300, Laurent Pinchart wrote:
> Hi Guido,
>
> Thank you for the patch.
>
> On Wed, Jul 24, 2019 at 05:52:25PM +0200, Guido Günther wrote:
> > The Northwest Logic MIPI DSI IP core can be found in NXPs i.MX8 SoCs.
> >
> > Signed-off-by: Guido Günther <a...@sigxcpu.org>
> > ---
> > .../bindings/display/bridge/imx-nwl-dsi.txt | 89 +++++++++++++++++++
> > 1 file changed, 89 insertions(+)
> > create mode 100644
> > Documentation/devicetree/bindings/display/bridge/imx-nwl-dsi.txt
> >
> > diff --git
> > a/Documentation/devicetree/bindings/display/bridge/imx-nwl-dsi.txt
> > b/Documentation/devicetree/bindings/display/bridge/imx-nwl-dsi.txt
> > new file mode 100644
> > index 000000000000..288fdb726d5a
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/display/bridge/imx-nwl-dsi.txt
> > @@ -0,0 +1,89 @@
> > +Northwest Logic MIPI-DSI on imx SoCs
> > +=====================================
>
> There's one too many =.
>
> > +
> > +NWL MIPI-DSI host controller found on i.MX8 platforms. This is a
> > +dsi bridge for the for the NWL MIPI-DSI host.
>
> s/dsi/DSI/
> s/for the for the /for the /
>
> > +
> > +Required properties:
> > +- compatible: "fsl,<chip>-nwl-dsi"
> > + The following strings are expected:
> > + "fsl,imx8mq-nwl-dsi"
> > +- reg: the register range of the MIPI-DSI controller
> > +- interrupts: the interrupt number for this module
>
> It's not just a number but a specifier (with flags).
>
> > +- clock, clock-names: phandles to the MIPI-DSI clocks
>
> That should be phandles and names.
>
> > + The following clocks are expected on all platforms:
>
> Expected or required ?
>
> s/ on all platforms// as you only support a single platform.
>
> > + "core" - DSI core clock
> > + "tx_esc" - TX_ESC clock (used in escape mode)
> > + "rx_esc" - RX_ESC clock (used in escape mode)
> > + "phy_ref" - PHY_REF clock. Clock is managed by the phy. Only
> > + used to read the clock rate.
> > +- assigned-clocks: phandles to clocks that require initial configuration
> > +- assigned-clock-rates: rates of the clocks that require initial
> > configuration
> > + The following clocks need to have an initial configuration:
> > + "tx_esc" (20 MHz) and "rx_esc" (80 Mhz).
>
> I think those two properties are out of scope for these bindings.
>
> > +- phys: phandle to the phy module representing the DPHY
> > + inside the MIPI-DSI IP block
> > +- phy-names: should be "dphy"
> > +
> > +Optional properties:
> > +- power-domains phandle to the power domain
> > +- src phandle to the system reset controller
> > (required on
> > + i.MX8MQ)
>
> Should this use the standard resets property ?
>
> > +- mux-sel phandle to the MUX register set (required on i.MX8MQ)
> > +- assigned-clock-parents phandles to parent clocks that needs to be
> > assigned as
> > + parents to clocks defined in assigned-clocks
>
> This property is also out of scope.
>
> > +
> > +Example:
> > + mipi_dsi: mipi_dsi@30a00000 {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + compatible = "fsl,imx8mq-nwl-dsi";
> > + reg = <0x30A00000 0x300>;
> > + clocks = <&clk IMX8MQ_CLK_DSI_CORE>,
> > + <&clk IMX8MQ_CLK_DSI_AHB>,
> > + <&clk IMX8MQ_CLK_DSI_IPG_DIV>,
> > + <&clk IMX8MQ_CLK_DSI_PHY_REF>;
> > + clock-names = "core", "rx_esc", "tx_esc", "phy_ref";
> > + assigned-clocks = <&clk IMX8MQ_CLK_DSI_AHB>,
> > + <&clk IMX8MQ_CLK_DSI_CORE>,
> > + <&clk IMX8MQ_CLK_DSI_IPG_DIV>;
> > + assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_80M>,
> > + <&clk IMX8MQ_SYS1_PLL_266M>;
> > + assigned-clock-rates = <80000000>,
> > + <266000000>,
> > + <20000000>;
> > + interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
> > + power-domains = <&pgc_mipi>;
> > + src = <&src>;
> > + mux-sel = <&iomuxc_gpr>;
> > + phys = <&dphy>;
> > + phy-names = "dphy";
> > + status = "okay";
> > +
> > + panel@0 {
> > + compatible = "...";
> > + port {
> > + panel_in: endpoint {
> > + remote-endpoint = <&mipi_dsi_out>;
> > + };
> > + };
> > + };
> > +
> > + ports {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + port@0 {
> > + reg = <0>;
> > + mipi_dsi_in: endpoint {
> > + remote-endpoint =
> > <&dcss_disp0_mipi_dsi>;
> > + };
> > + };
> > + port@1 {
> > + reg = <1>;
> > + mipi_dsi_out: endpoint {
> > + remote-endpoint = <&panel_in>;
> > + };
> > + };
> > + };
>
> The ports should be documented too. There are multiple example bindings
> available.
I've followed you suggestions while moving the whole thing to YAML
syntax for an upcoming v2.
Thanks for having a look,
Cheers,
-- Guido
> > + };
>
> --
> Regards,
>
> Laurent Pinchart
>
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
