If you have measured DX4Win polling at 500ms please describe how you are
doing that. The last time I experimented with polling, any >Preferences
setting below 2000ms was software-adjusted so that it never polled faster
than every 2 seconds.
-larry (K8UT)
-----Original Message-----
From: Radivoj Kar, F6GNZ
Sent: Monday, June 24, 2013 2:26 AM
To: Joe Subich, W4TV ; DX4WIN Refelector
Subject: Re: [Dx4win] [microHAM] MicroKeyer2, DX4WIN, HDSDR and Omni-Rig
Thanks Joe ! I have created an additional port for COM2 and set Omni-rig to
this port with 1200 ms polling time (DX4WIN polls each 500ms). All works
fine except when I select both Sync from Omni-Rig and Sync to Omni-rig to be
able to set TX to RX-ed frequency but also to set RX frequency by clicking
on the DX4WIN spots. In this case my IC706 starts to "walk" frequencies,
like it had gone to the scanning mode....So, must chose only one way sync...
best 73, Radi F6GNZ
________________________________
De : "Joe Subich, W4TV" <[email protected]>
À : f6gnz <[email protected]>; microham <[email protected]>
Envoyé le : Samedi 22 juin 2013 15h02
Objet : Re: [microHAM] MicroKeyer2, DX4WIN, HDSDR and Omni-Rig
If you are trying to configure a splitter function, you could try
connecting HDSDR/OmniRig to Router's 2nd CAT port. Otherwise, your
logger developer will probably need to provide an OmniRig option
where OmniRig serves both HDSRD and the logger.
Note, if you use Router's 2nd CAT port, it will be necessary to set any
polling from HDSDR/OmniRig to the very minimum (slowest possible) to
prevent overloading the control channel between Router and the MK II.
73,
... Joe Subich, W4TV
microHAM America
http://www.microHAM-USA.com
http://groups.yahoo.com/group/microHAM
support e-mail: [email protected]
On 6/22/2013 8:01 AM, f6gnz wrote:
I have updated my shack with an SDR which I want to use for reception
only and keep my existing MK2, FT1000MP+ IC706 (for 50 MHz) for transmit
only.
I can control SDR with HDSDR program and synchronize FT1000MP/IC706
frequencies/modes via the Omni-Rig program interfaced with HDSDR. This
combination works perfectly, but now my DX4WIN becomes useless as it
can't read nor control the radio, saying "ie_Open, device already open"
and
"Could not open COM4 for keying, ie_Open, device already open" when I try
to Start the Radio.
So, I can't log the QSOs with related radio data (mode, freq's) nor use
spot clicks to set up the TX/RX frequencies, nor control my antenna
rotator.
Is there any way to make the above combination work together???
Regards,
Radi F6GNZ
------------------------------------
This list is for the exchange of information about the use and operation
of microHAM products.
Anyone with specific hardware support issues should contact microHAM
support at mailto:[email protected].
Yahoo! Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/microHAM/
<*> Your email settings:
Individual Email | Traditional
<*> To change settings online go to:
http://groups.yahoo.com/group/microHAM/join
(Yahoo! ID required)
<*> To change settings via email:
[email protected]
[email protected]
<*> To unsubscribe from this group, send an email to:
[email protected]
<*> Your use of Yahoo! Groups is subject to:
http://docs.yahoo.com/info/terms/
______________________________________________________________
DX4WIN mailing list
Home: http://mailman.qth.net/mailman/listinfo/dx4win
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[email protected]
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
______________________________________________________________
DX4WIN mailing list
Home: http://mailman.qth.net/mailman/listinfo/dx4win
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[email protected]
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
