--- Marco Strack <[EMAIL PROTECTED]> wrote: > ok, changed the code and recompiled the source. > > Now the drm module recognizes the card and inits it. > /dev/dri/card0 is present even though not accessable by any user > besides root. > (flags are ok and i also have a proper DRI Section in config...) > > glxinfo reports dri is enabled. > no gl stuff works. glxgears shows nothing.
DRI support has not been tested on supersavage yet. I think you are the first one. The current DRI code is based on the prosavage/savage4 3D engine. Unfortunately, I'm not sure how similar the 3D engines are between supersavage and savage4. FWIW, I haven't had any luck with savage IX either. > > in X log : > > > this is the card : > > (II) SAVAGE(0): VESA VBE OEM Vendor: S3 Incorporated. > (II) SAVAGE(0): VESA VBE OEM Product: VBE 2.0 > (II) SAVAGE(0): VESA VBE OEM Product Rev: Rev 1.0 > (--) SAVAGE(0): Chip: id 8c2e, "SuperSavage/PM64IXC_SDR" > (--) SAVAGE(0): Engine: "SuperSavage" > (--) SAVAGE(0): mapping MMIO @ 0xc0100000 with size 0x80000 > (II) SAVAGE(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset > is > 0x0000 > (--) S3:support device 15. > (--) S3:tv size 0x0. > > > > this is drm stuff : > > > (--) SAVAGE(0): mapping framebuffer @ 0xe8000000 with size 0x1000000 > (==) SAVAGE(0): Write-combining range (0xe8000000,0x1000000) > (II) SAVAGE(0): Splitting WC range: base: 0xe4000000, size: 0x5000000 > (==) SAVAGE(0): Write-combining range (0xe8000000,0x1000000) > (==) SAVAGE(0): Write-combining range (0xe4000000,0x5000000) > (II) SAVAGE(0): map aperture:0x41301000 > (--) SAVAGE(0): SavageMatchBiosMode:chose mode 13e at 75Hz. > (II) SavageSetVESAMode:mode=0x13e,refresh=75HZ > (II) SAVAGE(0): [drm] bpp: 32 depth: 24 > (II) SAVAGE(0): [drm] Sarea 2200+872: 3072 > drmOpenDevice: node name is /dev/dri/card0 > drmOpenDevice: open result is 7, (OK) > drmOpenDevice: node name is /dev/dri/card0 > drmOpenDevice: open result is 7, (OK) > drmOpenByBusid: Searching for BusID pci:0000:01:00.0 > drmOpenDevice: node name is /dev/dri/card0 > drmOpenDevice: open result is 7, (OK) > drmOpenByBusid: drmOpenMinor returns 7 > drmOpenByBusid: drmGetBusid reports pci:0000:01:00.0 > (II) SAVAGE(0): [drm] DRM interface version 1.1 > (II) SAVAGE(0): [drm] created "savage" driver at busid > "pci:0000:01:00.0" > (II) SAVAGE(0): [drm] added 8192 byte SAREA at 0xe08d9000 > (II) SAVAGE(0): [drm] mapped SAREA 0xe08d9000 to 0x46301000 > (II) SAVAGE(0): [drm] framebuffer handle = 0xe8000000 > (II) SAVAGE(0): [drm] added 1 reserved context for kernel > (II) SAVAGE(0): [agp] Mode 0x1f000217 [AGP 0x8086/0x3575; Card > 0x5333/0x8c2e] > (II) SAVAGE(0): [agp] 16384 kB allocated with handle 0x00000001 > (II) SAVAGE(0): [agp] agpTextures microcode handle = 0xd0000000 > (II) SAVAGE(0): [agp] agpTextures mapped at 0x00000000 > (II) SAVAGE(0): [drm] aperture handle = 0xe4000000 > (II) SAVAGE(0): [drm] Status handle = 0xe08f4000 > (II) SAVAGE(0): [agp] Status page mapped at 0x46303000 > (II) SAVAGE(0): [dri] visual configs initialized > (**) SAVAGE(0): DRI is enabled > (II) SAVAGE(0): virtualX:1400,virtualY:1050 > (II) SAVAGE(0): bpp:32,tiledwidthBytes:5632,tiledBufferSize:5947392 > (II) SAVAGE(0): bpp:32,widthBytes:5632,BufferSize:5914624 > (II) SAVAGE(0): videoRambytes:0x01000000 > (II) SAVAGE(0): textureSize:0xffce3000 > (II) SAVAGE(0): textureSize:0x00000000 > (II) SAVAGE(0): textureOffset:0x00fdf000 > (II) SAVAGE(0): depthOffset:0x00a33000,depthPicth:5632 > (II) SAVAGE(0): backOffset:0x00487000,backPicth:5632 > (EE) SAVAGE(0): Memory manager initialization to (0,0) (1408,-1) > failed > (==) SAVAGE(0): Backing store disabled > (**) Option "dpms" > (**) SAVAGE(0): DPMS enabled > (II) SAVAGE(0): X context handle = 0x00000001 > (II) SAVAGE(0): [drm] installed DRM signal handler > (II) SAVAGE(0): [DRI] installation complete > (II) SAVAGE(0): [junkers]pSAVAGEDRIServer: > [LOTS OF STUFF DELETED] > (II) SAVAGE(0): [junkers] BCIcmdBuf:map:0x00010000 > (II) SAVAGE(0): [junkers] status:handle:0xe08f4000 > (II) SAVAGE(0): [junkers] status:offset:0x00000000 > (II) SAVAGE(0): [junkers] status:size:0x00002000 > (II) SAVAGE(0): [junkers] status:map:0x00000000 > (II) SAVAGE(0): [junkers] sarea_priv_offset:0x00000898 > (II) SAVAGE(0): Direct rendering enabled > (--) SAVAGEInitMC: There is no enough memory! > (**) SAVAGE(0): XvMC is not enabled > (WW) SAVAGE(0): Option "ForceInit" is not used > (==) RandR enabled > > > -- snip.---- > > see the "not enough memory" error... Don't worry about that. That's the HW XvMC support. it's shares memory with the DRI. If you want to try the XvMC stuff, lower your bit depth to 16 bpp. Also 32 bpp DRI support is broken right now, at least on savage4. You may also need to disable linear framebuffer mode: Option "disabletile" "false" Alex > > Hope this helps... ;) Thanks for testing! > > regards Marco > Alex __________________________________ Do you Yahoo!? Yahoo! Hotjobs: Enter the "Signing Bonus" Sweepstakes http://hotjobs.sweepstakes.yahoo.com/signingbonus ------------------------------------------------------- This SF.net email is sponsored by: Perforce Software. Perforce is the Fast Software Configuration Management System offering advanced branching capabilities and atomic changes on 50+ platforms. Free Eval! http://www.perforce.com/perforce/loadprog.html -- _______________________________________________ Dri-devel mailing list [EMAIL PROTECTED] https://lists.sourceforge.net/lists/listinfo/dri-devel
