You will need to log it as a mode valid in both LotW and DX4Win. Could you not log it as JT65? I had the same problem with Olivia until lotw updated their parameter file for TQSL. Which BTW, if I may rant a bit, is NOT obvious... and even though I have done it a couple of times I STILL can't find it again on the site. It's as if they go out of their way to be obtuse... no wonder they scare a lot of users off.
Jay Hainline wrote: > Diving a little deeper, I think I see where the problem lies. Mode in > question is JT6M. Looking at the LOTW web site FAQ, there is a listing of > modes supported by LOTW. Modes are grouped into CW, PHONE, IMAGE and DATA. > JT6M is not listed as one of the currently allowed modes by LOTW and I had > to create a mapping JT6M->DATA in TQSL so I could upload my contact. I also > had created a JT44->DATA mapping in TQSL as that mode was not listed either. > So...I guess LOTW needs to update their accepted modes? I will try and > delete my mappings and try uploading those JT44 and JT6M QSO's. Maybe LOTW > has changed the accepted modes without updating their FAQ. > > Thanks Mel > > > Jay Hainline KA9CFD EN40om > Colchester, IL > > -----Original Message----- > From: Mel [mailto:[email protected]] > Sent: Friday, September 25, 2009 19:56 > To: Jay Hainline > Cc: 'Jim Reisert AD1C'; [email protected] > Subject: Re: [Dx4win] DX4WIN not setting LOTW upload flag > > Check you don't have a spurious mapping set up in TQSL Jay. > > Jay Hainline wrote: >> Jim, I don't think you understand. I DID upload my QSO's with the >> proper mode, however LOTW confirmed it as mode DATA. If LOTW matches >> DATA to any digital mode, then DX4WIN should also. >> >> >> Jay Hainline KA9CFD EN40om >> Colchester, IL >> >> -----Original Message----- >> From: [email protected] [mailto:[email protected]] On Behalf Of >> Jim Reisert AD1C >> Sent: Friday, September 25, 2009 15:56 >> To: Jay Hainline >> Cc: [email protected] >> Subject: Re: [Dx4win] DX4WIN not setting LOTW upload flag >> >> On Fri, Sep 25, 2009 at 8:11 AM, Jay Hainline <[email protected]> wrote: >> >>> I am using ver 8.02 and have ran across a bug when merging the >>> confirmation file generated by LOTW to my dx4win log to set the LOTW >> confirmation flag. >>> Some of my VHF QSO's are logged using the various WSJT digital modes. >>> On LOTW a few of these QSO's were confirmed with the mode "DATA". >>> When I merge the LOTW generated adif file to the DX4WIN log, DX4WIN >>> will not set the confirmation flag for these DATA QSO's since they >>> are in my log as fsk441 or jt6m. >>> >>> I think DX4WIN should recognize DATA as a legitimate mode for any of >>> the digital modes and set the confirmed flag. >> DATA is not a valid ADIF mode, Jay. See: >> >> http://www.adif.org/adif223.htm#Mode%20Enumeration >> >> I would suggest uploading those QSOs again with the correct mode. >> Then the downloaded lotwreport.adi file should have the correct mode, >> and the confirmations will work. >> >> 73 - Jim AD1C >> >> -- >> Jim Reisert AD1C, <[email protected]>, http://www.ad1c.us >> >> >> ______________________________________________________________ >> Dx4win mailing list >> Home: http://mailman.qth.net/mailman/listinfo/dx4win >> Help: http://mailman.qth.net/mmfaq.htm >> Post: mailto:[email protected] >> >> This list hosted by: http://www.qsl.net Please help support this email >> list: http://www.qsl.net/donate.html >> > > > ______________________________________________________________ Dx4win mailing list Home: http://mailman.qth.net/mailman/listinfo/dx4win Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
