I had a similar problem last year, where DXbase would not recognize the file. I finally found the problem and all was well after that. Go into the Properties for the file by right clicking on the file and see if it is marked as an Archive, if so, undo this and then try opening it, that fixed the problem for me.
Gene K1GD "Jack" <[EMAIL PROTECTED]>@mailman.qth.net on 09/05/2002 03:29:42 PM Sent by: [EMAIL PROTECTED] To: "JIM BROWN" <[EMAIL PROTECTED]>, "dxb" <[email protected]> cc: <[EMAIL PROTECTED]> Subject: Re: [DXBase] Default.mdb. Jim, Before I would even attempt to offer you advice at this point, I would have to fully understand what you have done and what you are trying to do. It is probably still possible to salvage things but I can't really give you any guidance without knowing what you have done. Maybe we should discuss on the phone? Jack ----- Original Message ----- From: "JIM BROWN" <[EMAIL PROTECTED]> To: "Jack" <[EMAIL PROTECTED]>; "dxb" <[email protected]> Cc: <[EMAIL PROTECTED]> Sent: Thursday, September 05, 2002 3:24 PM Subject: Re: [DXBase] Default.mdb. > Well here I go again. I took cortneys advise and looked to where my files > were going.>DEFAULT.MDB>. I tried to make a correction thru Tony's advice > and put a check in the dxbase/field order I wanted to use.....Now all I get > is Unrecognized database format c:\program files\Scientific > Solutions\DXbase2003\n4zy.mdb. And I cannot get into DXbase at all. I hope > I will not have to dump dxbase and reinstall it. I have back files from > 7/20/2003 as far logs go. but after looking at them the log database on the > back up shows default. Any Ideas ??? Thanks All de Jim N4ZY > ----- Original Message ----- > From: Jack <[EMAIL PROTECTED]> > To: JIM BROWN <[EMAIL PROTECTED]>; dxb <[email protected]> > Sent: Tuesday, August 27, 2002 20:13 PM > Subject: Re: [DXBase] Default.mdb. > > > > Jim, > > > > I believe Tony has given you the answer. But, wanted to also mention that > > since you don't know how you ended up with default.mdb as your active > > database, there is change you have been logging QSOs into a database that > > you didn't think was in use. Best if you check things out and figure out > if > > all is as you expected. As for MMTY engine, suggest you check out the web > > to see if they have by chance added the interface in their program to > > DXbase. We published sample code a long time ago that allows any of these > > digital/rtty programs to log directly into DXbase. We have no plan or > > desire to reinvent the wheel by developing special programs for these. > The > > authors of these programs have done a pretty good job with the digital > > aspects and it's much better to just allow them to interface directly with > > DXbase. > > > > Regards, > > Courtney > > > > ----- Original Message ----- > > From: "JIM BROWN" <[EMAIL PROTECTED]> > > To: "dxb" <[email protected]> > > Sent: Tuesday, August 27, 2002 3:45 PM > > Subject: [DXBase] Default.mdb. > > > > > > Well I got my self in another mess. I was importing adif files from mmtty/ > > zakanaka.some how my qso log now shows Default mdb. I cannot fine a way to > > change it back to N4ZY.mdb ((((((HELP))) pse DE Jim N4ZY.ps will there > > ever be a mmtty engine to go along with the psk?? JIM > > > > > > --- StripMime Report -- processed MIME parts --- > > multipart/alternative > > text/plain (text body -- kept) > > text/html > > The reason this message is shown is because the post was in HTML > > or had an attachment. Attachments are not allowed. > > Please post in Plain-Text only.--- > > _______________________________________________ > > DXBase Reflector - Please visit us on the web at www.dxbase.com > > - - - - - - - - - - - - - - - - - - - - - - - > > To UNSUBSCRIBE please visit: > > http://mailman.qth.net/mailman/listinfo/dxbase > > > > > > > _______________________________________________ DXBase Reflector - Please visit us on the web at www.dxbase.com - - - - - - - - - - - - - - - - - - - - - - - To UNSUBSCRIBE please visit: http://mailman.qth.net/mailman/listinfo/dxbase
