Yes, You must be running this thing at about 1600x1200... Your highest 
mode for 16 bit is 1024x768. You really wouldn't get any preformance at 
a higher resolution anyway.  And highest for 24(32)bit is 800x600, but 
use 16bit.

Dagfinn Ilmari Mannsåker wrote:

>On Mon, Oct 08, 2001 at 01:56:28AM +0200, Michel Dänzer wrote:
>
>>On Sun, 2001-10-07 at 23:44, Dagfinn Ilmari Mannsåker wrote:
>>
>>>I am very keen on getting DRI up and running on this machine, and I
>>>will assist with any tests and/or troubleshooting you find necessary,
>>>just give me the instructions.
>>>
>>Have you followed the DRI User Guide? There are quite a few things that
>>can prevent direct rendering. Have you looked through the server log
>>carefully?
>>
>
>Yes, I have followed the DRI User Guide (without knowing it. I read through
>it, and I have done exactly as it said). From looking at the log, I can't see
>what would cause direct rendering to fail. The parts of the log relevant to
>the card are:
>
>[ scanpci output: ]
>(--) PCI:*(1:0:0) ATI Rage 128 Mobility LF rev 2, Mem @ 0xf4000000/26,
>0xfdffc000/14, I/O @ 0xec00/8
>[ snip ]
>(--) Chipset ATI Rage 128 Mobility LF (AGP) found
>[ snip ]
>(II) R128(0): PCI bus 1 card 0 func 0
>(**) R128(0): Depth 16, (--) framebuffer bpp 16
>(II) R128(0): Pixel depth = 16 bits stored in 2 bytes (16 bpp pixmaps)
>(==) R128(0): Default visual is TrueColor
>(==) R128(0): RGB weight 565
>(II) R128(0): Using 6 bits per RGB (8 bit DAC)
>(II) R128(0): initializing int10
>(II) R128(0): Primary V_BIOS segment is: 0xc000
>(--) R128(0): Chipset: "ATI Rage 128 Mobility LF (AGP)" (ChipID = 0x4c46)
>(--) R128(0): Linear framebuffer at 0xf4000000
>(--) R128(0): MMIO registers at 0xfdffc000
>(--) R128(0): VideoRAM: 8192 kByte (128-bit SDR SGRAM 1:1)
>(**) R128(0): Using flat panel for display
>(II) R128(0): Panel size: 1400x1050
>(II) R128(0): Panel ID: Samsung LTN141P2
>(II) R128(0): Panel Type: Color, Single, TFT
>(II) R128(0): Panel Interface: LVDS
>(II) R128(0): PLL parameters: rf=2700 rd=12 min=12500 max=25000; xclk=10500
>(II) R128(0): VESA BIOS detected
>(II) R128(0): VESA VBE DDC supported
>(**) R128(0): Using gamma correction (0.7, 0.7, 0.7)
>(II) R128(0): 14.1in TFT: Using hsync range of 31.50-80.00 kHz
>(II) R128(0): 14.1in TFT: Using vrefresh range of 40.00-80.00 Hz
>(II) R128(0): Clock range:  12.50 to 250.00 MHz
>[ snip ]
>(==) R128(0): Write-combining range (0xf4000000,0x800000)
>(WW) R128(0): Static buffer allocation failed -- need at least 8663 kB video
>memory
>(II) R128(0): Memory manager initialized to (0,0) (1408,2978)
>(II) R128(0): Reserved area from (0,1050) to (1408,1052)
>(II) R128(0): Largest offscreen area available: 1408 x 1926
>(==) R128(0): Backing store disabled
>(==) R128(0): Silken mouse enabled
>(II) R128(0): Using XFree86 Acceleration Architecture (XAA)
>        Screen to screen bit blits
>        Solid filled rectangles
>        8x8 mono pattern filled rectangles
>        Indirect CPU to Screen color expansion
>        Solid Lines
>        Dashed Lines
>        Scanline Image Writes
>        Offscreen Pixmaps
>        Setting up tile and stipple cache:
>                32 128x128 slots
>                13 256x256 slots
>                5 512x512 slots
>(II) R128(0): Acceleration enabled
>(II) R128(0): Using hardware cursor (scanline 2104)
>(II) R128(0): Largest offscreen area available: 1408 x 1924
>(II) R128(0): Direct rendering disabled
>
>I have tried with 24bpp too, with the same result.
>



_______________________________________________
Dri-devel mailing list
[EMAIL PROTECTED]
https://lists.sourceforge.net/lists/listinfo/dri-devel

Reply via email to