Hi Kostas and others, Paul and I discussed the problems with the OMNI VII Earlier this week but we didn´t have one to test with, The mayor problem with this rig is the commands that Tentec use (example |=CR - vertical bar = carriage return) Since no other radio use these shortcuts or whatever you call them They are not recognized in DX4WIN (for the moment being)
After reading the last mail this morning I drove 300 KM To pick up a omni VII from a friend to debug all the possibilities With Paul. (maybe later today or this week) Since I didn´t have the original supplied serial cable brought with me I took a straight (working) serial cable like they write in there manual, But this doesn´t work !!!!!!!!!!!!!! (works ok with my LP100A) tried with several programs. Got it working with a trusted USB to serial converter where I can arrange the pins Only 5 connections are needed btw. (If I wasn´t smarter I could have start yelling stupid programs They never work etc etc). Most of the time the problems with radios or other connected items is not software related but a hardware problem. I had 10 or even more(different brands) USB to serial adapters but only one brand Does the job 100% correct. With hyperterminal and a loopback dongle you can check if all your hardware Is working perfect. BTW Kostas A serial port in your computer can only be used 1 time. Dx4win checks if available and use it if configured in your preferences otherwise it gives you a message not available etc. Back to the OMNI VII now and see what can be changed in the different rigfiles I have from Some users (K5NA-G4RQI) GUY ON4AOI -----Oorspronkelijk bericht----- Van: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Namens Kostas SV1DPI Verzonden: zaterdag 15 november 2008 22:54 Aan: REFLECTOR dx4win Onderwerp: [Dx4win] omnirig i have seen that many have problems one or other way with rig control. Dx4win is not the problem the most of the time. But maybe it's time Paul and dx4win supports omnirig, a free cat control program. It would be an alternative in every case... Either for a new rig or even to check if there is a problem in dx4win or in your radio (this can be done and today). Besides this someone will have the ability to run 2 programs which both support omnirig the same time... Just a wish.... see omnirig here http://www.dxatlas.com/omnirig/ Kostas sv1dpi ----- Original Message ----- From: "Joe Stepansky" <[EMAIL PROTECTED]> To: <[email protected]> Sent: Saturday, November 15, 2008 10:51 PM Subject: [Dx4win] DX4Win doesn't recognize the rig > For whatever reason, my newly installed DX4Win 7 won't see my rig. I had > no > problem with version 6, but I've seemingly tried everything and it won't > go. > I'm running this through RigBlaster PRO. All the connections appear to be > fine (nothing changed between the time my old computer went bye-bye and > this > one). I'm connected from Serial In/Out A to COM1. Rig control on the > Rigblaster is connected to CI-V remote jack on the 756 PRO II. Here's the > set up under the Preferences/Radio tab: > > > > Type - Icom 756 PRO II > > Address - 64 (I've verified the address on the rig screen) > > Baud - 9600 > > Com Port - COM1 > > Poll Rate - 5000 > > Max Tries - 6 > > DTR High - Off (When I leave this on the rig keys continuously) > > RTS High - Off (When I leave this on the PTT is on continuously) > > > > Any ideas? > > > > 73, Joe KQ3F > > ---------------------------------------------------------------------------- ---- > _______________________________________________ > Dx4win mailing list > [email protected] > http://mailman.qth.net/mailman/listinfo/dx4win > _______________________________________________ Dx4win mailing list [email protected] http://mailman.qth.net/mailman/listinfo/dx4win _______________________________________________ Dx4win mailing list [email protected] http://mailman.qth.net/mailman/listinfo/dx4win
