Hola! Humbly, desperately seeking help.
I have a Pioneer DVR-103 drive inside a box running the Linux 2.4.18 kernel. I'm using the sg, scsi_mod and ide-scsi modules (ie, not built directly into the kernel) and have the drive's ide device (hdb, in this case) listed in an 'append="hdb=ide-scsi"' line in my lilo.conf (which shows up in /proc/cmdline). I can read CDs, read DVDs and write CD-Rs without problems. (Dummy) attempts to write an ISO9660 image from a hard disk to a TDK 2x DVD-R, however, fail with SCSI problems which I am not equipped to diagnose. I have tried at speed=2 and speed=2; I have tried with and without -nofix; I have tried dvrtools v0.1.3 and cdrecord-prodvd 2.0; the SCSI error, however, is always the same, though it sometimes occurs after only 200Mb and sometimes not until after 2Gb. The error: dvdrecord: Input/output error. write_g1: scsi sendcmd: no error CDB: 2A 00 00 09 25 59 00 00 1F 00 status: 0x2 (CHECK CONDITION) Sense Bytes: 70 00 04 00 00 00 00 0E 00 00 00 00 08 01 00 00 Sense Key: 0x4 Hardware Error, Segment 0 Sense Code: 0x08 Qual 0x01 (logical unit communication time-out) Fru 0x0 Sense flags: Blk 0 (not valid) cmd finished after 2.007s timeout 200s Sense Bytes: 70 00 00 00 00 00 00 0E 00 00 00 00 00 00 00 00 00 00 Sadly, this is all greek to me. I will copy the complete output of one of the runs below. Thanks in advance for all advice provided, m Complete output... scsidev: '0,0,0' scsibus: 0 target: 0 lun: 0 Linux sg driver version: 3.1.22 dvdrtools v0.1.3 Portions (c) 2002-2003 Ark Linux <[EMAIL PROTECTED]> Based on: Cdrecord 1.11a15 (i686-pc-linux-gnu) Copyright (C) 1995-2001 J�rg Schilling TOC Type: 1 = CD-ROM Using libscg version 'schily-0.5' atapi: 1 Device type : Removable CD-ROM Version : 0 Response Format: 2 Capabilities : Vendor_info : 'PIONEER ' Identifikation : 'DVD-RW DVR-103 ' Revision : '1.90' Device seems to be: Generic mmc2 DVD. Using generic SCSI-3/mmc DVD-R(W) driver (mmc_mdvd). Driver flags : SWABAUDIO Supported modes: PACKET SAO Drive buf size : 1245184 = 1216 KB FIFO size : 4194304 = 4096 KB Track 01: data 4010 MB Total size: 4606 MB (456:20.78) = 2053559 sectors Lout start: 4606 MB (456:22/59) = 2053559 sectors Current Secsize: 2048 ATIP start of lead in: -150 (00:00/00) Disk type: unknown Manuf. index: -1 Manufacturer: unknown (not in table) Blocks total: 2298496 Blocks current: 2298496 Blocks remaining: 244937 Starting to write CD/DVD at speed 2 in dummy mode for single session. Last chance to quit, starting dummy write in 0 seconds. Operation starts. Waiting for reader process to fill input buffer ... input buffer ready. trackno=0 Sending CUE sheet... dvdrecord: WARNING: Drive returns wrong startsec (0) using -150 Starting new track at sector: 0 Track 01: 1170 of 4010 MB written (fifo 96%).dvdrecord: Input/output error. write_g1: scsi sendcmd: no error CDB: 2A 00 00 09 25 59 00 00 1F 00 status: 0x2 (CHECK CONDITION) Sense Bytes: 70 00 04 00 00 00 00 0E 00 00 00 00 08 01 00 00 Sense Key: 0x4 Hardware Error, Segment 0 Sense Code: 0x08 Qual 0x01 (logical unit communication time-out) Fru 0x0 Sense flags: Blk 0 (not valid) cmd finished after 2.007s timeout 200s Sense Bytes: 70 00 00 00 00 00 00 0E 00 00 00 00 00 00 00 00 00 00 write track data: error after 1227540480 bytes Writing time: 475.051s dvdrecord: fifo had 19399 puts and 19336 gets. dvdrecord: fifo was 0 times empty and 6931 times full, min fill was 92%. _______________________________________________ Dvdrtools-users mailing list [EMAIL PROTECTED] http://mail.nongnu.org/mailman/listinfo/dvdrtools-users
