Hmm, if the network type is unknown, obviously your pvr is stripping out some stuff that TSReader uses to determine the network type. It might not even be transport stream anymore. It is usually quite difficult to get decrypted transport stream out of a consumer STB. If the channel however isn't encrypted, there are other options (recording directly in TSReader using an ATSC tuner card that can do QAM). Even if the channel is encrypted, if you know what physical carrier it's on on your cable system (or you could check them all - I'll bet they're all the same), you can look at the whole transport stream with a QAM card and see if it's identified as DCII. I've seen TSR compatable QAM cards on ebay fairly cheap these days. Specifically, the newer version of the Technisat Airstar HD5000 (but you have to make sure it's the newer version - the old one doesn't do QAM).
Andrew On Fri, Dec 5, 2008 at 9:24 AM, Cengiz Gunay <[EMAIL PROTECTED]> wrote: > > On Wed, 3 Dec 2008, Andrew Hakman wrote: > >> Most likely your problem is on a digicipher2 channel. Digicipher2 is a >> system that most cable companies use, and is slightly different than >> DVB (it was standardized just before DVB). Most of the files I have to >> cut with dvbcut because no other program will touch them are >> digicipher. There are some subtle differences in the tables, stream >> identifiers, and the GOP structure I believe that confuses other >> programs like projectX, or anything else that strictly adheres to DVB >> specs. If you really want to know what kind of stream it is, download >> the trial version of TSReader ( http://www.tsreader.com/legacy/ ), >> start it with the "file" source, and load in your file. It will parse >> the tables, and show you all kinds of useful info, including the >> network type in the lower left corner (DVB/ATSC/DCII). This is of >> course if you actually have a transport stream file, and not a program >> stream file. Unfortunately, there is no linux version, but it works >> well in WINE (or in virtual box). > > I ran TSReader Lite and loaded a problematic file, but I don't see any > indication of Digicipher2. Where should I look for that? The Network Type > is 'unknown'. Source is a Transport Stream. No errors in the MPEG2 > statistics. The PMT and PIDs are all detected correctly. > > It's really a useful program. I used to delete recordings because I > couldn't find PIDs. Maybe now TSReader can help. > > Thanks again. > > Michael: I'll write back after I extract a sample and test it with DVBCut > r138. > > Cengiz Gunay > -- > [EMAIL PROTECTED] [EMAIL PROTECTED] (MSN) [EMAIL PROTECTED] > Lab: +1-404-727-3565 Home/Cell: +1-678-559-8694 > http://userwww.service.emory.edu/~cgunay/ > IMs: ICQ# 21104923, [EMAIL PROTECTED],yahoo.com,Skype} > -- > > ------------------------------------------------------------------------------ > SF.Net email is Sponsored by MIX09, March 18-20, 2009 in Las Vegas, Nevada. > The future of the web can't happen without you. Join us at MIX09 to help > pave the way to the Next Web now. Learn more and register at > http://ad.doubleclick.net/clk;208669438;13503038;i?http://2009.visitmix.com/ > _______________________________________________ > DVBCUT-user mailing list > DVBCUT-user@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/dvbcut-user > ------------------------------------------------------------------------------ SF.Net email is Sponsored by MIX09, March 18-20, 2009 in Las Vegas, Nevada. The future of the web can't happen without you. Join us at MIX09 to help pave the way to the Next Web now. Learn more and register at http://ad.doubleclick.net/clk;208669438;13503038;i?http://2009.visitmix.com/ _______________________________________________ DVBCUT-user mailing list DVBCUT-user@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/dvbcut-user