John, I use the RIGblaster Plus with an Icom 756 ProIII, DX4Win 7.01, MMTY in FSK, and a WaveNode wattmeter (LPT port interface). I operate phone, CW, RTTY, and PSK modes, and it works well _AFTER_ spending a lot of time messing around with the internal jumpers. I can switch between modes instantly without any reconfiguration or switch flipping -- accomplished only by using 2 serial and two parallel ports.
- first serial port for rig control - second serial port for MMTTY transmit control - first parallel LPT port for rotor control - second parallel port for CW keying and Wavenode wattmeter interface If you decide to go with a RIGblaster Plus, let me know -- I'd be happy to share the document I wrote that describes the correct settings in the RB Plus. (( I do not know if those would translate into equal success with a "straight" RIGblaster)) -larry K8UT ----- Original Message ----- From: "John Kjos" <[EMAIL PROTECTED]> To: "DX4WIN" <[email protected]> Sent: Wednesday, October 05, 2005 15:38 Subject: [Dx4win] Rigblaster > Hi again, Is anyone using a Rigblaster with DX4WIN, being able use the > RTTY window in DX4WIN? I have been thinking about getting one. Thanks- > John > EMAIL: [EMAIL PROTECTED] > WEBPAGE: http://www.w9rpm.com/ > AOL IM: W9RPM > > > > _______________________________________________ > Dx4win mailing list > [email protected] > http://mailman.qth.net/mailman/listinfo/dx4win From [EMAIL PROTECTED] Wed Oct 5 19:48:19 2005 From: [EMAIL PROTECTED] (Jay Sewell) Date: Wed Oct 5 19:58:42 2005 Subject: [Dx4win] Rotor Support Message-ID: <[EMAIL PROTECTED]> That's true of the older M2-2800, the new ones have different firmware. > [Original Message] > From: NJ9K <[EMAIL PROTECTED]> > To: <[EMAIL PROTECTED]>; DX4WIN <[email protected]> > Date: 10/5/2005 1:28:26 PM > Subject: RE: [Dx4win] Rotor Support > > I don't have any difficulty using M2-2800 and DX4WIN V7.01...... > > -----Original Message----- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On > Behalf Of Jay Sewell > Sent: Wednesday, October 05, 2005 17:48 > To: DX4WIN > Subject: RE: [Dx4win] Rotor Support > > I spoke with them on the phone and they said it will be supported in the > 7.02 version whenever it comes out. He said that M2 changed the firmware > program without letting anyone know. > The change is minor. Apparently the older rotors respond to A= ###, the > newer versions of the rotor responds to A###. As a stoopgap until the > change is made I have been using HyperTerm for control. > > > 73 Jay W5SL > > > > [Original Message] > > From: John Kjos <[EMAIL PROTECTED]> > > To: DX4WIN <[email protected]> > > Date: 10/5/2005 12:03:00 PM > > Subject: [Dx4win] Rotor Support > > > > Any idea when DX4WIN is going to support the M2 2800 again? Any update in > > the near future? Thanks- John > > EMAIL: [EMAIL PROTECTED] > > WEBPAGE: http://www.w9rpm.com/ > > AOL IM: W9RPM > > > > > > > > _______________________________________________ > > Dx4win mailing list > > [email protected] > > http://mailman.qth.net/mailman/listinfo/dx4win > > > _______________________________________________ > Dx4win mailing list > [email protected] > http://mailman.qth.net/mailman/listinfo/dx4win
